Canon PowerShot G1 Software Starter Guide DC SD Ver.2.0 - Page 11

Installing the USB Driver - troubleshooting

Get Canon PowerShot G1 PDF manuals and user guides View all Canon PowerShot G1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Windows 9 Installing the USB Driver (Preinstalled Windows 98/2000 Systems Only) Notes Regarding Installation • The USB driver only needs to be installed the first time the camera is connected via the USB interface. Installation is not required from the second time onward. • Do not cancel the installation partway through. Allow the procedure to finish completely before exiting. The camera may not operate correctly if the installation is incomplete. • Read the "Troubleshooting the USB Driver Installation" section on page 55 if the installation cancels itself during the procedure, if the installation does not proceed as described in these procedures, or if you think that the drivers are not properly installed. • Read the "Uninstalling the USB Driver" section on page 55 or 58 for instructions for that procedure. Installing the USB Driver into Windows 98 Windows 98 CD-ROM • Your computer may prompt you to insert the CD-ROM containing your Windows system software during the installation. Have the Windows disk handy in case it is required. 1. Once you have attached the USB cable to the camera and computer, set the camera to the mode for communicating with a computer. Refer to Where to Find Instructions for Attaching Your Camera to a Computer (§ p. iii) for connection instructions. The "Add New Hardware Wizard" dialog will appear after a moment. 2. Read the dialog and click the [Next] button. Your camera model name will appear here. The dialog will change to the search selection dialog.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
9
Windows
Installing the USB Driver
(Preinstalled Windows 98/2000 Systems Only)
Notes Regarding Installation
•
The USB driver only needs to be installed the first time the camera is connected via the
USB interface. Installation is not required from the second time onward.
•
Do not cancel the installation partway through. Allow the procedure to finish completely
before exiting. The camera may not operate correctly if the installation is incomplete.
•
Read the “Troubleshooting the USB Driver Installation” section on page 55 if the
installation cancels itself during the procedure, if the installation does not proceed as
described in these procedures, or if you think that the drivers are not properly installed.
•
Read the “Uninstalling the USB Driver” section on page 55 or 58 for instructions for
that procedure.
Installing the USB Driver into Windows 98
Windows 98 CD-ROM
•
Your computer may prompt you to insert the CD-ROM containing your Windows
system software during the installation. Have the Windows disk handy in case it is
required.
1.
Once you have attached the USB cable to the camera and computer, set
the camera to the mode for communicating with a computer.
Refer to
Where to Find Instructions for Attaching Your Camera to a
Computer
(
p. iii) for connection instructions.
The “Add New Hardware Wizard” dialog will appear after a moment.
2.
Read the dialog and click the [Next] button.
The dialog will change to the search selection dialog.
Your camera model name
will appear here.