Brother International LB7000 Operation Manual - Page 15

Caution

Get Brother International LB7000 PDF manuals and user guides View all Brother International LB7000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

Winding/Installing the Bobbin Adjusting input sensitivity for operation keys You can adjust the sensitivity of the operation keys to 5 levels. Display the settings screen to set desired level. Press a to display the settings screen. Display page 7 by pressing / . b Press [Start]. c Winding/Installing the Bobbin CAUTION • Only use the plastic bobbin that comes with this machine or bobbins of the same type (SA156/SFB: XA5539-151/SFB). The bobbin's height is 11.5 mm (approx. 7/16 inch). Using other bobbins may cause damage to the machine. SA156 is Class 15 type bobbin. 1 GETTING READY Winding the bobbin This section describes how to wind thread onto a bobbin. → The adjusting screen is displayed. Adjust the [Input Sensitivity] by pressing / . d • The higher the setting, the more sensitive the keys will be. The default setting is [3]. • We recommend selecting the highest setting if an electrostatic touch pen is being used. • While adjusting the input sensitivity, press to check whether the key responds. When the key responds, the setting value indicating the sensitivity blinks. Press e to return to previous screen. ■ If the machine does not respond when an operation key is pressed Turn machine off, then hold down (Thread cutter button) and turn on the machine to reset [Input Sensitivity]. Display the settings screen, and then adjust the [Input Sensitivity] again. Memo • When winding the bobbin for sewing utility stitches, use thread appropriate for the fabric that you wish to sew (page 21). Normally, the thread will be the same as what is used for the upper threading. • When winding bobbin for embroidery, be sure to use the recommended 60 weight embroidery bobbin thread for this machine. Place the bobbin on the bobbin winder shaft so that the a notch in the bobbin aligns with the spring on the shaft, and then slide the bobbin winder shaft to the right until it snaps into place. • The "Start/Stop" button lights up in orange. 1 Notch 1 2 Bobbin winder shaft spring 2 Remove the spool cap and place the spool of thread for b the bobbin onto the spool pin. Slide the spool onto the spool pin so that the thread unwinds to the front from the bottom. Otherwise the thread may become tangled around the spool pin. 1 1 The thread unwinds to the front from the bottom. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Winding/Installing the Bobbin
GETTING READY
13
1
Adjusting input sensitivity for operation keys
You can adjust the sensitivity of the operation keys to 5 levels.
Display the settings screen to set desired level.
a
Press
to display the settings screen.
b
Display page 7 by pressing
/
.
c
Press
[
Start
]
.
→
The adjusting screen is displayed.
d
Adjust the
[
Input Sensitivity
]
by pressing
/
.
•
The higher the setting, the more sensitive the keys
will be. The default setting is [3].
•
We recommend selecting the highest setting if an
electrostatic touch pen is being used.
•
While adjusting the input sensitivity, press
to
check whether the key responds.
When the key responds, the setting value indicating
the sensitivity blinks.
e
Press
to return to previous screen.
■
If the machine does not respond when an
operation key is pressed
Turn machine off, then hold down
(Thread cutter
button) and turn on the machine to reset [Input
Sensitivity]. Display the settings screen, and then adjust
the [Input Sensitivity] again.
Winding the bobbin
This section describes how to wind thread onto a bobbin.
a
Place the bobbin on the bobbin winder shaft so that the
notch in the bobbin aligns with the spring on the shaft,
and then slide the bobbin winder shaft to the right until
it snaps into place.
•
The “Start/Stop” button lights up in orange.
b
Remove the spool cap and place the spool of thread for
the bobbin onto the spool pin.
Slide the spool onto the spool pin so that the thread
unwinds to the front from the bottom. Otherwise the
thread may become tangled around the spool pin.
1
The thread unwinds to the front from the bottom.
Winding/Installing the Bobbin
CAUTION
•
Only use the plastic bobbin that comes with
this machine or bobbins of the same type
(SA156/SFB: XA5539-151/SFB). The bobbin's
height is 11.5 mm (approx. 7/16 inch). Using
other bobbins may cause damage to the
machine. SA156 is Class 15 type bobbin.
Memo
•
When winding the bobbin for sewing utility stitches, use
thread appropriate for the fabric that you wish to sew
(page 21). Normally, the thread will be the same as what
is used for the upper threading.
•
When winding bobbin for embroidery, be sure to use the
recommended 60 weight embroidery bobbin thread for
this machine.
1
Notch
2
Bobbin winder
shaft spring
2
1
1