Brother International LK3-B438E MKII Instruction Manual - English - Page 26

CHECKING THE SEWING PATTERN, When DIP switch 7 is

Get Brother International LK3-B438E MKII PDF manuals and user guides View all Brother International LK3-B438E MKII manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

6. CHECKING THE SEWING PATTERN s When checking by operating only the feed mechanism 6. CHECKING THE SEWING PATTERN 1. Turn on the power switch. (The POWER indicator will illuminate and the program number will flash in the display window.) 2. Set the X-scale and Y-scale in accordance with the hole pitch of the buttons being used. (Refer to "5-2-2. Setting the X-scale and Y-scale".) 3. Set the button. (Refer to "7-7. Inserting the button".) 4. Press the TEST switch. (The TEST indicator will illuminate.) TEST 5. Depress the foot switch to the second step. Only the feed mechanism will move. ( The feed mechanism moves forward by one stitch each time the foot switch is depressed. Each time the feed mechanism is moved forward by one stitch, turn the machine pulley by hand and check that the needle goes into the holes in the button without touching the button. Do this for each hole position. (NOTE) After checking is complete, depress the foot switch to move the feed mechanism to the 1st step 2nd step ) end position. * If you depress the foot switch again and keep it depresses after the feed mechanism has started to move, the feeding speed will increase. * If you would like to stop the feed while it is moving, press the TEST switch. 6. Press the TEST switch. (The TEST indicator will switch off and the test mode will be cleared.) TEST 7. Depress the foot switch. The work clamp will rise and the preparation for sewing will be completed. NOTE: If the needle touches the button, carry out the following. 1. Check that the needle size correctly matches the diameter of the holes in the button. (Refer to "7-1. Selecting the needle and thread".) 2. Make fine adjustments to the X-scale and Y-scale. (Refer to "5-2-2. Setting the X-scale and Y-scale".) 3. Adjust the position of the button holder. (Refer to "10-10. Adjusting the position of the button holder".) To ensure safety during use ...... You can prevent accidental changes being made to programs by setting DIP switches 7 and 8 to ON. When DIP switch 7 is ON ... The sewing pattern cannot be enlarged. When DIP switch 8 is ON ... The program number cannot be changed. LK3-B438E Mark II 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
LK3-B438E Mark II
20
1. Turn on the power switch.
(The POWER indicator will illuminate and the program number will flash in the display window.)
4. Press the TEST switch.
(The TEST indicator will illuminate.)
5. Depress the foot switch to the second step.
Only the feed mechanism will move.
The feed mechanism moves forward by one stitch each time the foot switch is depressed.
Each time the feed mechanism is moved forward by one stitch, turn the machine pulley
by hand and check that the needle goes into the holes in the button without touching the
button. Do this for each hole position. (NOTE)
After checking is complete, depress the foot switch to move the feed mechanism to the
end position.
*
If you depress the foot switch again and keep it depresses after the feed mechanism has started to
move, the feeding speed will increase.
*
If you would like to stop the feed while it is moving, press the TEST switch.
6. Press the TEST switch.
(The TEST indicator will switch off and the test mode will be cleared.)
7. Depress the foot switch.
The work clamp will rise and the preparation for sewing will be completed.
TEST
TEST
1st step
2nd step
6. CHECKING THE SEWING PATTERN
■
When checking by operating only the feed mechanism
To ensure safety during use
......
You can prevent accidental changes being made to
programs by setting DIP switches 7 and 8 to ON.
When DIP switch 7 is ON
... The sewing pattern cannot be enlarged.
When DIP switch 8 is ON
... The program number cannot be changed.
6. CHECKING THE SEWING PATTERN
2. Set the X-scale and Y-scale in accordance with the hole pitch of the buttons being used.
(Refer to “5-2-2. Setting the X-scale and Y-scale”.)
3. Set the button.
(Refer to “7-7. Inserting the button”.)
NOTE: If the needle touches the button, carry out the following.
1.Check that the needle size correctly matches the diameter of the holes in the button. (Refer to “7-1. Selecting the
needle and thread”.)
2.Make fine adjustments to the X-scale and Y-scale. (Refer to “5-2-2. Setting the X-scale and Y-scale”.)
3.Adjust the position of the button holder. (Refer to “10-10. Adjusting the position of the button holder”.)
(
)