Canon PIXMA MP530 Easy Setup Instructions - Page 1
Canon PIXMA MP530 Manual
View all Canon PIXMA MP530 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 1 highlights
Start Here Easy Setup Instructions Unpack the machine Please confirm bundled thing by the illustration printed on the flapped lid of the packing box. QT5-0214-V01 1 Prepare the machine 1 Remove the shipping tape from the machine. IMPORTANT Make sure to remove the protective film from the Feeder Cover. 5 Press the Open button to open the Paper Output Tray. Open up and set the Paper Output Tray extension by pressing down the hollow on its front side. Open Button Paper Output Tray 2 Install the Print Head 1 Remove the Print Head from its package. 2 Connect the telephone line and any necessary external device. Connect the telephone line cord to the wall jack. You can connect an external device (telephone or answering machine) if necessary. Connect external devices as follows: External device jack Telephone line jack Telephone or answering machine Telephone line Machine Telephone or answering machine Built-in computer modem and telephone Telephone line Machine LINE TEL Computer Telephone IMPORTANT Be sure to use the bundled telephone line cable. 3 Plug the power cord into the back of the machine and connect the other end to a power outlet. Press [ON/OFF]. 4 Use [ ] or [ ] on the Operation Panel to select the language for the LCD, then press [OK]. 6 Open the Scanning Unit (Printer Cover) until it locks into place. The Print Head Holder moves to the center. Scanning Unit (Printer Cover) IMPORTANT Be careful not to touch the buttons on the Operation Panel. 7 Open the Inner Cover. Write down the serial number located inside the machine. You will need this to register your products. Inner Cover Serial Number Location CAUTION There might be some transparent or light blue ink on the inside of the bag the print head comes in - this has no effect on print quality. Be careful not to get ink on yourself when handling these items. 2 Remove the orange protective cap from the Print Head and discard it. Do not touch the Print Head nozzles and the electrical contacts. Print Head Nozzles Protective Cap Electrical Contacts 3 Firmly raise the Print Head Lock Lever until it stops. 4 Insert the Print Head. Do not touch! 5 Lower the Print Head Lock Lever carefully and press it down. 3 Install the ink tanks 1 Peel back the orange tab completely and remove the plastic wrapper from the ink tank. If the orange-colored protective film is not removed completely, problems with printing may occur. 2 Twist off and discard the orange protective cap located on the bottom of the ink tank. Do not press! Protective Cap Electrical Contacts IMPORTANT • Do not touch the electrical contacts. • Do not touch the ink port. ink port 3 Insert the ink tank into the right-hand slot. 4 Press the mark on the ink tank until it clicks into place and then its lamp lights red. Refer to the color guide on the Print Head Lock Lever. Click 4 Align the Print Head 1 Open the Paper Support, then pull out the extension. Pinch the Paper Guide and slide it to the left. Paper Support Extension Paper Guide 2 Load a few sheets of letter- or A4-size paper into the Auto Sheet Feeder, align the paper with the right side of the Cover Guide, then slide the Paper Guide toward the left edge of the paper. Paper Guide Print Side Cover Guide 3 Ensure that the message requesting head alignment is displayed on the LCD, select using [ ] or [ ] and press [OK]. Hardware setup and Print Head alignment is complete. If you are connecting the machine to a computer for use, see the back side of this sheet for instructions on installing the software. For fax users To send a fax, you need to set the telephone line type setting properly on the machine. You have a dedicated telephone line for fax use only: → FAX ONLY MODE You receive mainly voice calls and sometimes faxes, and you want to receive faxes manually: → MANUAL MODE You want to receive voice messages on your answering machine, and receive faxes automatically: → ANS.MACHINE MODE You want to switch faxes and voice calls automatically: → FAX/TEL AUTO SW You have subscribed to a Distinctive Ring Pattern Detection (DRPD) service with your telephone company: → DRPD For details about the receive mode setting, refer to "Receiving Faxes" in the User's Guide. If you are unsure of your telephone line type, contact your telephone company. Cassette Loading You can load paper in both the Auto Sheet Feeder and Cassette. 1 Pull out the Cassette from the bottom of the machine. 5 Close the Inner Cover and the Scanning Unit (Printer Cover). Click The pattern is printed. And Print Head is aligned automatically. Cassette 2 Load the stack of paper into the Cassette with the print side face down. Pinch the Paper Guide and align it to the stack. Paper Guide If the message appears, go to 5 . IMPORTANT If the Scanning Unit (Printer Cover) is left open for more than 10 minutes, the Print Head Holder moves to the right. Close and reopen the Scanning Unit (Printer Cover) to return the Holder to the center. IMPORTANT For safety, always firmly grip the areas illustrated when closing the Scanning Unit (Printer Cover). • The pattern is printed in black and blue. • Print Head alignment will take several minutes to complete. Do not start another operation here. • When automatic Print Head alignment cannot be executed correctly, the message is displayed on the LCD. Refer to "An Error Message is Displayed on the LCD" in the User's Guide.