Canon VB-M720F Network Camera VB-H730F/VB-M720F Installation Guide - Page 2

1 Mounting bracket Mounting screw holes Example installations Using a ceiling mounting bracket Using a wall mounting bracket 2 Power connector LAN cable Using an Memory Card Open the memory card cover as shown in the diagram to insert or remove the memory card. Firmly shut the memory card cover after inserting or removing the memory card. Memory card slot Memory card cover Inserting the card Push the memory card as far as possible into the memory card slot. Removing the card Push the memory card in all the way until the card slightly pops out. Pinch the card and remove. Important • Insert the memory card before installing the camera. • Make sure the memory card is not write-protected. • When using an memory card with the camera for the first time, it is recommended to format the card after inserting it into the camera (see "Operation Guide" > "Setting Page" > "Memory Card"). Installing the Camera Before installing the camera, set the IP address and other network information on the camera using the "Camera Management Tool" on the Setup CD-ROM. For details on how to operate the "Camera Management Tool", see "Camera Management Tool User Manual". 1 Mount the camera to the mounting bracket Use the mounting screw holes on the camera to securely fix the camera to the mounting bracket. Important • You must consult your retailer or provide the mounting bracket yourself. • A tripod mounting screw (1/4-20 UNC) will fit the fixing screw hole. • Be sure to use a mounting bracket with a mounting screw shorter than 5.5 mm (0.22 in.). Using a mounting bracket with a mounting screw 5.5 mm (0.22 in.) or longer may damage the camera. 2 Connect the cables to the camera Connect the LAN cable. If AC Adapter (sold separately) or an external power supply is used, connect the power connector to the camera. Connect cables to the external device I/O terminals and audio input/output terminals as necessary. 3 Set the camera angle When installation is complete, use the Camera Angle Setting Tool to check the image on the camera and manually adjust the camera angle. Zoom and focus can be adjusted with the Camera Angle Setting Tool (see "Operation Guide" > "Camera Angle Setting Tool"). Part Names MAC address The camera's unique address. Write the address on the front of this Installation Guide before installing the camera. Serial number The camera's serial number. Write the number on the front of this Installation Guide before installing the camera. Mounting screw holes Lens Protection plate Front cover Power connection terminal 100Base-TX LAN connector Audio output terminal (LINE OUT) External Device I/O Terminals LED The blue LED light comes on. • On: when powered on, during reboot, during normal use • Off: when [Turn Off] is selected (see "Operation Guide" > "Setting Page" > "Installation Conditions") * When [Turn Off] is selected, the LED light will come on for several seconds when the camera is powered on and during reboot. Reset Switch Turn on the power while pushing this switch using a sharp object. Continue to push the switch for 5 seconds or more to restore all factory settings except for the date and time. Memory card cover Audio input terminal (dual LINE IN and MIC IN) Using Camera Housing When using the camera mounted in commercial camera housing, remove the camera's protection plate to reduce the effects of excess reflections within the housing. • Remove the lock screw on the front cover and remove the front cover and protection plate. Then return only the front cover to its original position and fix in place with the lock screw. Lock screw Protection plate Front cover • When reattaching the protection plate, face the side with the cutout toward the lens. Cutout Connecting the Camera Power Connection Power can be supplied to the camera in the three ways described below. Please be sure to read the user manual for the dedicated power supply before use. Note • The camera does not have a power switch. Connecting and disconnecting the LAN cable (PoE power supply), AC adapter, or external power supply plug turns the power ON and OFF, respectively. • When the camera needs to be rebooted, perform the reboot operation from the camera setting page (see "Operation Guide" > "Setting Page" > "Maintenance").  PoE (Power over Ethernet) The camera supports PoE functions. Power can be supplied to the camera by using a LAN cable to connect it to a PoE HUB that conforms to the IEEE 802.3af standard. Important • Check with your dealer for more information about PoE HUB and Midspan technology. Midspan (a LAN cable power supply device) is a device that, like a PoE HUB, supplies power to the camera via a LAN cable. • Some PoE HUBs allow current limits for each port, but applying limits may interfere with performance. If using this type of PoE HUB, do not limit the operating current. • Some PoE HUBs have total consumption current limits for ports, which can interfere with performance when multiple ports are in use. For more information, check the instruction guide for your PoE HUB. • The camera can also be connected to an AC adapter (sold separately) while receiving power from a PoE HUB. In such cases, the PoE power supply is given priority, and the camera does not use the power supply from the AC adapter (sold separately). When the PoE power supply is disconnected, power is supplied automatically from the AC adapter (sold separately).  