Canon LV-8225 LV-7290 Network Set-up and Operation User's Manual
Canon LV-8225 Manual
 |
View all Canon LV-8225 manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon LV-8225 manual content summary:
- Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 1
function. Read this manual thoroughly to operate the Network function. First, read the user's manual of the projector to understand the basic operation of the projector and the safety instructions. The safety instructions in the user's manuals should be followed strictly. for LV-7290/7295/7390/8225 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 2
Inc. One Canon Plaza, Lake Success, NY 11042-1198, U.S.A. Tel No. (516)328-5600 Canadian Radio Interference Regulations This class B digital apparatus complies with Canadian ICES-003. CAUTION IN USING THE PROJECTOR VIA NETWORKS ● When you find a problem with the projector, remove the power cable - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 3
manual to alert you to important safety information. Always observe the instructions instructions specified by the projector and peripheral equipment makers. D o not attempt to disassemble or service touch the projector with wet hands when the power cord plugs of the projector or peripheral - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 4
instructions...3 Table of contents...4 Chapter 1 Preparation 5 Features...6 Required operating environment for computers 7 Network specifications of the projector mail 28 SNMP setting...29 Chapter 4 Controlling the Projector 31 Power control and status check...32 Control...34 Input...34 System - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 5
Chapter 1 Preparation Describes features and operating environment of this projector. 1 ENGLISH - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 6
sends mes- sages to the registered e-mail PC1 PC2 addresses when a lamp abnor- mality or power failure occurs with the projector. This mes- sage describes how to solve the PC3 PC4 cause of the problems. You can take efficient action for quick recovery. PJ2 PJ1 PC5 Turn ON PJ2 PC6 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 7
7 Macintosh : 256MB or more (512MB is recommended) 100MB or more CD-ROM drive Support one of following resolutions; VGA (640 x 480), SVGA(800 x 600), XGA(1,024 x or 9.0 Safari 3.1 * Used to control and set up the projector. The layout of pages in the browser may slightly differ from each type - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 8
actual operation depending on your computer environment. Use of this manual This manual does not provide the detailed description of basic operation and functions for computer, web browser, projector and network. For instructions about each piece of equipment or application software, please refer - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 9
and operation" (pp.17-30). STEP 2 Network Configuration has completed. Follow each chapter to operate the projector. ■ Operate and manage the projector ➔ "4. Controlling the projector" (pp.31-43) ➔ "Power Control and status check" (p.32) ➔ "Control" (p.34) ➔ "PC adjustment" (p.38) ➔ "Setting up the - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 10
Chapter 1 Preparation 10 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 11
Chapter 2 Setup Procedures Describes how to configure the network. 2 ENGLISH 11 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 12
is connected to the network correctly. LAN Cable * Please use a shielded LAN cable. Network configuration Set the Wired LAN network through the projector menu. Detailed network settings will be made with browser. Refer to "3. Basic setting and operation" (p.17-30). First, complete the settings - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 13
DHCP Sets DHCP function On or Off. When you setup the network setting manually, select "Off". When it is set On, IP address, Subnet, Gateway to your network environment *1. IP address Sets IP address of the projector Subnet Sets Subnet mask according to your network environment. Gateway*2 Sets - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 14
"0000". It is recommended to set the Network PIN code if you use the projector via the networks. The Network PIN code can be set also through the networks. or OK button to show LAN setting environment of the currently selected projector. (The description below is an example and different from what - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 15
Network factory default Network factory default 1. Select "Network factory default" in the Network menu and press OK button. 2. A confirmation box appears and select "Yes" and then press OK button. 3. Another confirmation box appears and select "Yes" and then press OK button. 4. All the wired LAN - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 16
Chapter 2 Setup Procedures Wired LAN factory default settings Parameter LAN 1 SELECTED LAN LAN 2 LAN 3 DHCP OFF ON OFF IP ADDRESS 169.254.100.100 192.168.100.100 192.168.100.100 SUBNET MASK 255.255.0.0 255.255.255.0 255.255.255.0 GATEWAY ADDRESS 255.255.255.255 255.255.255.255 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 17
Chapter 3 Basic Setting and Operation Describes basic operations and settings for controlling the projector by using the web browser. It is required that computer and projector is connected to the network and the network address is properly configured. 3 ENGLISH 17 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 18
Basic Setting and Operation Login the setting page of the projector [1] Enter the IP address Launch the web browser entering User Name must be "user" and it can not be changed. [Note] When accessing the projector for the first time or the Network PIN code "0000" is set, the auto-login will be - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 19
Login the setting page of the projector [3] Display of main setting page The following main setting page will be menu tab. Main menu For selection of control and setting items of the projector. Setting page Displays the control and setting items according to the selected menu. ENGLISH 19 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 20
3 Basic Setting and Operation How to use the setting page To control and set up the projector, use the setting menus on the web browser. Describes the basic operation and procedures commonly used on this manual. Example of the setting page The setting menu appears when clicking the sub menu tab - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 21
