Brother International BES-1210AC Tubular to Cap - English - Page 1

Brother International BES-1210AC Manual

Get Brother International BES-1210AC PDF manuals and user guides View all Brother International BES-1210AC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

BAS-416, BAS-416A & BES-1210 For Technical Assistance Please Call Toll Free 1-877-4BROTHER Remove this screw on each side With the power to the machine in the ON position. 1) Remove the tubular arm (A) attachment by removing the two long screws with a Phillips and flat head. 2) Remove the flat needle plate (A-1) and replace with the cap needle plate (A-2). 3) Turn the machine off and move the switch (L) to "CAP" mode and turn the power back on. 4) Move the needle case to needle #1 using the needle select button. 5) Turn the pulley in the direction of the arrow to 200 degrees. 6) Loosen the screw that secures the presser foot (B) and adjust the height of the presser foot to the thickness of a quarter and then re-tighten screw. 7) Turn the pulley backwards to 100 degrees and raise presser foot with lever. 8) Install the metal bar with the "L" stamped on the top left side by and attach over the locator pins (C). Secure with the long black thumbscrews (D). 9) Slide the cap driver attachment through the sewing arm of the machine. 10) Slide the guide bar (F) into the hole to the rear of the arm until it stops 11) Tighten the black thumb knob (G) to secure the guide bar. 12) Slide the cap driver attachment towards the rear of the machine and position over the metal bar, with L stamped on it, and secure with the two shorter black thumbscrews (E). 12) Swing the "L" shaped plate (H) up behind the pantograph. 13) Attach the two screws (K). NOTE: Do not attach these two screws when not using cap drive system, also please use the proper screws. Other screws can cause mechanical problems. 14) Tighten the phillips or thumb screw (J) located on the right side of the cap system. Note: When securing this screw please be sure it has both a spring washer and flat washer. This will eliminate some registration problems.

  • 1
B
B
A
A
S
S
-
-
4
4
1
1
6
6
,
,
B
B
A
A
S
S
-
-
4
4
1
1
6
6
A
A
&
&
B
B
E
E
S
S
-
-
1
1
2
2
1
1
0
0
For Technical Assistance Please Call Toll Free
1-877-4BROTHER
With the power to the machine in the ON position.
1) Remove the tubular arm (
A
) attachment by removing the two long screws with a Phillips and
flat head.
2) Remove the flat needle plate (
A-1
) and replace with the cap needle plate (
A-2
).
3) Turn the machine off and move the switch (
L
) to “CAP” mode and turn the power back on.
4) Move the needle case to needle #1 using the needle select button.
5) Turn the pulley in the direction of the arrow to 200 degrees.
6) Loosen the screw that secures the presser foot (
B
) and adjust the height of the presser foot to
the thickness of a quarter and then re-tighten screw.
7) Turn the pulley
backwards
to 100 degrees and raise presser foot with lever.
8) Install the metal bar with the “
L
” stamped on the top left side by and attach over the locator
pins (
C
).
Secure with the long black thumbscrews (
D
).
9) Slide the cap driver attachment through the sewing arm of the machine.
10) Slide the guide bar (
F
) into the hole to the rear of the arm until it stops
11) Tighten the black thumb knob (
G
) to secure the guide bar.
12) Slide the cap driver attachment towards the rear of the machine and position over the
metal bar, with L stamped on it, and secure with the two shorter black thumbscrews (
E
).
12) Swing the “L” shaped plate (
H
) up behind the pantograph.
13) Attach the two screws (
K
).
NOTE:
Do not
attach these two screws when not using cap drive
system, also please use the proper screws. Other screws can cause mechanical problems.
14) Tighten the phillips or thumb screw (
J
) located on the right side of the cap system.
Note:
When securing this screw please be sure it has both a spring washer and flat washer.
This
will eliminate some registration problems.
Remove this screw on
each side