Brother International HL-2240 Users Manual - English - Page 62

Service call indications, Main PCB, failure, Fuser unit, Main motor, High voltage, FAN Failure - error light

Page 62 highlights

Control Panel Service call indications 3 If there is an error that cannot be cleared by the user, the machine will show that a service call is needed by lighting up all the LEDs as shown below. 3 If you see the service call indication shown above, turn off the power switch, and then turn it back on and try to print again. If the error is not cleared after turning the power switch off and then back on, press Go, the LEDs will light up as shown in the table below to identify the error. LED error indication LEDs Main PCB failure Toner Drum Error Ready Fuser unit failure 1 Laser unit Main motor High voltage FAN Failure Zero Cross failure failure failure Error 1 If this error occurs, turn off the machine's power switch, wait a few seconds, and then turn it on again. Leave the machine for approx.15 minutes with the power on. If the error occurs again, call your dealer or Brother Customer Service. For example, the LED indication below shows a fuser unit failure. Make a note of the indication, referring to the table on page 58, and report the error status to your dealer or Brother Customer Service. 58

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148

Control Panel
58
3
Service call indications
3
If there is an error that cannot be cleared by the user, the machine will show that a service call is needed by
lighting up all the LEDs as shown below.
If you see the service call indication shown above, turn off the power switch, and then turn it back on and try
to print again.
If the error is not cleared after turning the power switch off and then back on, press
Go
, the LEDs will light up
as shown in the table below to identify the error.
1
If this error occurs, turn off the machine's power switch, wait a few seconds, and then turn it on again. Leave the machine for approx.15 minutes
with the power on. If the error occurs again, call your dealer or Brother Customer Service.
For example, the LED indication below shows a fuser unit failure.
Make a note of the indication, referring to the table on page 58, and report the error status to your dealer or
Brother Customer Service.
LED error indication
LEDs
Main PCB
failure
Fuser unit
failure
1
Laser unit
failure
Main motor
failure
High voltage
failure
FAN Failure
Zero Cross
Error
Toner
Drum
Error
Ready