Brother International HL1060 Users Manual - English

Brother International HL1060 - B/W Laser Printer Manual

Get Brother International HL1060 - B/W Laser Printer PDF manuals and user guides View all Brother International HL1060 manuals
Add to My Manuals
Save this manual to your list of manuals

Brother International HL1060 manual content summary:

  • Brother International HL1060 | Users Manual - English - Page 1
    Please read this manual thoroughly before using the printer. Brother Laser Printer HL-1060 Series User's Guide Keep this manual in a convenient place for quick and easy reference at all times. I
  • Brother International HL1060 | Users Manual - English - Page 2
    . It is recommended that you save and use the original packaging. The printer should also be adequately insured with your carrier. Warning When shipping the printer, the DRUM UNIT assembly including the TONER CARTRIDGE must be removed from the printer and placed in the plastic bag. Failure to remove
  • Brother International HL1060 | Users Manual - English - Page 3
    Laser Printer HL-1060 Series User's Guide (For USA & CANADA Only) For technical and operational assistance, please call: In USA In CANADA 1-800-276-7746 714-859-9700 Ext. 329 1-800-853-
  • Brother International HL1060 | Users Manual - English - Page 4
    . All other brand and product names mentioned in this User's Guide are registered trademarks of their respective companies. Compilation and Publication Notice Under the supervision of Brother Industries Ltd., this manual has been compiled and published, covering the latest product's descriptions
  • Brother International HL1060 | Users Manual - English - Page 5
    The following conventions are used in this User's Guide: Warning Indicates warnings that must be observed to prevent possible personal injury. Caution Indicates cautions that must be observed to use the printer properly or prevent damage to the printer.  Note Indicates notes and useful tips to
  • Brother International HL1060 | Users Manual - English - Page 6
    USER'S GUIDE TABLE OF CONTENTS REGULATIONS ...vi CHAPTER 1 INTRODUCTION 1-1 ABOUT THE GUIDEBOOKS 1-1 Finding Out How to Use the Printer 1-1 ABOUT YOUR PRINTER 1-2 Printer Overview ...1-2 System Requirements in the Brother Printing Solution for Windows 1-3 Features ...1-3 OPERATING AND STORAGE
  • Brother International HL1060 | Users Manual - English - Page 7
    THE TONER CARTRIDGE 5-1 REPLACING THE DRUM UNIT 5-6 ADJUSTING THE PRINT DENSITY 5-10 CLEANING THE PRINTER 5-11 Cleaning the Printer Exterior 5-11 Cleaning the Printer Interior and Drum Unit 5-12 Cleaning the Paper Feed Rollers 5-15 RE-PACKING THE PRINTER 5-16 CHAPTER 6 TROUBLESHOOTING
  • Brother International HL1060 | Users Manual - English - Page 8
    USER'S GUIDE REGULATIONS Federal if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, monitors, printers, facsimile receivers and copy machines world-wide. As an International Energy Star partner, Brother Industries
  • Brother International HL1060 | Users Manual - English - Page 9
    States. One of the following labels on the back of the printer indicates compliance with the FDA regulations and must be attached to laser products marketed in the United States. MANUFACTURED: BROTHER INDUSTRIES (USA) INC. 2950 Brother Blvd., Bartlett, TN 38133, U.S.A. This product complies with FDA
  • Brother International HL1060 | Users Manual - English - Page 10
    89/336/EEC (as amended by 91/263/EEC and 92/31/EEC). Issued by: Brother International Europe Ltd. European Technical Services Division IEC 825 Specification (For 220-240 V Model Only) This printer is a Class 1 laser product as defined in IEC 825 specifications. The label shown below is attached in
  • Brother International HL1060 | Users Manual - English - Page 11
    turvallisuusluokan 1 ylittävälle näkymättömälle lasersäteilylle. Varning - Om apparaten används safe operation the three-pin electrical plug supplied must be inserted only into a standard , consult a qualified electrician. Disconnect device This printer must be installed near a power outlet, which
  • Brother International HL1060 | Users Manual - English - Page 12
    USER'S GUIDE IMPORTANT - Wiring Information (For U.K. only) If the power cord supplied with this printer is not suitable with the same rating as the original fuse. Always replace the fuse cover. Never use a plug with the cover omitted. WARNING - THIS PRINTER MUST BE PROPERLY EARTHED. The wires
