Canon 2171B002 iP4500 series Easy Setup Instructions - Page 1
Canon 2171B002 Manual
View all Canon 2171B002 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Start Here Easy Setup Instructions Unpack the Printer • Please confirm the included items against the illustration printed on the lid of the packing box. • A USB cable is necessary to connect the printer with your computer. 1 Prepare the Printer a Place the printer on a flat and horizontal surface, and do not place any objects in front of the printer. Open the Rear Tray and extend the Paper Support Extension. Press the Open button to open the Paper Output Tray, and extend the Paper Output Tray Extension. Caution Before turning on the printer, remove all the shipping tapes. d Open the Top Cover. The Print Head Holder moves to the center. Top Cover e Open the Inner Cover. 2 Install the Print Head a Remove the Print Head from its package. Caution There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. b Remove the orange protective cap from the Print Head and discard it. Electrical Contacts Print Head Nozzles b Plug the power cord in the back of the printer and connect the other end to the wall outlet. Inner Cover Protective Cap Note Do not touch the print head nozzles and the electrical contacts. c Firmly raise the Print Head Lock Lever until it stops. The Print Head Lock Lever may feel heavy. Important • Do not connect the USB cable until after the software is installed. • Plug the power cord all the way in, since it may be difficult to plug. c Press the POWER button to turn on the printer. d Insert the Print Head. Do not touch! e Push the Print Head to hold it in place, and lower the Print Head Lock Lever carefully. Photo Printer Important When cleaning the exterior of the printer, use a soft cloth to wipe it gently. For details, refer to "Cleaning Your Printer" in the Quick Start Guide. 3 Install the Ink Tanks 4 Load Printing Paper Note For the ink tanks compatible with this printer, refer to the back cover of the Quick Start Guide. a Pull the orange tape in the direction of the arrow to peel off the protective film and remove the film completely. If the air hole is blocked with the remaining film, ink may leak out or may not eject properly. b Twist off and discard the orange protective cap located on the bottom of the ink tank. Do not press! Protective Cap Ink Port Electrical Contacts Important • Do not touch the electrical contacts. • Do not touch the ink port. c Insert the ink tank into the right-hand slot and press the mark on the ink tank until it clicks into place. Important Once you have installed the ink tanks, the POWER lamp will flash green. Wait for about 2 minutes, until the POWER lamp stops flashing and changes to steady, non-flashing green and the printer has stopped making operating noises, before proceeding. a Pinch the Paper Guide and slide it to the left end. Load two sheets of supplied paper (MP-101) loaded with the printing side (whiter side) facing UP in the Rear Tray, align the paper with the right side of the Cover Guide, then slide the Paper Guide against the paper stack. Paper Guide Print Side Cover Guide Hardware setup is complete. Cassette Loading You can load paper in both the Rear Tray and Cassette. Note At purchase, the printer is set to feed from the Rear Tray. a Pull out the cassette from the bottom of the printer. Cassette d Make sure the ink lamp lights red. Install all ink tanks in order from right to left according to the colored label. e Close the Inner Cover and the Top Cover. Cover b Remove the cover of the cassette. c For A5 or larger sized paper, pull the tab towards you to unlock and extend the cassette. Tab A5 or larger (nonstandard-size paper: 8 inches / 203 mm or more in length) Important If the Top Cover is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Top Cover to return the Holder to the center. Note If the ALARM lamp on the printer flashes orange after you have closed the Top Cover, refer to "ALARM Lamp Flashes Orange" in "Troubleshooting" of the Quick Start Guide. 5" x 7" or smaller (nonstandard-size paper: less than 8 inches / 203 mm in length) d Load the paper into the cassette with the print side facing DOWN. Note Loading paper in the cassette provides additional paper handling flexibility. For additional information, refer to the User's Guide.