Canon PIXMA iP4500 iP4500 series Easy Setup Instructions - Page 2

Windows, Software Installation and Print Head Alignment, Macintosh - user manual

Get Canon PIXMA iP4500 PDF manuals and user guides View all Canon PIXMA iP4500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 2 highlights

Windows® Software Installation and Print Head Alignment Macintosh® Software Installation and Print Head Alignment Windows Important If you cannot go to the next procedure after 2 minutes, refer to "Troubleshooting" instructions in the Quick Start Guide. Macintosh j When the Print Head Alignment screen appears, make sure that two sheets of supplied paper (MP-101) are loaded in the Rear Tray (top paper feeder). Click Execute, confirm the displayed message, and click OK. Note • The screens below refer to Windows Vista™ operating system Ultimate Edition (hereafter referred to as "Windows Vista") installation. Screens may vary depending on the operating system you are using. • Log into a user account with the administrator privilege. • Before installing the software, disable all anti-virus programs and automatically loading programs. • A message asking for your confirmation to restart your computer may appear during the installation process. If this message is displayed, follow the on-screen instructions and click OK. The installation resumes from where it left off when your computer has been restarted. • If the computer is restarted during installation, do not remove the Setup CD-ROM during restarting. a Be sure to TURN THE PRINTER OFF before continuing. (1) Press the POWER button. (2) Make sure that the POWER lamp stops flashing. b Turn the computer on and start Windows. Important If the Found New Hardware or Found New Hardware Wizard screen appears automatically, remove the USB cable connected to your computer. Click Cancel to quit the screen. In Windows Vista, the screen may close automatically when the USB cable is unplugged. Then turn off the printer and proceed from step c to install the printer driver. c Insert the Setup CD-ROM. The setup program should run automatically. In Windows Vista, go to Step d. In Windows XP and Windows 2000, go to Step f. d If the AutoPlay screen appears, click Run Msetup4.exe. e If the User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue. f When the main menu appears, click Easy Install. The printer driver, On-screen Manuals, and application software are installed automatically. ← To Computer USB j When the Print Head Alignment screen appears, make sure that two sheets of supplied paper (MP-101) are loaded in the Rear Tray (top paper feeder). Click Execute, confirm the displayed message and click Print Head Alignment. Note • Since Mac® OS 9, Mac OS X Classic environments, or Mac OS X v.10.2.7 or earlier are not supported, do not connect the printer to these. • The screens below refer to Mac OS X v.10.4.x installation. Screens may vary depending on the operating system you are using. • Log on as an Administrator. • Before installing the software, disable all anti-virus programs and automatically loading programs. a Connect one end of the USB cable to the computer, the other to the printer. Note Make sure the printer is turned on. Note • Print Head Alignment will take about 13 minutes to complete. Do not start another operation here. • Do not open the Top Cover and Inner Cover while printing. The pattern is printed, and the Print Head is aligned automatically. Note • The pattern is printed in black and blue. • When Automatic Print Head Alignment cannot be executed properly, the ALARM lamp on the printer will flash orange eleven times. Refer to "ALARM Lamp Flashes Orange" in "Troubleshooting" of the Quick Start Guide. k After print head alignment is completed, click Next. l When the Installation Results screen appears, click Next. m When the User Registration screen appears, click Next. Note To register later, click Cancel and go to Step n. After software installation is complete, double-click on the desktop . Follow on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the printer. USB b Turn on your Mac and insert the Setup CD-ROM. Note If the CD-ROM folder does not open automatically, double-click the CD-ROM icon on the desktop. c Double-click the Setup icon. d When the Authenticate screen appears, enter your administrator name and password. Click OK. If you do not know your administrator name or password, click , then follow the on-screen instructions. e When the main menu appears, click Easy Install. The printer driver, On-screen Manuals, and application software are installed automatically. Note • Print Head Alignment will take about 13 minutes to complete. Do not start another operation here. • Do not open the Top Cover and Inner Cover while printing. The pattern is printed, and the Print Head is aligned automatically. Note • The pattern is printed in black and blue. • When Automatic Print Head Alignment cannot be executed properly, the ALARM lamp on the printer will flash orange eleven times. Refer to "ALARM Lamp Flashes Orange" in "Troubleshooting" of the Quick Start Guide. k When the Setup Complete screen appears, click Next. l When the User Registration screen appears, click Next. Note To register later, click Cancel and go to Step m. After software installation is complete, double-click on the desktop. Follow on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the printer. Serial Number m When the Installation completed successfully screen appears, click Exit. If Restart is displayed, click Restart. Remove the CD-ROM after clicking Restart and restarting the computer. Note If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed