Canon PIXMA MP510 Easy Setup Instructions - Page 1

Start Here Easy Setup Instructions Unpack the Machine • Please confirm the included items against the illustration printed on the lid of the packing box. • A USB cable is necessary to connect the machine with your computer. QT5-0453-V02 1 Prepare the Machine a Place the machine on a flat and horizontal surface, and do not place any objects in front of the machine. Open the Front Feeder, and extend the Paper Output Support and the Paper Support. Caution Before turning on the machine, remove all of the shipping tapes. Important Do not connect the USB cable until after the software is installed. Important If an unintended language is displayed on the LCD, proceed setup to the end of step 3 "Install the Ink Tanks", and then refer to "An Unintended Language Is Displayed on the LCD" in "Troubleshooting" of the User's Guide on-screen manual to change the LCD language. If the message appears, go to e. e Lift the Scanning Unit (Printer Cover) open, and set the Scanning Unit Support to hold the cover. The Print Head Holder moves to the center. Scanning Unit (Printer Cover) b Plug the power cord in the back of the machine and connect the other end to the wall outlet. f Write down the serial number located inside the machine. You will need this to register your product. 2 Install the Print Head a Remove the Print Head from its package. Caution There may be some transparent or light blue ink on the inside of the bag the print head comes in, or the inside of the protective cap - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. b Remove the orange protective cap from the Print Head and discard it. Electrical Contacts Protective Cap Print Head Nozzles Note Do not touch the print head nozzles and the electrical contacts. c Firmly raise the Print Head Lock Lever until it stops. 3 Install the Ink Tanks a Peel back the orange tab completely and remove the plastic wrapper from the ink tank. If the orange-colored protective film is not removed completely, problems with printing may occur. b Twist off and discard the orange protective cap located on the bottom of the ink tank. Do not press! Protective Cap Ink Port Electrical Contacts Important • Do not touch the electrical contacts. • Do not touch the ink port. c Insert the ink tank into the right-hand slot and press the mark on the ink tank until it clicks into place. Important • Plug the power cord all the way in, since it may be difficult to plug. • Make sure that the Document Cover is closed. c Open the Operation Panel, then press the ON/ OFF button to turn on the machine. d Use the { or } button on the Operation Panel to select the language for the LCD, then press the OK button. (1) Press the { or } button to select the language. (2) Press the OK button. Serial Number Location d Insert the Print Head. Do not touch! d Make sure the ink lamp lights red. Refer to the color guide on the Print Head Lock Lever. e Lower the Print Head Lock Lever carefully. e Lift the Scanning Unit (Printer Cover) slightly to set the Scanning Unit Support back to its original position, and then gently close the Scanning Unit (Printer Cover). Important If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center. Important The machine starts operating. Wait about 2 minutes until the machine stops making noise. Hardware setup is complete. Photo All-in-One Loading Paper This machine offers two paper sources to load printing paper; the Auto Sheet Feeder, found at the top of the machine, and the Front Feeder, found at the front of the machine. Note • At purchase, the machine is set to feed from the Auto Sheet Feeder. • You can load A4, Letter, or B5-sized plain paper in the Front Feeder. When using any other type of paper, load it in the Auto Sheet Feeder. Auto Sheet Feeder Front Feeder Loading Paper in the Auto Sheet Feeder a Load the paper in the Auto Sheet Feeder with the print side facing UP. b Align the paper stack against the Cover Guide on the right side of the Paper Support. c Pinch the Paper Guide and slide it against the left side of the paper stack. Paper Guide Print side facing UP. Cover Guide Loading Paper in the Front Feeder a Load the paper in the Front Feeder with the print side facing DOWN and the leading edge to the far side. b Align the paper stack against the right edge of the Front Feeder. c Align the near and the left edges of the paper with the Paper Size Mark. d Pinch the Paper Guide and slide it against the left side of the loaded paper stack. Paper Guide Print side facing DOWN. Paper Size Mark Note For details, refer to the Quick Start Guide.