  • Brother International HL1060 | Users Manual - English - Page 13
    in the following order: 1. Read the Quick Setup Guide to set up your printer and to ensure proper connection with your computer. It also contains information for installing the printer driver, fonts and Remote Printer Console Program. 2. Read the User's Guide to get information about the following
  • Brother International HL1060 | Users Manual - English - Page 14
    USER'S GUIDE ABOUT YOUR PRINTER Printer Overview Paper Support Multi-Purpose Sheet Feeder 1 Paper Stopper Top Cover Extension Support Wire Output Tray Fig. 1-1 Front View Paper Support Multi-Purpose Sheet Feeder 2 Paper Guide Manual Feed Slot Control Panel Optional Interface Port ( Serial
  • Brother International HL1060 | Users Manual - English - Page 15
    floppy disk supplied with your printer. You can easily install them into your Windows system using our installer program. The driver supports our unique compression mode to enhance printing speed in Windows applications and allows you to choose various printer settings including toner saving mode
  • Brother International HL1060 | Users Manual - English - Page 16
    the dialog box will display "Paper Empty" and instructions for the proper corrective action. t Enhanced Memory Management The printer provides its own data compression technology in the printer hardware and the supplied printer driver software, which can automatically compress graphic data and font
  • Brother International HL1060 | Users Manual - English - Page 17
    the Windows printer driver supplied with your printer. Sleep Mode (Power Save Mode) When the printer is not used for a certain amount of time, sleep mode automatically reduces power consumption. The printer consumes less than 13 W when in sleep mode. Low Running Cost Since the toner cartridge is
  • Brother International HL1060 | Users Manual - English - Page 18
    USER'S GUIDE OPERATING AND STORAGE ENVIRONMENT Please take note of the following before using the printer. Power Supply Use the printer within the specified power range. AC power: ±10% of the rated power voltage in your country Frequency: 50 Hz (220 V- 240 V) or 50/60 Hz (
  • Brother International HL1060 | Users Manual - English - Page 19
    to strong physical shocks or vibrations. Do not expose the printer to open flames or salty or corrosive gases. Do not place objects on top of the printer. Do not place the printer near an air conditioner. Keep the printer horizontal when carrying. Do not cover the slots in the top cover. CHAPTER
  • Brother International HL1060 | Users Manual - English - Page 20
    CHAPTER 2 PAPER HANDLING PAPER SPECIFICATIONS The multi-purpose sheet feeders can handle paper that has the following specifications. t Sheet Feeder 1 (Front) / Manual slot Paper Type Paper Size Cut sheet A4, Letter, Legal, B5, A5, A6, Executive, Custom size (70-216 x 127-356 mm, 2.75
  • Brother International HL1060 | Users Manual - English - Page 21
    USER'S GUIDE Paper Capacity in Feeder Multi-purpose Sheet Feeder: Up to 22 mm (0.87 Xerox 4200 (in USA) / Xerox 80 Premier Paper (in Europe) or equivalent Label: Avery laser label or equivalent Transparency: 3M PP2500 / Avery 5282 (in USA) / STABILO 7250 (in Europe) or equivalent CHAPTER
  • Brother International HL1060 | Users Manual - English - Page 22
    We recommend you use label or transparencies which are designed for use in laser printers. We recommend you use long-grained paper for the best print quality. If the paper has problems feeding from the multi-purpose sheet feeder, use the manual feed slot and try again. You can use recycled paper in
  • Brother International HL1060 | Users Manual - English - Page 23
    USER'S GUIDE The following types of envelopes are not recommended for use. • Damaged, curled, construction • Envelopes not sharply creased • Embossed envelopes • Envelopes already printed by a laser printer • Envelopes pre-printed on the inside • Envelopes that cannot be arranged uniformly when
  • Brother International HL1060 | Users Manual - English - Page 24
    paper size, and orientation in your application software. • If your application software does not support your custom paper size, select the next to the printer. When the printer receives data, it begins the print process by loading paper from the multi-purpose sheet feeder. If the printer is in
  • Brother International HL1060 | Users Manual - English - Page 25