the installation. Note Keep the CD-ROM in a safe place in case you need to reinstall the software. Note If you want to select particular items to install, click Custom Install and follow the onscreen instructions to proceed the installation. g When the list of applications to install appears, confirm the contents, click Install. Note Move the cursor over items to display explanations of each application. h Read the License Agreement carefully and click Yes. The software installation screen may appear during the installation process. Follow the on-screen instructions to install the software. i When the Printer Connection screen appears, connect one end of the USB cable to the computer, the other to the printer, then TURN THE PRINTER ON. The printer driver will begin identifying the printer port being used. Serial Number n When the PIXMA Extended Survey Program screen appears, confirm the message. We would appreciate it if you would take part in this program regarding the use of Canon printers. If you can agree, click Agree. o When the Installation completed successfully screen appears, click Exit. If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart. Remove the CD-ROM after clicking Restart and restarting the computer. Note Keep the CD-ROM in a safe place in case you need to reinstall the software. Software installation and print head alignment are now complete. f When the list of applications to install appears, confirm the contents, then click Install. Note Move the cursor over items to display explanations of each application. g Read the License Agreement carefully and click Yes. The software installation screen may appear during the installation process. Follow the on-screen instructions to install the software. h When the Start Setup screen appears, click Execute. i When the Printer Connection screen appears, confirm the displayed message and click Restart. The system is restarted automatically. Note Do not remove the Setup CD-ROM while your computer is being restarted. Software installation and print head alignment are now complete. Part no. QT5-1273-V02 © 2007 Canon Inc. "Microsoft" is a registered trademark of Microsoft Corporation. "Windows" is a trademark of Microsoft Corporation, registered in the U.S. and other countries. "Windows Vista" is a trademark of Microsoft Corporation. "Macintosh" and "Mac" are trademarks of Apple Inc., registered in the U.S. and other countries. XXXXXXXX PRINTED IN THAILAND

  • 1
  • 2
Windows
Macintosh
Windows
®
Software Installation and Print Head Alignment
Note
The screens below refer to Windows Vista™ operating system Ultimate Edition
(hereafter referred to as “Windows Vista”) installation.
Screens may vary depending on the operating system you are using.
Log into a user account with the administrator privilege.
Before installing the software, disable all anti-virus programs and automatically
loading programs.
A message asking for your confirmation to restart your computer may appear
during the installation process. If this message is displayed, follow the on-screen
instructions and click
OK
.
The installation resumes from where it left off when your computer has been
restarted.
If the computer is restarted during installation, do not remove the
Setup CD-ROM
during restarting.
a
Be sure to
TURN THE PRINTER OFF
before continuing.
(1) Press the
POWER
button.
(2) Make sure that the
POWER
lamp stops flashing.
b
Turn the computer on and start Windows.
Important
If the Found New Hardware or Found New Hardware Wizard screen appears
automatically, remove the USB cable connected to your computer. Click
Cancel
to quit the screen. In Windows Vista, the screen may close automatically when
the USB cable is unplugged. Then turn off the printer and proceed from step
c
to install the printer driver.
c
Insert the
Setup CD-ROM
. The setup program should run
automatically.
In Windows Vista, go to Step
d
. In Windows XP and Windows 2000, go to
Step
f
.
d
If the
AutoPlay
screen appears, click
Run Msetup4.exe
.
e
If the
User Account Control
screen appears, click
Continue
.
If the same screen reappears in subsequent steps, click
Continue
.
f
When the main menu appears, click
Easy Install
.
The printer driver, On-screen Manuals, and application software are installed
automatically.
Note
If you want to select particular items to install, click
Custom Install
and follow the on-
screen instructions to proceed the installation.
g
When the list of applications to install appears, confirm the
contents, click
Install
.
Note
Move the cursor over items to display explanations of each application.
h
Read the License Agreement carefully and click
Yes
. The
software installation screen may appear during the installation
process. Follow the on-screen instructions to install the
software.
i
When the
Printer Connection
screen appears, connect one
end of the USB cable to the computer, the other to the printer,
then
TURN THE PRINTER ON
. The printer driver will begin
identifying the printer port being used.
•
•
•
•
•
Important
If you cannot go to the next procedure after 2 minutes, refer to “Troubleshoot
-
ing” instructions in the
Quick Start Guide
.
USB
←
To Computer
j
When the
Print Head Alignment
screen appears, make sure
that two sheets of supplied paper (MP-101) are loaded in
the Rear Tray (top paper feeder). Click
Execute
, confirm the
displayed message and click
Print Head Alignment
.
Note
Print Head Alignment will take about 13 minutes to complete. Do not start another
operation here.
Do not open the Top Cover and Inner Cover while printing.
The pattern is printed, and the Print Head is aligned automatically.