Radio button setting Select an item by selecting a radio button. Check box setting Select items by ticking on check boxes. How to use the setting page ENGLISH 21 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 22
display language on the setting page. (Japanese, English) Model name........Indicates the model name of the projector SERIAL NO. ..........Indicates the serial number of the projector Network PIN code.......Sets the Network PIN code to login the setting page (+p.23) PJLink Switches PJLink - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 23
System Industries Association (JBMIA). Please visit the Website at http://pjlink.jbmia.or.jp/english/. PJLink Notice The projector is compliant with PJLink Standard Class 1 of JBMIA, and it supports all commands defined by PJLink Class 1 and is verified conformance with PJLink Standard Class - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 24
in chapter "Installation". If you want to change them or configure default gateway or DNS, perform them in this page. If you change them, the projector begins restarting and it takes about 10 seconds. Close (Quit) the web browser and access to the login page again in 10 seconds. Item Description - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 25
1 to 65535) Administrator address....Enter e-mail address of administrator. Add address Enter e-mail address of the user to send mail when the projector has an abnormality. SMTP Authentication setting Auth Sets authentication setting option. (Off, SMTP Auth, POP before SMTP) SMTP Auth Sets user - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 26
setting page correctly. ✐ You cannot use this E-mail function if the DNS server and SMTP server cannot be used in your network environment. ✐ The projector does not send message to the address set in "Administrator address" text box. If you want to send e-mails to the administrator address, enter - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 27
PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 28
lamp was turned off, because the projector power circuit failed. Unplug the AC power cord and plug it, and then turn on the projector once again to verify operation. If the problem still persists, unplug the AC power cord and ask servicing to a qualified service personnel with the error information - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 29
SNMP is called "Community". There are two access modes in a community, Refer (read only) and Set (readwrite). This projector allows to use Refer (read only) only. The SNMP message informs the projector status called "Trap" to an administrator. Click SNMP Setting on the main menu and set up each item - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 30
PJ lamp is off" signifies the lamp goes out without user operation. "When PJ is turned into Standby in proper user operation" signifies that the projector is turned on by using the web browser and then it is turned into standby with ON/STANDBY button on the top control or the - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 31
Chapter 4 Controlling the Projector Describes controlling and setting of the projector by using the web browser. 4 ENGLISH 31 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 32
starting up, On cooling down, Service in need) Status Displays the status of the projector's power. (Refer to next page.) Power control.........Controls the projector power by clicking the "ON" or "Standby" button. ✐ The projector cannot be turned on while the projector is on cooling down. ✐ The - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 33
temp. and sets into standby mode. Power failure Power failure has occurred inside the projector. Projector is turned off. Unplug the AC cord and ask servicing to a qualified service personnel. When a security (PIN code lock) has been set on the projector, you also cannot control it through the - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 34
differs depending on the contents of the page. Click on the page number to change pages and select desired setting items. ✐ Please see the user's manual of the projector to have the further information of each control item. Input This function is to select the input mode and source mode of the - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 35
function is to select the system of signal input to the projector. The available system mode are listed on the pull-down menu input signal. * The computer system modes (VGA, SVGA, XGA. SXGA, UXGA, WXGA...) which meet the input signal are listed. Available selection at the VIDEO/S-VIDEO/SCART input - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 36
Sound This function is to adjust the sound of the projector. The values in the text box represent the current control value or status. Item Description Volume Adjusts the sound volume through the network. When using the MIC functions, please set by using the On Screen Menu of the projector. 36 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 37
Control Image adjustment This function is to adjust the projected picture image and save the image mode. To store the adjusted value, click Store button, and to load the adjusted value, click Load button. Item Description Contrast Adjusts picture contrast (0~ 63) Brightness Adjusts picture - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 38
function is to adjust the signal from the computer connected to the projector to obtain the proper picture image on the screen. Item Description Current mode......Displays a current mode like VGA, SVGA, XGA. SXGA, UXGA, WXGA, etc. or Mode1 - Mode10 which are the customized mode created by using - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 39
Aspect setting This function is to adjust the aspect mode of the projector. The values in the text box represent the current aspect status Natural wide and Screen aspect are only available for LV-8225. Table of Aspect mode for LV-7290, LV-7295 and LV-7390 Aspect mode Normal Full 16:9 Zoom True - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 40
Chapter 4 Controlling the Projector Table of Aspect mode for LV-8225 Screen Aspect Screen mode Normal Full 16:9 Zoom True Natural wide Custom Default(16:10) OFF) Auto keystone.....Sets Auto Keystone mode. (Auto, Manual, OFF) Background.........Sets the screen background when no signal input - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 41
on Sets the power-on mode when the AC cord is connected to the outlet. (ON, OFF) Lamp mode.........Selects lamp control mode. (High, Normal, Eco) Key lock Sets the prohibition of controls either Projector or Remote control. (OFF, Projector, Remote control) Fan control Sets the fan control speed - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 42
