Brother International MFC 1970MC Users Manual - English - Page 110

PC Configuration Requirements, Connecting MFC 1870MC or MFC 1970MC to Your PC

Page 110 highlights

102 C H A P T E R T H I R T E E N PC Configuration Requirements Your PC must meet or exceed the follwing minimum system configuration requirements for you to install and use Multi-Function Link: CPU 80486/66 or higher RAM 8MB or greater for Windows® 3.1 or 3.11 8MB or greater for Windows® 95 (16MB recommended) 16MB or greater for Windows NT® Workstation Version 4.0 (32MB recommended) Hard Disk Drive 50MB Operating System Windows® 3.1, 3.11, 95 or NT® Workstation Version 4.0 Port Available Serial port CD-Rom Drive Connecting MFC 1870MC or MFC 1970MC to Your PC Follow the instructions below to hook up the Multi-Function Link Cable. 1 Position your Brother MFC near your personal computer CPU (maximum distance of approximately 5-6 feet). 2 Make sure the power to the PC is switched off and the MFC is unplugged. 3 Connect the RJ-8 connector of the Multi-Function Link Cable to the side of your Brother MFC in the jack labeled PC I/F. 4 Connect the 25-pin female RS-232 connector of the Multi-Function Link Cable to your PC in the available male serial communications port. Use the 9-pin adapter if your PC requires it. (See your PC owner's manual for the correct interface port for connection.) NOTE: If your PC is an IBM Aptiva, and MWAVE card is using COM1. You must connect the Multi-Function Link Cable to another COM serial port that is available. or

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136

102
CHAPTER THIRTEEN
PC Configuration Requirements
Your PC must meet or exceed the follwing minimum system configuration
requirements for you to install and use Multi-Function Link:
CPU
80486/66 or higher
RAM
8MB or greater for Windows
®
3.1 or 3.11
8MB or greater for Windows
®
95 (16MB recommended)
16MB or greater for Windows NT
®
Workstation
Version 4.0 (32MB recommended)
Hard Disk Drive
50MB
Operating System
Windows
®
3.1, 3.11, 95 or NT
®
Workstation Version 4.0
Port
Available Serial port
CD-Rom Drive
Connecting MFC 1870MC or MFC
1970MC to Your PC
Follow the instructions below to hook up the Multi-Function Link Cable.
1
Position your Brother MFC near your personal computer CPU (maximum
distance of approximately 5-6 feet).
2
Make sure the power to the PC is switched off and the MFC is unplugged.
3
Connect the RJ-8 connector of the Multi-Function Link Cable to the side of
your Brother MFC in the jack labeled
PC I/F
.
4
Connect the 25-pin
female
RS-232 connector of the Multi-Function Link
Cable to your PC in the available
male
serial communications port.
Use the
9-pin adapter if your PC requires it.
(See your PC owner
s manual for the
correct interface port for connection.)
NOTE: If your PC is an IBM
Aptiva, and MWAVE card is using COM1.
You must connect the
Multi-Function Link Cable to another COM serial port that is
available
.
or