    USER'S GUIDE Loading Paper into the Feeder To load paper into the feeder, follow the multi-purpose sheet feeder by gently pulling the tabs forward towards you. ( Œ ) 2. Move the paper guides horizontally to the widest position. (  ) PULL HERE TO INSERT PAPER Fig.2-4 Opening the Feeder and Moving the
  • Brother International HL1060 | Users Manual - English - Page 26
    the feeder, you must first remove it, put it together with the new paper and then insert the stack in the feeder. 4. Move the paper guide to the appropriate paper width ( Œ ) and close the multi-purpose sheet feeder. (  ) ! Caution Failure to set the paper
  • Brother International HL1060 | Users Manual - English - Page 27
    USER'S GUIDE  Note • If the multi-purpose sheet feeder runs out of paper when you try to print, the Alarm and Paper lamps blink to alert you. You have to load paper in the feeder and push the panel switch to cancel the alarm and continue printing. If paper jams in the printer, the
  • Brother International HL1060 | Users Manual - English - Page 28
    2 PAPER HANDLING Two Side Printing (Manual Duplexing) The supplied printer driver for Windows 95 or Windows 3.1 allows for manual duplex printing both with Feeder 1 and Feeder 2. For more information about settings, see the help text in the printer driver. The printer prints all the even numbered
  • Brother International HL1060 | Users Manual - English - Page 29
    you are using. (  ) CHAPTER 2 -10 Fig. 2-9 Moving the Paper Guide t When you load more than one sheet of paper manually: Open the Setup dialog box of the supplied Windows printer driver and choose Manual Feed in the Paper Source section. Follow the above instructions to load the first page. The
  • Brother International HL1060 | Users Manual - English - Page 30
    CHAPTER 2 PAPER HANDLING  Note • Insert paper firmly into the manual feed slot. • Be sure to load sheet by sheet when using the manual feed slot. CHAPTER 2 -11
  • Brother International HL1060 | Users Manual - English - Page 31
    USER'S GUIDE OUTPUT TRAY AND PAPER SUPPORT WIRE The printer ejects paper with the printed surface face down into the output tray at the front of the printer. When the output tray is closed, the ejected paper comes out sheet by sheet through the slit at the front. When you open the tray,
  • Brother International HL1060 | Users Manual - English - Page 32
    are off. Ready (Paper) Lamp The Ready lamp indicates the current status of the printer. Lamp Off r Blinking r£q Blinking r£q On q Printer status The power switch is off or the printer is in sleep mode. If the printer is in sleep mode, it will wake up automatically when it receives data or you
  • Brother International HL1060 | Users Manual - English - Page 33
    simultaneously to indicate a toner error. See "REPLACING THE TONER CARTRIDGE" in Chapter 5 and "Operator Calls" in Chapter 6. Drum Lamp The Drum lamp indicates the drum unit is nearly at the end of its life. Lamp Off r On q Printer status The drum unit can be used. The drum unit is nearly at the
  • Brother International HL1060 | Users Manual - English - Page 34
    indicates the error by blinking the Alarm lamp with another lamp or by printing an error report.  Note The Ready, Data and Drum lamps are used to indicate printer errors with the Alarm lamp. See "ALARM INDICATIONS AT A GLANCE" in Chapter 6 and take corrective action for the error. Switch If you
  • Brother International HL1060 | Users Manual - English - Page 35
    USER'S GUIDE Lamp Lit Drum Alarm Ready Data  Note • When the printer goes into sleep mode, the fan will not stop until the printer engine has cooled down. • Sleep mode allows the print engine to cool, so the temperature of your room and how long the printer has been in sleep mode affects the warm-
  • Brother International HL1060 | Users Manual - English - Page 36
    Brother Driver CHAPTER 3 CONTROL PANEL Page Protection If the printed images are too complex to print, the printer may print a partial image on the page. If this occurs, the printer the following ways. • The supplied printer driver for Windows 95/Windows 3.1 • The supplied RPC program for DOS For
  • Brother International HL1060 | Users Manual - English - Page 37
    ) APT allows your printer to produce fine gray scales to improve the appearance of documents containing photographic images. Using this feature, the image is printed in 256 shades of gray at near photographic quality. This setting can be made by using the supplied Windows driver. Also, a demo file
