Brother International LS-2000 Quick Setup Guide - English - Page 2

Winding the Bobbin 1 2 Threading the Needle 1 Pass the thread through the hole Pull up on the thread spool pin to lengthen the height. Place the thread spool on the pin on the bobbin from inside. Use and pass the thread around the bobbin winder pre-tension disc. upper hole, not both. Place on bobbin shaft and slide to the right. 2 3 4 CAUTION Not winding the bobbin properly may cause the thread tension to loosen, and may break the needle. Raise the presser foot lifter. 3 4 While holding the end of the thread, When the bobbin starts to spin press the foot controller to begin slowly and becomes full, release winding the thread. Cut the thread the foot controller. Cut the thread, from the top and proceed winding. slide the bobbin winding shaft to 1 2 the left and remove the bobbin. Inserting the Bobbin 1 Wound evenly 2 Wound poorly 1 3 4 Raise the needle to its highest position and remove the bobbin case by pulling the latch. 2 Hold the bobbin case as shown. Insert the bobbin with the thread coming from the bottom toward the top and the thread tail hanging out of the bobbin case. Pull the trailing thread through the slot, down and to the left, until it enters the delivery eye under the tension spring. CAUTION: Make sure you set the bobbin so the thread unrolls in the right direction. If the thread unrolls in the wrong direction, it may cause the thread tension to be incorrect or break the needle. Holding the bobbin case by the latch, align your finger with the top opening of the shuttle race, insert the case into the shuttle race and release the latch. Raise the thread take-up lever to its highest position by turning the handwheel. Place the thread spool on the spool pin. (Don't forget to pull up the pin) Pass the thread through the thread guide and down the right channel on the front of the machine. 5 6 Pass the thread into the thread tension discs or behind the thread tension dial from the right to the left. 7 Grasp the thread on both sides of the tension disc and pull to ensure it is in place. 8 Guide the thread up the left channel, clear to the back of the opening around the take-up lever and back down the left side of the channel to thread the take-up lever. Thread the needle from front to back and pull out about 5 cm (2 inches) of thread. Cleaning the Bobbin Case 1 Remove the power plug from the outlet. 2 3 4 Raise the needle to its highest position, Slide the latch levers out from the pull the latch and remove the bobbin retaining ring. case. 5 6 Remove the retaining ring. 7 Relative Chart of Sewing Fabrics, Needles and Thread Combinations Very Thin Sewing Fabrics Fine tricot, Fine lace, Thin linen, Silk, Organza, Chiffon Needle Sizes #65/9 Lightweight Voile, Taffeta, Synthetics, Silk, Batiste #75/11 Medium Weight Heavyweight Cotton, Gingham, Poplin, Percale, Pique, Satin, Velvet, Lightweight wool, Fine corduroy, Suitings, Linen, Muslin Denim, Gabardine, Tweed, Corduroy, Canvas, Duck #90/14 (Supplied with your machine) #100/16 Knits Single knit, Double knit, Jersey, Tricot #90/14 (Ball point) Thread Sizes Cotton: 80 Synthetic/Polyester Long Fiber Fine Mercerized Cotton Cotton: 60-80 Silk: "A" Synthetic/Polyester Long Fiber Mercerized 50 Cotton: 50-60 Silk: "A" Synthetic/Polyester Long Fiber Mercerized 50-60 Cotton: 40-50 Mercerized Heavy Duty Polyester Long Fiber Cotton Wrapped Polyester Polyester Long Fiber Uses common replacement accessories: Bobbin: Class 15 Needle: Standard sewing machine needles Light Bulb: Small screw base sewing machine bulb Remove the hook by grasping the center Remove any accumulated lint and post and pulling out. Note its position thread with a brush. related to the driver. 8 9 Grasp the center post of the hook, match the hook position opposite the driver and insert. Utiliza accesorios comunes de remplazo: Carretel: Clase 15 Agujas: Agujas estándares para máquina de coser. Bombilla: Para máquina de coser con base roscada pequeña Insert the retaining ring with the notch up. Push the latch levers into their locked position. Replace the bobbin case. Toll Free Phone 877-276-8437