Brother International BAS-326G PS Instruction Manual - English - Page 76

11. TABLE OF ERROR CODES

BAS-326G PS

67

Work clamp-related errors

Code

Cause and remedy

E300

Work clamp home position cannot be detected.

Problem with work clamp motor or poor work clamp home position sensor connection.

Turn off the power, and then check that connector P3 on the PMD P.C. board and connector P5 on the main P.C.

board are properly connected.

E301

Intermittent presser foot raised or lowered position cannot be detected.

Turn off the power, and then check if there are any problems in the intermittent presser foot vertical direction.

E303

Problem with work clamp motor home position adjustment data.

Re-adjust the home position.

Communication and memory-related errors

Code

Cause and remedy

E401

Connection communication error with power supply motor P. C. board detected when power was turned on.

Turn off the power, and then check that connector P6 on the power supply motor P.C. board and connector P17 on

the main P.C. board are properly connected.

E402

Communication error with programmer detected when power is turned on.

Turn off the power, and then check that connector P7 on the main P.C. board is properly connected.

E403

Connection error with PMD P. C. board detected when power was turned on.

Turn off the power, and then check that connector P1 on the PMD P.C. board is properly connected.

E410

Communication error with main P. C. board detected.

Turn off the power, and then turn it back on again.

E411

Communication error with power supply motor P. C. board detected.


E412

Communication error with programmer detected.


E413

Communication error with PMD P. C. board detected.


E420

No CF card is inserted.

E421

Program contents are incorrect and cannot be used, or no data.

Check that the CF card or floppy disk contains data with this program number.

E422

Error occurred while reading the CF card or floppy disk.

Check the data on the CF card or floppy disk.

E424

Insufficient free space on the CF card, or data cannot be written to the floppy disk.

Use a different CF card.

Check if the floppy disk is write-protected and if it has enough free space.

E425

Error occurred while writing to the CF card or floppy disk.

Use the specified type of CF card.

Check if the floppy disk is write-protected and if it has enough free space.

E426

R/W key has not been pressed.

Press the R/W key to load the data.

E427

CF card or floppy disk does not contain any data with this program number.

Check the program number.

Data that has already been loaded into internal memory can be used without having to press the R/W key again.

E430

Data cannot be backed up to main P.C. board.


E440

Data memory error on main P.C. board.


E450

Model selection cannot be read from the machine head memory.

Turn off the power and check that connector P3 on the power supply motor P.C. board is properly connected.

E451

Data cannot be backed up to machine head memory.


E452

Machine head memory is not connected.

Turn off the power, and then check that connector P3 on the power supply motor P.C. board is properly connected.

E474

Internal memory is full and copying is not possible.

Clear the sewing data.

Section	Page
COVER	1
SAFETY INSTRUCTIONS	3
[1] Safety indications and their meanings	3
[2] Notes on safety	4
[3] Warning labels	6
CONTENTS	8
1. NAMES OF MAJOR PARTS	10
2. SPECIFICATIONS	11
3. INSTALLATION	12
3-1. Table processing diagram	12
3-2. Installing the control box	13
3-3. Installing the oil pan	13
3-4. Installing the machine head	14
3-5. Tilting the sewing machine head	18
3-6. Installing the operation panel	18
3-7. Installing the pneumatic unit	19
3-8. Connecting the cords	20
3-9. Connecting the ground wire	22
3-10. Connecting the power cord	23
3-11. Installing the cotton stand	23
3-12. Installing the eye guard	24
3-13. Installing the motor cover	25
3-14. Lubrication	26
3-15. Installing the machine head fixing bolt	27
4. PREPARATION BEFORE SEWING	28
4-1. Installing the needle	28
4-2. Threading the upper thread	28
4-3. Foot switch operating method	29
4-4. Winding the lower thread	30
4-5. Installing the bobbin case	31
4-6. Thread tension	32
4-6-1. Lower thread tension	32
4-6-2. Upper thread tension	32
4-7. Home position detection	33
5. USING THE OPERATION PANEL(BASIC OPERATIONS)	34
5-1. Name and function of each operation panel item	34
5-2. Loading sewing data	36
5-3. Setting the program number	36
5-4. Setting the X-scale and Y-scale	37
5-5. Setting the sewing speed	37
5-6. Checking the sewing pattern	38
5-7. Setting the height of the intermittent presser foot	39
6. USING THE OPERATION PANEL(ADVANCED OPERATIONS)	40
6-1. List of advanced functions	40
6-2. Setting memory switches	41
6-3. List of memory switch settings	42
6-4. Using the lower thread counter	43
6-5. Using the production counter	44
6-6. Setting the split number	45
6-7. Using user programs	46
6-8. Using cycle programs	49
6-9. Direct selection (combination table)	51
6-10. X and Y parallel movement of sewing pattern	52
6-11. Clearing memory data (reinitialization)	53
7. USING CF CARDS	54
7-1. Notes on handling CF cards (sold separately)	54
7-2. Structure of a CF card folder	54
7-3. Data read/write mode	55
7-3-1. Reading all sewing data from the CF card at once	56
7-3-2. Writing all sewing data to the CF card at once	57
8. SEWING	58
8-1. Sewing	58
8-2. Using the STOP switch	59
8-3. Using the thread wiper switch	59
9. CLEANING	60
9-1. Cleaning the rotary hook	60
9-2. Cleaning the control box air inlet ports	60
9-3. Draining the oil	61
9-4. Cleaning the eye guard	61
9-5. Checking the needle	61
9-6. Lubrication	61
10. STANDARD ADJUSTMENTS	62
10-1. Checking the machine head switch	62
10-2. Arm thread guide R	62
10-3. Thread take-up spring	63
10-4. Adjusting the needle bar height	63
10-5. Adjusting the needle bar lift amount	64
10-6. Adjusting the needle guard	64
10-7. Adjusting the needle clearance	65
10-8. Adjusting the inner rotary hook and hook stopper overlap	65
10-9. Rotary hook lubrication amount	65
10-10. Adjusting the position of the movable knife	66
10-11. Replacing the movable and fixed knives	68
10-11-1. Installing the feed plate	69
10-12. Adjusting the thread wiper	70
10-13. Intermittent presser foot installation position	70
10-14. Changing the intermittent stroke	71
10-15. Adjusting the work clamp lift amount	73
10-16. Adjusting the air pressure	73
11. TABLE OF ERROR CODES	74
12. TROUBLESHOOTING	78
13. 7-SEGMENT DISPLAY	82

Brother International BAS-326G PS Instruction Manual - English - Page 76

TABLE OF ERROR CODES, Work clamp-related errors, Communication and memory-related errors

Page 76 highlights