Canon VB-R12VE Network Camera VB-R13VE/VB-R12VE/VB-R11VE/VB-R10VE Installation - Page 2

Connecting the Camera

To prevent cable connections from shorting out, wrap each individual connection with insulating tape, and then

wrap all of the cables with waterproofing tape.

Power Connection

Power can be supplied to the camera in the three ways described below. Please be sure to read the user manual

for the dedicated power supply before use.

Note

• Power supply should conform to all local codes.

• The power supply should also comply with IEC/UL60950-1 (SELV/LPS) standards.



PoE+/PoE (Power over Ethernet)

Power can be supplied to the camera by using a LAN cable connected to a PoE+/PoE HUB that conforms to the

IEEE802.3at Type 2 (PoE+)/Type 1 (PoE) standard.

Important

• Check with your dealer for more information about PoE+/PoE HUB and Midspan technology.

Midspan (a LAN cable power supply device) is a device that, like a PoE+/PoE HUB, supplies power to the camera via a

LAN cable.

• Some PoE+/PoE HUBs allow the limitation of power for each port, but applying limits may interfere with performance. If

using this type of PoE+/PoE HUB, do not limit the operating power.

• Some PoE+/PoE HUBs have limits for the total power consumption for the ports, which can interfere with performance

when multiple ports are in use. For more information, check the instruction guide for your PoE+/PoE HUB.

• When the camera is connected to both a PoE+/PoE HUB and an external power supply (12 V DC or 24 V AC), power will

be supplied in the following order of precedence.

External power supply (24 V AC) > PoE+/PoE HUB > External power supply (12 V DC)

However, when connecting power from both, certain combinations could cause problems such as unstable network

connections. If a problem arises, disable one of the power supplies.



External Power Supply

12 V DC or 24 V AC input can be used. Use the included interface cable to connect to the camera power

connection terminal.

1: BROWN Power 24 V AC / 12 V DC non-polar

2: BLUE

Power 24 V AC / 12 V DC non-polar

3: GREEN

FG (frame ground)

1

3

1

3

12 V DC can be connected in a non-polar configuration.

Important

• The power supply should be within the following voltage range.

• 24 V AC: Voltage fluctuation within ±10% of 24 V AC (50 Hz or 60 Hz ±0.5 Hz or less)

Current supply capacity of at least 2.0 A per camera

• 12 V DC:

Voltage fluctuation within ±10% of 12 V DC

Current supply capacity of at least 1.5 A per camera

• When using a 12 V DC battery power supply, be sure to connect resistors of at least 0.5 – 1.0

Ω

/20 W in series to the

power line.

• For an external power supply, use a double-insulated device.

Recommended Power Cables [Reference]

Cable (AWG)

24

22

20

18

16

12 V DC maximum cable length

m

(ft.)

4

(13.1)

6

(19.7)

10

(32.8)

17

(55.8)

26

(85.3)

24 V AC maximum cable length

m

(ft.)

6

(19.7)

10

(32.8)

15

(49.2)

24

(78.7)

39

(128.0)

Use UL cable (UL-1015 or equivalent) for 12 V DC or 24 V AC wiring.



AC Adapter

Please use the dedicated AC adapter (sold separately).

Remove the power connector attached to the AC adapter, then connect the power interface cable from the power

connector included in the package, as shown in the following diagram.

AC Adapter

Power Interface

Cable

Black

Brown

Blue

Green

White

Insulate

AC Adapter

Power Interface

Cable (Waterproof)

Black

Brown

Blue

Green

White

Insulate

External Device I/O Terminals

External device I/O terminals consist of two input and output systems each. Viewer can be used to check external

device input status and control output to an external device (Please refer to the “Operation Guide”).

Use the included I/O interface cable to connect to external device input/output terminals.

1

8

1: BROWN

External device input 1 IN1 (+)

2: BLACK

External device input 1 IN1 (-)

3: RED

External device input 2 IN2 (+)

4: BLACK

External device input 2 IN2 (-)

5: ORANGE External device output 1 OUT1

6: YELLOW External device output 1 OUT1

7: GREEN

External device output 2 OUT2

8: BLUE

External device output 2 OUT2



External Device Input Terminals (IN1, IN2)

External device input terminals consist of two sets (IN1, IN2) of two terminals, with the negative terminals

connected to the camera interior GND. Connecting cables to the positive and negative terminals and opening or

closing the circuit notifies the Viewer.