the next page. Security Displays the security (PIN code lock) status (Yes, No) PJ time(h Displays the accumulated use time of the projector. Lamp Corres. Value(h).....Displays the use time (Corresponding value) of the lamp. Filter time(h Displays the accumulated use time of the filter. Network - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 43
Information Indication of the lamp status Icon display/background Status White/Blue Lamp on (Normal) White/Red Lamp on (Lamp is being used over a specified use time, replace lamp immediately) Gray/Blue Gray/Red Lamp off (Normal) Lamp off (Lamp is being used over a specified use time, replace - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 44
Chapter 4 Controlling the Projector 44 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 45
Chapter 5 Appendix Connection examples Use of telnet Web browser setting Q & A 5 ENGLISH 45 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 46
the hub. Hub To another network Computer Name: PC05 IP Address : 192.168.0.5 Subnet Mask : 255.255.255.0 Default Gateway : DNS : Projector Name: PJ01 IP Address : 192.168.0.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0 DNS : 0.0.0.0 Computer Name: PC10 IP Address : 192.168 - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 47
. Entrance hall Computer Name IP Address Subnet Mask Default Gateway DNS : PC205 : 192.168.200.5 : 255.255.255.0 : 192.168.200.1 : 192.168.201.1 Projector Name: PJ01 IP Address : 192.168.200.15 Subnet Mask : 255.255.255.0 Default Gateway : 192.168.200.1 DNS : 192.168.201.1 Network Group - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 48
*1 installed on your computer. Normally, the telnet application is available on your computer. * The telnet 10000 port is used to control the projector. Control (For example, in case of using the telnet application of Windows XP Professional.) 1. Select Run... submenu from Start menu on the - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 49
(Network PIN code*2) for the projector and then press "Enter" key on Power on C02 Power off C09 Volume up C0A Volume down C0B Audio Mute on C0C Audio Mute off C1C Menu display on C1D Menu display off *1 F urther instructions about the telnet application, please see the on-line guide - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 50
is set not to use this JavaScript function, it may not control the projector properly. In this case, the warning message "Make sure JavaScript is ON." on the top of the page. To enable the JavaScript, please see further instructions on the next page. Proxy setting In some cases, your web browser is - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 51
Examples: OS/Browsers Windows XP Professional Web browser setting Internet Explorer v.6.0 ActiveScript setting Select Internet Options from Tools menu on the web browser and then select Security tab and click Customize Level... button. On the security setting window, scroll down and find the - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 52
proxy server address and port correctly in the proxy settings window. For further instruction please consult your network administrator. - Not using proxy server Uncheck the item Use a proxy server. If you connect the projector to the computer directly with STP cross cable, this must be unchecked - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 53
to which the projector is connected. - Using proxy server When you use an external internet connection from the local area network, select the item Manual proxy configuration. Enter the proxy server address and port number correctly on HTTP Proxy item. For further instruction please consult your - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 54
address and port correctly in Web Proxy Server window. For further instruction please consult your network administrator. - Not using proxy server Uncheck HTTPS) of Select a proxy server to configure. If you connect the projector to the computer directly with STP cross cable, they must be unchecked - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 55
status (☞ p.12). - Check the connection of LAN cable if the LINK Lamp does not light green. - Check the network configuration of the projector if the ACT Lamp does not blink orange. 2. Wrong network configuration of the computer. Check the network configuration of the computer. 3. The proxy - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 56
Q W e use the DHCP/BOOTP server to assign the IP address. Is it possible to use the projector in this network environment? A P ossible. This projector supports the DHCP/BOOTP server. To use this projector in this network environment, set it up so that the DHCP/BOOTP server does not assign the IP - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 57
is turned on. If it is in the standby mode, the setting is not effective to the projector. To control the projector with a web browser, the projector must be in the powered-on condition. Q Why does it sometimes take a lot of time to complete the page display? A The display speed of the page - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 58
, they cannot establish communications each other. In this case, the router is placed in the networks to make the routing. Q Can I control the projector by using the telnet application? A Possible. Please refer to the item "Use of telnet" (☞ p.48 - 49). Q What is the MAC address assigned to - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 59
Q&A Q Can I update the firmware of the projector. A It is possible to update the firmware through the network. It is required to have a special tool for the updating. For further information please consult - Canon LV-8225 | LV-7290 Network Set-up and Operation User's Manual - Page 60
, Gangnam-gu, Seoul, 135-984, Korea OCEANIA CANON AUSTRALIA PTY. LTD. 1 Thomas Holt Drive, North Ryde, N.S.W. 2113, Australia CANON NEW ZEALAND LTD. Akoranga Business Park, Akoranga Drive, Northcote, Auckland, New Zealand LV-7290/7295/7390/8225 NETWORK USER'S MANUAL SO-KT8PE 1 © CANON INC. 2011
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
 |
 |
Wired Setting
Projector Set-up and Operation
User’s Manual
Network Set-up and Operation
This is the manual for the Network function.
Read this manual thoroughly to operate the Network function.
First, read the user's manual of the projector to understand the basic
operation of the projector and the safety instructions.
The safety instructions in the user's manuals should be followed strictly.
for LV-7290/7295/7390/8225