Note
The pattern is printed in black and blue.
When Automatic Print Head Alignment cannot be executed properly, the
ALARM
lamp on the printer will flash orange eleven times. Refer to “ALARM Lamp Flashes
Orange” in “Troubleshooting” of the
Quick Start Guide
.
k
After print head alignment is completed, click
Next
.
l
When the
Installation Results
screen appears, click
Next
.
m
When the
User Registration
screen appears, click
Next
.
Note
To register later, click
Cancel
and go to Step
n
. After software installation is complete,
double-click
on the desktop .
Follow on-screen instructions to register your product. You will need your
product serial number, which is located on the inside of the printer.
Serial Number
n
When the
PIXMA Extended Survey Program
screen
appears, confirm the message. We would appreciate it if you
would take part in this program regarding the use of Canon
printers. If you can agree, click
Agree
.
o
When the
Installation completed successfully
screen
appears, click
Exit
.
If
Restart
is displayed, make sure that the
Restart the system now
(recommended)
check box is selected, then click
Restart
.
Remove the CD-ROM after clicking
Restart
and restarting the computer.
Note
Keep the CD-ROM in a safe place in case you need to reinstall the software.
Software installation and print head alignment
are now complete.
•
•
•
•
Macintosh
®
Software Installation and Print Head Alignment
Note
Since Mac
®
OS 9, Mac OS X Classic environments, or Mac OS X v.10.2.7 or earlier
are not supported, do not connect the printer to these.
The screens below refer to Mac OS X v.10.4.x installation. Screens may vary
depending on the operating system you are using.
Log on as an Administrator.
Before installing the software, disable all anti-virus programs and automatically
loading programs.
a
Connect one end of the USB cable to the computer, the other
to the printer.
Note
Make sure the printer is turned on.
USB
b
Turn on your Mac and insert the
Setup CD-ROM
.
Note
If the
CD-ROM
folder does not open automatically, double-click the
CD-ROM
icon
on the desktop.
c
Double-click the
Setup
icon.
d
When the
Authenticate
screen appears, enter your
administrator name and password. Click
OK
.
If you do not know your administrator name or password, click
, then follow the on-screen instructions.
e
When the main menu appears, click
Easy Install
.
The printer driver, On-screen Manuals, and application software are installed
automatically.
Note
If you want to select particular items to install, click
Custom Install
and follow the on-
screen instructions to proceed the installation.
f
When the list of applications to install appears, confirm the
contents, then click
Install
.
Note
Move the cursor over items to display explanations of each application.
g
Read the License Agreement carefully and click
Yes
. The
software installation screen may appear during the installation
process. Follow the on-screen instructions to install the
software.
h
When the
Start Setup
screen appears, click
Execute
.
i
When the
Printer Connection
screen appears, confirm the
displayed message and click
Restart
.
The system is restarted automatically.
Note
Do not remove the
Setup CD-ROM
while your computer is being restarted.
•
•
•
•
j
When the
Print Head Alignment
screen appears, make sure
that two sheets of supplied paper (MP-101) are loaded in
the Rear Tray (top paper feeder). Click
Execute
, confirm the
displayed message, and click
OK
.
Note
Print Head Alignment will take about 13 minutes to complete. Do not start another
operation here.
Do not open the Top Cover and Inner Cover while printing.
The pattern is printed, and the Print Head is aligned automatically.
Note
The pattern is printed in black and blue.
When Automatic Print Head Alignment cannot be executed properly, the
ALARM
lamp on the printer will flash orange eleven times. Refer to “ALARM Lamp Flashes
Orange” in “Troubleshooting” of the
Quick Start Guide
.
k
When the
Setup Complete
screen appears, click
Next
.
l
When the
User Registration
screen appears, click
Next
.
Note
To register later, click
Cancel
and go to Step
m
. After software installation is complete,
double-click
on the desktop.
Follow on-screen instructions to register your product. You will need your
product serial number, which is located on the inside of the printer.
Serial Number
m
When the
Installation completed successfully
screen
appears, click
Exit
.
If
Restart
is displayed, click
Restart
.
Remove the CD-ROM after clicking
Restart
and restarting the computer.
Note
Keep the CD-ROM in a safe place in case you need to reinstall the software.
Software installation and print head alignment
are now complete.
•
•
•
•
Part no.
QT5-1273-V02
© 2007 Canon Inc. “Microsoft” is a registered trademark of Microsoft Corporation. “Windows” is a trademark of Microsoft Corporation, registered in the U.S. and other countries. “Windows Vista” is a trademark of Microsoft Corporation. “Macintosh” and “Mac” are trademarks of Apple Inc., registered in the U.S. and other countries.
XXXXXXXX
PRINTED IN THAILAND