Home » Brother International Manuals » Sewing Machines » Brother International BAS-761 » Manual Viewer

Brother International BAS-761 Programmer Instruction Manual - English - Page 112

The cylinder operates when chancing option output, two row switch, and two step tension

Get Brother International BAS-761 PDF manuals and user guides

View all Brother International BAS-761 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 112 highlights

Chapter 3 Programming with Command Function Checking the program setting and setting attribute Checking the program setting and setting attribute The following items are displayed. Current coordinate Distance from the previous position in the X and Y axial directions Stitch length End code Current needle position / Total stitch count Stitch data type Needle tacking (*) Two step tension setting (*) Two row switch (*) Option output (*) Slow conversion (*) Feed data type Option output (*) is displayed. Needle tacking is set for each stitch. Two step tension output is set in the current needle position. The clamp is set inside when it is set to ON and is set outside when it is changed from ON to OFF. Whether option output is conducted or not is set. Three successive stitches at low speed are set. Values 500 to 33500 rpm are available for the speed. is displayed. Whether option output is conducted or not is set. The cylinder operates when chancing option output, two row switch, and two step tension setting. The option output is connected to the following ports Number of connector P26(MN-OPT-OUT) Number of common pin Number of signal pin 5 or 6 (+24V) 1 Two row switch can be set only in one position in one program. The newly set point becomes valid if two row switch is already set in the program. Attribute of items marked with * are available for setting. An example of stitch data is shown below. Stitch length Current stitch count Total stitch count Stitch data type Needle tacking (*) Current stitch count Distance from the previous point in the direction of X or Y axis End code Slow conversion (*) Two row switch (*) Option output (*) Two step tension setting (*) Programmer 111

Section	Page
Go to Instruction Manual Top Page	1
Chapter 1 Initial Setup	6
Connection	7
Handling the programmer	8
Turning power ON/OFF	9
Handling of floppy disk	11
Contents	13
Notes for programming	14
Chapter 2 Programming with Help Function	16
Please read before programming	17
Description of icons	21
Programming example	23
Programming for each stitch	23
Lines	25
Curve	27
Double stitch	30
Feed	32
Needle racking	35
Example of modified program	36
Resizing pattern	36
Changing partially	38
Deleting the first stitch	41
Changing the first stitch position	43
Adding sewing point before the first stitch	46
Adding shunting point before the first stitch	49
Moving the shunting point	52
Deleting the shunting point	54
Moving the entire pattern in parallel	56
Deleting a part of the program during programming	58
Programming	59
Creating a line	59
Creating tacking data	59
Creating a curve	60
Carrying out double stitch	61
Creating needle drop data	63
Creating feed data	63
Editing the current data	64
Ending programming	66
Displaying the data image during programming	67
Checking the program setting and setting attribute	67
Deleting a part of data	68
Displaying a pattern image	69
Checking the program setting and	70
Checking each stitch	71
Checking a series of stitches automatically	71
Setting the attribute (stitch data)	71
Setting the attribute (feed data)	72
Editing program	73
Deleting data	77
Chapter 3 Programming with Command Function	78
Please read before programming	79
Panel description and usage	79
Display screen	80
Programming flowchart	80
Description of commands	82
Moving needle point	82
Deleting data	82
Ending programming	82
Creating program	82
Editing data	83
Setting attribute	83
Other operations	84
Programming example	85
Programming for each stitch	85
Lines	86
Curve	87
Double stitch	89
Feed	90
Needle racking	92
Example of modified program	93
Resizing pattern	93
Changing partially	94
Deleting the first stitch	96
Changing the first stitch position	97
Adding sewing point before the first stitch	98
Adding shunting point before the first stitch	100
Moving the shunting point	102
Deleting the shunting point	103
Moving the entire pattern in parallel	104
名称未設定	105
Programming	106
Creating a line	106
Creating a curve	107
Creating double stitch	108
Creating feed data	109
Creating tacking data	110
Ending programming	111
Checking the program setting and	112
Checking attributes	113
Setting needle tacking in a unit of one stitch	114
Setting two step tension output	114
Setting the option output	115
Setting two row switch	115
Low-speed sewing	116
Editing data	117
Changing stitch length of the program	117
Offset	118
Rotating a pattern clockwise (counterclockwise)	119
Resizing	120
Moving in parallel	121
Displaying image	123
Deleting data	124
Deleting a part of data	124
Deleting program data	124
Chapter 4 Reading / Writing Data	126
Reading data	127
Using the operation panel of the main body	129
Writing data	130
Using the operation panel of the main body	132
Deleting data in a floppy disk	133
Formatting a floppy disk	135
Chapter 5 Practical Programming Examples	136
Programming examples	137
Example 1 (Help function)	138
Programming procedure	138
Operating procedure	139
Example 1 (Command function)	142
Programming procedure	142
Operating procedure	143
Example 2 (Help function)	145
Programming procedure	145
Operating procedure	146
Example 2 (Command function)	151
Programming procedure	151