Brother International LK3-B434E MKII Instruction Manual - English - Page 59

Changing Special Functions Using The Memory Switches, Memory Switches 10 - 1f

Get Brother International LK3-B434E MKII PDF manuals and user guides View all Brother International LK3-B434E MKII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES s Memory switches 10 - 1F Switch Motion when set to ON memo-10 - - memo-11 memo-12 Pneumatic wiper can be used. (Pneumatic wiper is available by special order.) memo-13 The inner clamping device moves forward at the 1/4-way mark and returns at the 3/4-way mark for the pattern being sewn. memo-14 Solenoid wiper can be used. When using the inner clamping device, shunting to prevent interference memo-15 between the inner clamping device and the needle is not carried out after the sewing end. memo-16 memo-17 memo-18 memo-19 memo-1A Needle cooler output is enabled. (Needle cooler is available by special order.) Thread take-up device is not operated at the sewing end. Thread take-up device operates one stitch before the sewing end. For solenoid specifications, presser position errors are not detected. Needle up stop position errors are not detected. Presser can be moved up and down before the home position is detected. memo-1b (Normally the presser cannot be moved up and down until after the home position has been detected.) memo-1c memo-1d memo-1E memo-1F - For pneumatic specifications, the air pressure detection switch is enabled. (The air pressure sensor is a special-order option.) Errors can be reset using the EMERGENCY STOP switch. Thread is not trimmed when an emergency stop occurs during sewing. Initial value Solenoid Pneumatic -- -- -- -- -- -- -- ON -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- s Memory switches 20 - 2F Switch Motion when set to ON memo-20 memo-21 memo-22 memo-23 memo-24 memo-25 memo-2F Machine head from previous B430E series is used. (Only the operation panel and box are Mark II.) Rotating-type thread breakage detector operates. (Device is available by special order.) During thread breakage detection, sensitivity is decreased from 8 to 14 stitches at the sewing start. (Sensitivity during sewing is three stitches.) When DIP switch A-8 is simultaneously ON, setting values changed using the operation panel are ignored. The lower thread sensor operates. (The lower thread sensor is a specialorder option.) - Initial value Solenoid Pneumatic -- -- -- -- -- -- -- -- -- -- -- -- 53 LK3-B434E Mark II

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
53
LK3-B434E Mark II
13. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES
■
Memory switches 10 - 1F
■
Memory switches 20 - 2F
memo-10
-
memo-11
memo-12
memo-13
memo-14
memo-15
memo-16
memo-17
memo-18
memo-19
memo-1A
memo-1b
memo-1c
memo-1d
memo-1E
memo-1F
Solenoid
Pneumatic
--
--
--
ON
--
--
--
--
--
--
--
--
--
--
--
Initial value
--
--
--
--
--
--
--
--
--
--
--
--
--
--
--
Motion when set to ON
–
Pneumatic wiper can be used. (Pneumatic wiper is available by special
order.)
The inner clamping device moves forward at the 1/4-way mark and returns
at the 3/4-way mark for the pattern being sewn.
Solenoid wiper can be used.
When using the inner clamping device, shunting to prevent interference
between the inner clamping device and the needle is not carried out after
the sewing end.
Needle cooler output is enabled. (Needle cooler is available by special
order.)
Thread take-up device is not operated at the sewing end.
Thread take-up device operates one stitch before the sewing end.
For solenoid specifications, presser position errors are not detected.
Needle up stop position errors are not detected.
Presser can be moved up and down before the home position is detected.
(Normally the presser cannot be moved up and down until after the home
position has been detected.)
–
For pneumatic specifications, the air pressure detection switch is enabled.
(The air pressure sensor is a special-order option.)
Errors can be reset using the EMERGENCY STOP switch.
Thread is not trimmed when an emergency stop occurs during sewing.
Switch
memo-20
memo-21
memo-22
memo-23
memo-24
memo-25
-
memo-2F
Solenoid
Pneumatic
--
--
--
--
--
--
Initial value
--
--
--
--
--
--
Motion when set to ON
Machine head from previous B430E series is used. (Only the operation
panel and box are Mark II.)
Rotating-type thread breakage detector operates. (Device is available by
special order.)
During thread breakage detection, sensitivity is decreased from 8 to 14
stitches at the sewing start. (Sensitivity during sewing is three stitches.)
When DIP switch A-8 is simultaneously ON, setting values changed using
the operation panel are ignored.
The lower thread sensor operates. (The lower thread sensor is a special-
order option.)
–
Switch