  • Brother International HL1060 | Users Manual - English - Page 38
    ) will only print at 300 dpi. The serial interface board is installed onto the main controller board inside the printer. For the details about installation, see the instruction guide which was provided with the serial interface board. Selecting the RS-422A (Apple) or RS-232C (IBM) Serial Interface
  • Brother International HL1060 | Users Manual - English - Page 39
    USER'S GUIDE If necessary, select the interface type as follows: 1. Make sure that the printer is in the off-line state. 2. several different places, within your DOS application, within the Windows Printer Icon (for Windows application software only), or within your AUTOEXEC.BAT file using MODE
  • Brother International HL1060 | Users Manual - English - Page 40
    CHAPTER 4 OPTIONS If necessary, set the serial interface parameters as follows: 1. Make sure that the printer is in the off-line state. 2. Set the serial interface parameters by moving up (on) or down (off) the selectors of the dual in-line
  • Brother International HL1060 | Users Manual - English - Page 41
    USER'S GUIDE Table 3: Parity Settings Selector 1 On On Off Selector 2 On Off - Parity Odd Even None  Note • The factory settings are indicated in bold. • If the robust Xon setting is turned on with selector 8, the printer sends Xon signals at one second intervals to the connected computer
  • Brother International HL1060 | Users Manual - English - Page 42
    4 OPTIONS You can connect a parallel and a serial interface cable at the same time. The auto interface selection function allows you to share the printer with two computers. To do this, connect the parallel interface cable and then connect the serial interface cable as follows: 1. Make sure that the
  • Brother International HL1060 | Users Manual - English - Page 43
    the automatic emulation switching function will work among HP LaserJet 5P, BR-Script 2 and EPSON FX-850 or HP LaserJet 5P, BR-Script 2 and IBM Proprinter XL. ! Caution Although Brother supplies two types of ROM boards, BR-2000 and BR3000, this printer supports only the BR-3000 option. You cannot use
  • Brother International HL1060 | Users Manual - English - Page 44
    Other Features".) Minimum Memory Recommendation (including resident memory) s HP LaserJet 5P, EPSON FX-850, and IBM Proprinter XL printer can also support DIB graphics with a resolution of 1200 x 600 dpi under Windows 95/Windows 3.1 with the supplied printer driver. We recommend to expand the printer
  • Brother International HL1060 | Users Manual - English - Page 45
    USER'S GUIDE The following type of SIMMs can be installed: • 1 MByte HITACHI HB56D25632B-6A, -7A • 2 MByte , you need to remove the installed 2 MB SIMM and install the new 4 MB SIMM into the printer. Installing the SIMM When you install the SIMM, follow these steps: 1. Turn off the power switch
  • Brother International HL1060 | Users Manual - English - Page 46
    the slot and push gently until it clicks into place. Fig. 4-5 Install the SIMM 5. Install the main controller board into the printer by sliding it into the guide rails. 6. Secure the main controller board with the four screws. 7. Reconnect the interface cable from your computer and plug the power
  • Brother International HL1060 | Users Manual - English - Page 47
    CHAPTER 5 MAINTENANCE CHAPTER 5 MAINTENANCE REPLACING THE TONER CARTRIDGE The printer can print approximately 2,200 pages with one toner cartridge. When the toner cartridge is running low, the Alarm and Data (Toner) lamps blink once every 5 seconds to indicate toner low.  Note • Actual page count
  • Brother International HL1060 | Users Manual - English - Page 48
    USER'S GUIDE ! Caution Keep the drum unit level after removing the toner cartridge, to avoid possible toner spill or scatter. Follow these steps to replace the toner cartridge: 1. Turn off the power switch. 2. Open the top cover. Remove the drum unit by holding each side of the drum and gently
  • Brother International HL1060 | Users Manual - English - Page 49
    , never touch the shaded parts shown in the following illustration. High Temperature Fig. 5-3 Inside the Printer 3. Gently turn the lever on the toner cartridge forward until it stops.  Note The toner cartridge cannot be removed unless the shutter is completely closed by turning the lever fully to
