Canon LV-X1 Owners Manual - Page 38

Appendix, Lamp Replacement, Lamp Replace Counter - bulb

Get Canon LV-X1 PDF manuals and user guides View all Canon LV-X1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

APPENDIX LAMP REPLACEMENT When the life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow. When a projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required. CAUTION For continued safety, replace with a lamp assembly of the same type. Allow a projector to cool for at least 45 minutes before you open Lamp Cover. The inside of a projector can become very hot. CAUTION Do not drop a lamp assembly or touch a glass bulb! The glass can shatter and may cause injury. Follow these steps to replace the lamp assembly. 1 Turn off the projector and disconnect AC plug. Allow the projector to cool for at least 45 minutes. 2 Remove a screw with a screwdriver to remove Lamp Cover. 3 Remove 2 screws with a screwdriver and pull out Lamp Assembly by grasping Handle. 4 Replace Lamp Assembly with a new one and tighten 2 screws back. Make sure that Lamp Assembly is set properly. Replace Lamp Cover and tighten a screw. 5 Connect AC Power Cord to the projector and turn it on. 6 Reset Lamp Replace Counter (refer to the section "Lamp Replace Counter" below). NOTE : Do not reset Lamp Replace Counter when Projection Lamp is not replaced. LAMP COVER HANDLE LAMP ASSEMBLY ORDER REPLACEMENT LAMP Replacement Lamp can be ordered through your dealer. When ordering Projection Lamp, give the following information to the dealer. q Model No. of your projector : LV-X1 q Replacement Lamp Type No. : LV-LP12 (Service Parts No. 610 293 8210) LAMP REPLACE COUNTER Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced. When Lamp Replace Counter is reset, LAMP REPLACE Indicator stops lighting. 1 Turn projector on, press MENU button and ON-SCREEN MENU will appear. Press POINT LEFT/RIGHT button(s) to move a red frame pointer to SETTING Menu icon (refer to page 35, 36). 2 Press POINT DOWN button to move a red frame pointer to "Lamp counter reset" and then press SET button. The message "Lamp replace counter reset?" is displayed. Move the pointer to [Yes] and then press SET button. 3 Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter. Do not reset Lamp Replace Counter except after Projection Lamp is replaced. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
38
APPENDIX
LAMP REPLACEMENT
When the life of Projection Lamp of this projector draws to an end, LAMP REPLACEMENT indicator lights yellow.
When a
projected image becomes dark or the color of an image becomes unnatural, replacement of Projection Lamp is required.
Turn off the projector and disconnect AC plug.
Allow the
projector to cool for at least 45 minutes.
Remove 2 screws with a screwdriver and pull out Lamp
Assembly by grasping Handle.
1
3
Replace Lamp Assembly with a new one and tighten 2 screws
back.
Make sure that Lamp Assembly is set properly.
Replace
Lamp Cover and tighten a screw.
4
Remove a screw with a screwdriver to remove Lamp Cover.
2
Connect AC Power Cord to the projector and turn it on.
6
Follow these steps to replace the lamp assembly.
Reset Lamp Replace Counter (refer to the section “Lamp
Replace Counter” below).
5
LAMP
ASSEMBLY
HANDLE
LAMP COVER
NOTE :
Do not reset Lamp Replace Counter when Projection
Lamp is not replaced.
ORDER REPLA
CEMENT LAMP
Replacement Lamp can be ordered through your dealer.
When ordering Projection Lamp, give the following
information to the dealer.
●
Model No. of your projector
: LV-X1
●
Replacement Lamp Type No. :
LV-LP12
(Service Parts No. 610 293 8210)
LAMP REPLACE COUNTER
Be sure to reset Lamp Replace Counter when Lamp Assembly is replaced.
When Lamp Replace Counter is reset, LAMP
REPLACE Indicator stops lighting.
Turn projector on, press MENU button and ON-SCREEN MENU will appear.
Press POINT LEFT/RIGHT button(s) to
move a red frame pointer to SETTING Menu icon (refer to page 35, 36).
1
Press POINT DOWN button to move a red frame pointer to “Lamp counter reset” and then press SET button.
The
message "Lamp replace counter reset?" is displayed.
Move the pointer to [Yes] and then press SET button.
2
Do not reset Lamp Replace Counter except after Projection Lamp is replaced.
Another confirmation dialog box appears and select [Yes] to reset Lamp Replace Counter.
3
CAUTION
Do not drop a lamp assembly or touch a glass
bulb! The glass can shatter and may cause
injury.
CAUTION
For continued safety, replace with a lamp
assembly of the same type.
Allow a projector to cool for at least 45
minutes before you open Lamp Cover.
The
inside of a projector can become very hot.