External Power Supply 12 V DC or 24 V AC input can be used. Connect the included power connector as shown below. Screwdriver Tightening torque: 0.25 N·m (max.) Strip Approx. 5 - 7 mm (0.20 - 0.28 in.) Power connector (included) 12 V DC can be connected in a non-polar configuration. Important • The power supply should be within the following voltage range. • 24 V AC: V oltage fluctuation within ±10% of 24 V AC (50 Hz or 60 Hz ±0.5 Hz or less) Current supply capacity of at least 1.0 A per camera • 12 V DC: Voltage fluctuation within ±10% of 12 V DC Current supply capacity of at least 1.5 A per camera • When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 - 1.0 Ω/20 W in series to the power line. • For an external power supply, use a double-insulated device. Recommended Power Cables [Reference] Cable (AWG) 24 Conductor diameter mm 0.52 (in.) ( 0.020) 12 V DC maximum cable length m (ft.) 5 (16.4) 24 V AC maximum cable length m (ft.) 11 (36.1) 22 0.65 ( 0.026) 9 (29.5) 18 (59.1) Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring. 20 0.82 ( 0.032) 14 (45.9) 29 (95.1)  AC Adapter Use the dedicated AC Adapter (sold separately). 18 1.03 ( 0.041) 23 (75.5) 46 (150.9) 16 1.30 ( 0.051) 32 (105.0) 64 (210.0) External Device I/O Terminals External device I/O terminals consist of two input and output systems each. Viewer can be used to check external device input status and control output to an external device (see "Operation Guide" > "Selecting the External Device Output" and "Displaying Event Status").  External Device Input Terminals (IN1, IN2) External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative terminals connected to the camera interior GND. Connecting cables to the positive and negative terminals and opening or closing the circuit notifies the Viewer. Important • When connecting sensors and switches, connect terminals that are electrically isolated from the respective power and GND. • Do not push the external device I/O terminal button with too much force. Doing so may cause the button to remain pushed-in.  External Device Output Terminals (OUT1, OUT2) External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets have no polarity. Controls from the viewer can be used to open and close the circuit between the terminals. Using optical couplers, the output terminals are isolated from the camera's internal circuit. The load connected to the output terminals should be within the following rating range. Rating between output terminals: Maximum voltage 50 V DC Continuous load current at or below 100 mA On resistance: Max. 30 Ω Internal Connection Diagram 10 kΩ 10 kΩ +3.3 V 1 kΩ Note External device 0.1 µF Input terminal IN1, IN2 External device Internal controller Adaptive wiring for external device cables Solid conductor AWG: No. 28 - 22 Conductor size: 0.32 - 0.65 mm ( 0.013 - 0.026 in.) Cable strip should be approx. 8 - 9 mm (0.31 - 0.35 in.) Output terminal OUT1, OUT2 Audio Input/Output Terminals Each audio input/output terminal has one input system and one output system. Connecting the camera to an audio input/output device such as a microphone or a speaker with an amplifier allows you to send/receive audio through the viewer.  Audio Input Dual LINE IN/MIC IN (monaural input) Although the camera has a single audio input system, it supports two types of microphone input: LINE IN and MIC IN. Before using the audio input, change the [Audio Input] on the Setting Page (see "Operation Guide" > "Audio Input"). LINE IN is selected by default. Input terminal: 3.5 mm ( 0.14 in.) mini-jack (monaural) • Dynamic MIC IN Input impedance: 1.75 kΩ ±20% * Supported microphones: Output impedance: 400 Ω - 600 Ω • Condenser MIC IN Input impedance (microphone bias resistance): 2.2 kΩ ±20% Microphone power supply: plug-in power (voltage: 1.8 V) * Supported microphones: Condenser microphones with plug-in power support • LINE IN Input level: Max. 1 Vp-p * Use a microphone with an amplifier.  Audio Output Terminal LINE OUT (monaural output) Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from Viewer. Output terminal: 3.5 mm ( 0.14 in.) mini-jack (monaural) Output level: Max. 1 Vp-p * Use a speaker with an amplifier. Important • Using incorrect settings for [Audio Input] may damage the camera and/or microphone. Be sure to configure the settings correctly. • Microphone characteristics may affect volume and sound quality. • Images and audio do not always synchronize properly. • Audio may be interrupted depending on PC characteristics and network environment. • Video and audio can be streamed to up to 30 clients. However, audio may be interrupted when streaming to many clients or using SSL. • Audio may be interrupted when using antivirus software. • Connecting and disconnecting the LAN cable interrupts the audio. Use the viewer to reconnect.