  • Brother International HL1060 | Users Manual - English - Page 50
    USER'S GUIDE 4. Remove the old toner cartridge from the drum unit by pulling it out gently. Fig. 5-5 Removing the Old Toner Cartridge ! Caution Handle the toner cartridge carefully. If toner scatters on your hands or clothes, wipe or wash it off with cold water immediately. 5. Unpack the new toner
  • Brother International HL1060 | Users Manual - English - Page 51
    right hand side of the drum unit. Make sure that the toner cartridge guide bar is exactly aligned with the guide slot in the drum unit to ensure that the toner cartridge and the drum unit fit together correctly. Fig. 5-7 Installing the Toner Cartridge into the Drum Unit 7. Gently turn the lever on
  • Brother International HL1060 | Users Manual - English - Page 52
    USER'S GUIDE REPLACING THE DRUM UNIT The printer uses a drum unit to create the print images on paper. If the Drum lamp is on, it indicates the drum unit is nearly at the end of its life. We recommend you prepare a new drum unit to replace the current one. Even if the Drum lamp is on, you may be
  • Brother International HL1060 | Users Manual - English - Page 53
    illustration. High Temperature Fig. 5-11 Inside the Printer 3. Remove the toner cartridge from the drum unit and keep it in a safe place. For more information, see "REPLACING THE TONER CARTRIDGE" in this chapter.  Note • Discard the used drum unit according to local regulations. If you are not
  • Brother International HL1060 | Users Manual - English - Page 54
    USER'S GUIDE Fig. 5-12 Removing the Toner Cartridge 4. Unpack the drum unit and gently shake it five or six times horizontally. Fig. 5-13 Shaking the Drum Unit ! Caution • Do not remove the starter sheet. Starter Sheet CHAPTER 5 -8 Fig. 5-14 Do Not Remove the Starter Sheet • Only unpack a drum
  • Brother International HL1060 | Users Manual - English - Page 55
    5. Install the toner cartridge into the new drum unit. For more information, see "REPLACING THE TONER CARTRIDGE" in this chapter. 6. Install the new drum unit into the printer. Fig. 5-15 Installing the Drum Unit 7. Close the top cover. 8. Turn on the power switch. The printer automatically ejects
  • Brother International HL1060 | Users Manual - English - Page 56
    USER'S GUIDE ADJUSTING THE PRINT DENSITY The print density dial is located inside the printer. You can use it to adjust the amount of toner applied to the paper. When the toner cartridge and drum unit are replaced, or if the operating temperature and humidity are high or low, print conditions may
  • Brother International HL1060 | Users Manual - English - Page 57
    exterior and interior periodically. If printed pages get stained with toner, clean the printer interior and drum unit. Cleaning the Printer Exterior Clean the printer exterior as follows: 1. Turn off the power switch and unplug the power cord. Warning There are high voltage electrodes inside the
  • Brother International HL1060 | Users Manual - English - Page 58
    USER'S GUIDE Cleaning the Printer Interior and Drum Unit Clean the printer interior and the drum unit as follows: 1. Turn off the power switch and unplug the power cord. Warning There are high voltage electrodes inside the printer. Before cleaning the printer, make sure to turn off the power switch
  • Brother International HL1060 | Users Manual - English - Page 59
    ! Caution • Do not touch the scanner window with your finger. • Do not wipe the scanner window with cleaning alcohol (isopropyl). 5. Turn the drum unit upside down carefully. ! Caution Handle the drum unit carefully as it contains toner. If toner scatters and your hands or cloths get dirty, wipe
  • Brother International HL1060 | Users Manual - English - Page 60
    USER'S GUIDE 6. Clean the primary corona wire inside the drum unit by gently sliding the tab to the right and left several times. Home Position (v) Fig. 5-23 Cleaning the Primary Corona Wire 7. Return the tab to the home position (v mark position) before reinstalling drum unit. ! Caution Be sure to
  • Brother International HL1060 | Users Manual - English - Page 61
    CHAPTER 5 MAINTENANCE Cleaning the Paper Feed Rollers Clean the paper feed rollers inside the multi-purpose sheet feeders with a clean cloth as shown below:. 1. Cleaning the Feeder 1 paper feed rollers. Fig. 5-24 Cleaning the Feeder 1 Paper Feed Rollers 2. Cleaning the Feeder 2 paper feed rollers.
