Brother International HL-5170DNLT Network Users Manual - English - Page 113

Troubleshooting, Overview, Installation Problems

Get Brother International HL-5170DNLT PDF manuals and user guides View all Brother International HL-5170DNLT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

11 Troubleshooting 11 Overview This chapter describes procedures for troubleshooting problems you may encounter with a Brother print server, it is divided into the following sections: 1 Installation Problems 2 Intermittent Problems 3 Protocol-Specific Troubleshooting Installation Problems If you cannot print over the network, check the following: 1 Make sure that the printer is powered on, is on-line and ready to print. Verify that the printer and the configuration are good by printing the printer settings page. Refer to the Quick Setup Guide. If the test fails, check: a If the LED is not blinking after the device is connected to the network, the network firmware settings may be corrupted. Please consult your service representative. b In this event, try to restore the factory default settings of the print server. To learn how to reset the print server, see Chapter 3 "Network factory default setting" on page 3-11 of the User's Guide. Once you have done that, switch the printer off and then on again, and try to print out the configuration page. 11 - 1 TROUBLESHOOTING

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
11 - 1 TROUBLESHOOTING
11
11
Troubleshooting
Overview
This chapter describes procedures for troubleshooting problems you
may encounter with a Brother print server, it is divided into the
following sections:
1
Installation Problems
2
Intermittent Problems
3
Protocol-Specific Troubleshooting
Installation Problems
If you cannot print over the network, check the following:
1
Make sure that the printer is powered on, is on-line and ready to
print.
Verify that the printer and the configuration are good by printing
the printer settings page. Refer to the Quick Setup Guide. If the
test fails, check:
a
If the LED is not blinking after the device is connected to the
network, the network firmware settings may be corrupted.
Please consult your service representative.
b
In this event, try to restore the factory default settings of the
print server. To learn how to reset the print server, see
Chapter 3 "Network factory default setting" on page 3-11 of
the User's Guide. Once you have done that, switch the printer
off and then on again, and try to print out the configuration
page.