Campbell Scientific HFP01SC HFP01SC Hukseflux Self-Calibrating Soil Heat Flux - Page 18

Campbell Scientific HFP01SC Manual

Get Campbell Scientific HFP01SC PDF manuals and user guides View all Campbell Scientific HFP01SC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Model HFP01SC Self-Calibrating Soil Heat Flux Plate ;Stop filtering data. ; 12: If time is (P92) 1: 39 Minutes (Seconds --) into a 2: 180 Interval (same units as above) 3: 30 Then Do 13: Do (P86) 1: 28 Set Flag 8 Low ;Compute in-situ calibration. ; 14: Z=X (P31) 1: 2 X Loc [ shf_mV ] 2: 6 Z Loc [ mV_end ] 15: Z=X*Y (P36) 1: 7 X Loc [ V_Rf ] 2: 7 Y Loc [ V_Rf ] 3: 3 Z Loc [ cal ] 16: Z=X*F (P37) 1: 3 X Loc [ cal ] 2: 128.7 F 3: 3 Z Loc [ cal ] 17: Z=X+Y (P33) 1: 4 X Loc [ mV_0 ] 2: 6 Y Loc [ mV_end ] 3: 9 Z Loc [ work ] 18: Z=X*F (P37) 1: 9 X Loc [ work ] 2: .5 F 3: 9 Z Loc [ work ] 19: Z=X-Y (P35) 1: 9 X Loc [ work ] 2: 5 Y Loc [ mV_180 ] 3: 9 Z Loc [ work ] 20: Z=ABS(X) (P43) 1: 9 X Loc [ work ] 2: 9 Z Loc [ work ] 21: Z=X/Y (P38) 1: 3 X Loc [ cal ] 2: 9 Y Loc [ work ] 3: 3 Z Loc [ cal ] 22: End (P95) 23: End (P95) End Program -Input Locations1 shf 2 shf_mV 3 cal 4 mV_0 5 mV_180 6 mV_end 7 V_Rf 8 shf_mV_a 9 work 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Model HFP01SC Self-Calibrating Soil Heat Flux Plate
;Stop filtering data.
;
12:
If time is (P92)
1: 39
Minutes (Seconds --) into a
2: 180
Interval (same units as above)
3: 30
Then Do
13:
Do (P86)
1: 28
Set Flag 8 Low
;Compute in-situ calibration.
;
14: Z=X (P31)
1: 2
X Loc [ shf_mV
]
2: 6
Z Loc [ mV_end
]
15:
Z=X*Y (P36)
1: 7
X Loc [ V_Rf
]
2: 7
Y Loc [ V_Rf
]
3: 3
Z Loc [ cal
]
16:
Z=X*F (P37)
1: 3
X Loc [ cal
]
2: 128.7 F
3: 3
Z Loc [ cal
]
17:
Z=X+Y (P33)
1: 4
X Loc [ mV_0
]
2: 6
Y Loc [ mV_end
]
3: 9
Z Loc [ work
]
18:
Z=X*F (P37)
1: 9
X Loc [ work
]
2: .5
F
3: 9
Z Loc [ work
]
19:
Z=X-Y (P35)
1: 9
X Loc [ work
]
2: 5
Y Loc [ mV_180
]
3: 9
Z Loc [ work
]
20:
Z=ABS(X) (P43)
1: 9
X Loc [ work
]
2: 9
Z Loc [ work
]
21:
Z=X/Y (P38)
1: 3
X Loc [ cal
]
2: 9
Y Loc [ work
]
3: 3
Z Loc [ cal
]
22:
End (P95)
23:
End (P95)
End Program
-Input Locations-
1 shf
2 shf_mV
3 cal
4 mV_0
5 mV_180
6 mV_end
7 V_Rf
8 shf_mV_a
9 work
12