  • Brother International HL1060 | Users Manual - English - Page 62
    . 1. Turn off the power switch and unplug the printer from the AC outlet. 2. Open the top cover. 3. Remove the drum unit assembly, referring to the previous section.  Note Remove the drum unit assembly with the toner cartridge included. Fig. 5-26 Removing the Drum Unit Assembly CHAPTER 5 -16
  • Brother International HL1060 | Users Manual - English - Page 63
    the original Styrofoam packing material. 7. Place any documents (manual and any documentation describing the reason for repacking printer), and drum unit assembly in the carton box as shown below. 8. Close the carton box and tape it. Manuals Dust Cover Printer Drum Unit Including Toner Cartridge
  • Brother International HL1060 | Users Manual - English - Page 64
    the panel switch. Reinstall the paper and press the panel switch. Indicates that the printer has approximately 100 pages of printing left before the toner cartridge is empty. Prepare a new toner cartridge. Toner Empty Replace the toner cartridge with a new one referring to Chapter 5. CHAPTER 6 -1
  • Brother International HL1060 | Users Manual - English - Page 65
    USER'S GUIDE For errors shown below, the printer indicates an operator call by blinking the Alarm lamp. If you use the printer with the supplied Windows driver, the status monitor will appear to indicate the error on your computer screen. The printer also prints some error messages on paper. Error
  • Brother International HL1060 | Users Manual - English - Page 66
    be damaged. Consult your dealer.  Note If the printer does not operate as you expect it to, it is recommended that you turn off the power switch, wait a few seconds and then turn it on again. If you still have problems, consult your dealer or our authorized service representative. CHAPTER 6 -3
  • Brother International HL1060 | Users Manual - English - Page 67
    USER'S GUIDE Service Calls If an unrecoverable error occurs, the printer indicates the need for a service call by lighting all the lamps and then the following combination of lamps alternately: Service Call Feeder Drum Alarm Ready Data Fuser malfunction r q r r r Laser BD malfunction r r q r r
  • Brother International HL1060 | Users Manual - English - Page 68
    TROUBLESHOOTING Before you can clear a paper jam error, you need to find the location of the paper jam. Locate the position referring to the following figure. Paper Paper Front Multi-Purpose Sheet Feeder 1 can be removed to clear paper jams Rear Multi-Purpose Sheet Feeder 2 Top Cover Drum Unit
  • Brother International HL1060 | Users Manual - English - Page 69
    piece of paper does not remain inside the printer: refer to the following sections. Feeder 1 Feeder 2 Fig. 6-3 Paper Jam in the Feeders If the paper cannot be pulled up, see the next sections "Paper Jam under Feeder 1" and "Paper Jam near the Drum Unit." t Paper Jam under Feeder 1 If a paper jam
  • Brother International HL1060 | Users Manual - English - Page 70
    6 TROUBLESHOOTING t Paper Jam near the Drum Unit If a paper jam has occurred near the drum unit, open the top cover and remove the drum unit. ( Œ ) Then, pull the jammed paper upwards slowly and out of the printer. (  ) Install the drum unit and close the top cover. Fig. 6-5 Paper Jam near the Drum
  • Brother International HL1060 | Users Manual - English - Page 71
    USER'S GUIDE ! Caution Do not pull jammed paper from the output tray. Be sure to open the top cover to remove the jam, or the fuser may get dirty with toner powder and may result in toner scatter on the next printed page or pages. Fig. 6-7 Do Not Pull the Jammed Paper from the Output
  • Brother International HL1060 | Users Manual - English - Page 72
    have been removed. • The toner cartridge and drum unit are installed properly. • The interface cable is securely connected between the printer and computer. • Check to see if the Alarm lamp is blinking. If the lamp is blinking, refer to the Operator Call section of this manual. • Check to see if
  • Brother International HL1060 | Users Manual - English - Page 73
    USER'S GUIDE Setting Up the Printer for Windows Question I cannot print from my application software. Sometimes I get a Print Overrun error when printing certain documents from Windows. Sometimes I get the Memory Full message. How can I correct this? Recommendation • Make sure the supplied
  • Brother International HL1060 | Users Manual - English - Page 74
    select the HP LaserJet 5P printer in your application software. Press the panel switch. The data has been sent to the printer but the printer did not receive the Page Eject command: print screens do not send this command. This was a common problem with database software and spreadsheet software when
  • Brother International HL1060 | Users Manual - English - Page 75
    USER'S GUIDE Setting Up the Printer for Apple Macintosh Computers When Using the Optional RS-100M Serial Interface Question I cannot print from my application software. Recommendation • Make sure that the supplied Macintosh printer driver is installed in the System Folder and it is selected with
  • Brother International HL1060 | Users Manual - English - Page 76
    CHAPTER 6 TROUBLESHOOTING Paper Handling Question The printer does not load paper. The printer does not load paper from the manual feed slot. How from either the multi-purpose sheet feeder 1 or the manual feed slot. Your application software must be set up correctly to print on the envelope size
  • Brother International HL1060 | Users Manual - English - Page 77
    of the page. This may be solved by the following ways. • If you are using Windows 3.1 with the supplied printer driver, change the following settings in the driver and try again. Graphics Mode TrueType™ Mode Use Printer TrueType™ Font • Set the page protection mode to "AUTO" or your document size
  • Brother International HL1060 | Users Manual - English - Page 78
    the primary corona wire of the toner cartridge. See "Cleaning the Printer Interior and Drum Unit" in Chapter 5. • Make sure that the tab of the corona wire is at the home position. If you still have the same problem and the Drum lamp is on after cleaning, replace the drum unit with a new one. Fig
  • Brother International HL1060 | Users Manual - English - Page 79
    the same problem and the Drum lamp is on after cleaning, replace the drum unit with a new one. Fig. 6-12 Black Page Nothing is printed on the page. • Make sure that the toner cartridge is not empty. • Wipe the electric terminals referring to "Cleaning the Printer Interior and Drum Unit" in Chapter
  • Brother International HL1060 | Users Manual - English - Page 80
    surface. • Remove the drum unit with the toner cartridge installed. Try shaking them from side to side. • You may clear the problem by wiping the scanner windows with a soft cloth. (See "Cleaning the Printer Interior and Drum Unit.") If the same problem occurs after cleaning and Drum lamp is still
  • Brother International HL1060 | Users Manual - English - Page 81
    APPENDIX A APPENDIX PRINTER SPECIFICATIONS Printing Print Method Electrophotography by semiconductor laser beam scanning Laser Resolution Wavelength: 780 nm Output: 5 mW max 1200 (H) x 600 (V) dots/inch (for Windows DIB graphics) 600 x 600 dots/inch (for Windows and DOS) 300 x 300 dots/inch (
  • Brother International HL1060 | Users Manual - English - Page 82
    and toner that you use, the number of pages per print job, etc.. Functions Emulation Brother Printing Solution for Windows Automatic emulation selection among HP LaserJet 5P, EPSON FX-850 or IBM Proprinter XL Printer Driver Windows 3.1/3.11 and Windows 95 driver, supporting Brother Printing
  • Brother International HL1060 | Users Manual - English - Page 83
    85% (without condensation) Dimensions (W x D x H) 402 x 439 x 274 mm (15.8 x 17.3 x 10.8 inches) (when the output tray is closed.) Weight Approx. 9.6 kg (21.2 lb.) including the drum unit and toner cartridge APPENDIX A -3
  • Brother International HL1060 | Users Manual - English - Page 84
    USER'S GUIDE PARALLEL INTERFACE SPECIFICATIONS  Note To ensure the highest quality performance, it is recommended that you use an IEEE 1284 compliant parallel cable between the printer and your computer. Only IEEE 1284 cables support all of the advanced printing capabilities, such as bi-
  • Brother International HL1060 | Users Manual - English - Page 85
    APPENDIX  Note To use bi-directional communication, an interface cable which has the pin connections above must be used. Pin 1 18 2 19 3 4 20 5 6 21 7 8 22 9 10 24 11 23 12 13 14 25 16 15 17 Shield Pin 1 19 2 20 3 21 4 22 5 23 6 24 7 25 8 26 9 27 10 28 11 29 12 17 13 15 14 30 31 33 32 34 36 35 18
  • Brother International HL1060 | Users Manual - English - Page 86
    USER'S GUIDE RESIDENT FONTS Bitmapped Fonts This printer has the following bitmapped fonts. They can be used in the HP LaserJet 5P, EPSON FX-850, Bold, BoldOblique) • Utah Condensed (Oblique, Bold, BoldOblique) Microsoft Windows 3.1 TrueType Compatible Fonts • BR Symbol • Helsinki (Oblique, Bold,
  • Brother International HL1060 | Users Manual - English - Page 87
    APPENDIX s The following scalable fonts can be used in the BR-Script mode. ( Only when you have installed the BR-Script 2 ROM board.) Atlanta Book (BookOblique, Demi, DemiOblique) BR Dingbats BR Symbol Brougham (Oblique, Bold, BoldOblique) Brussels Light (LightItalic, Demi, DemiItalic) Calgary
  • Brother International HL1060 | Users Manual - English - Page 88
    USER'S GUIDE SYMBOL SETS/ CHARACTER SETS OCR Symbol Sets When the OCR-A or OCR-B font is selected, the corresponding symbol set is always used. • OCR-A • OCR-B HP (8M) • Pi Font (15U) • MS Publishing (6J) • Windows 3.0 (9U) • Desktop (7J) • MC Text (12J) • Printer Console Program. APPENDIX A -8
  • Brother International HL1060 | Users Manual - English - Page 89
    4-3 DIP switch 1-2, 4-3 DOS 6-11 dpi 1-3 Drum lamp 3-2 drum unit 5-6 life A-2 DTR 4-3 duplex printing 2-9 E economy mode 1-5 emulation 1-4, A-2 envelope 2-1 error message 6-2 recoverable 6-1 unrecoverable 6-4 extension support wire 1-2 F Factory Reset 3-4 Feeder lamp 3-2 H hex
  • Brother International HL1060 | Users Manual - English - Page 90
    printer driver A-2 printer status monitor 1-4 protocol 4-3 R Ready lamp 3-1 Remote Printer Console 1-4 resolution 1-3, A-1 robust 4-3 RPC 1-4 RS-232C 4-2 RS-422A 4-2 S scalable font A-6 scanner window 5-13 serial interface 4-1 cable 4-4 parameter 4-3 RS-422A/RS-232C port 1-2 service
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
I
Please read this manual thoroughly before using the printer.
Brother Laser Printer
HL-1060 Series
User’s Guide
Keep this manual in a convenient place for quick and easy reference at all times.