Important

• When connecting sensors and switches, connect terminals that are electrically isolated from the respective power and

GND.



External Device Output Terminals (OUT1, OUT2)

External device output terminals consist of two sets (OUT1, OUT2) of two terminals. The sets have no polarity.

Controls from the Viewer can be used to open and close the circuit between the terminals. Using optical couplers,

the output terminals are isolated from the camera’s internal circuit.

The load connected to the output terminals should be within the following rating range.

Rating between output terminals:

Maximum voltage 50 V DC

Continuous load current at or below 100 mA

On resistance: Max. 30

Ω

Audio Input/Output Terminals

Each audio input/output terminal has one input system and one output system.

Connecting the camera to an audio input/output device such as a microphone or a speaker with an amplifier

allows you to send/receive audio through the Viewer.

Use the

3.5 mm (

0.14 in.) monaural mini-jack connector to connect an audio input/output device.



Audio Input Terminal Common LINE IN/MIC IN (monaural input)

Although the camera only has a single audio input system, it supports two types of microphone input: LINE IN and

MIC IN. Before using the audio input, please confirm the [Audio Input] on the Setting Page (please refer to the

“Operation Guide”). LINE IN is selected by default.

Input terminal:

3.5 mm (

0.14 in.) mini jack (monaural)

• Dynamic MIC IN

Input impedance: 1.5 k

Ω

±5%

* Supported microphones: Output impedance: 400 – 600

Ω

• Condenser MIC IN

Input impedance (microphone bias resistance): 2.2 k

Ω

±5%

Microphone power supply: plug-in power (voltage: 2.3 V)

* Supported microphones: Condenser microphones with plug-in power support

• LINE IN

Input level: Max. 1 Vp-p

* Please use a microphone with an amplifier.



Audio Output Terminal LINE OUT (monaural output)

Connect the camera to a speaker with an amplifier. Audio can be sent to the speaker from Viewer.

Output terminal:

3.5 mm (

0.14 in.) mini jack (monaural)

Output level: Max. 1 Vp-p

* Use a speaker with an amplifier.

Internal Connection Diagram

Internal controller

External device

Input terminal

IN1, IN2

Output terminal

OUT1, OUT2

+3.3 V

0.1 µF

10 k

Ω

10 k

Ω

1 k

Ω

External device

When the temperature within the camera is low (heater activated)

When the unit is powered by a 24 V AC/ PoE+ power source, the heater unit can be used.

The heater unit will be activated automatically when the temperature within the camera is low. The orange LED will

be lit, until the camera has warmed up enough to start transferring video. Once the temperature within the camera

has reached the level where it can transfer the video once again, the orange LED will turn off.

Rebooting/Resetting the Camera



Rebooting

To reboot the camera by turning its power off and on, remove the dome

case and press the reboot switch.

Note

Rebooting can be done from the camera settings page as well (please refer to

the “Operation Guide”).



Resetting

To reset the camera to its factory default settings, press the reset switch

and reboot switch while checking the LED (Blue) in the following order.

1) Hold the reset switch down, and press the reboot switch with a pointed

object.

2) After holding down the reset switch for at least three seconds, release

the reboot switch.

3) After the LED (Blue) starts to blink, release the reset switch. When the

blinking has stopped, the unit has finished resetting.

LED (Orange)

LED (Blue)

Reset

switch

Reboot switch

Only for European Union and EEA (Norway, Iceland and Liechtenstein)

These symbols indicate that this product is not to be disposed of with your household waste, according to

the WEEE Directive (2012/19/EU), the Battery Directive (2006/66/EC) and/or national

legislation implementing those Directives.

If a chemical symbol is printed beneath the symbol shown above, in accordance with the

Battery Directive, this indicates that a heavy metal (Hg = Mercury, Cd = Cadmium, Pb =

Lead) is present in this battery or accumulator at a concentration above an applicable

threshold specified in the Battery Directive.

This product should be handed over to a designated collection point, e.g., on an authorized one-for-one

basis when you buy a new similar product or to an authorized collection site for recycling waste electrical and

electronic equipment (EEE) and batteries and accumulators. Improper handling of this type of waste could

have a possible impact on the environment and human health due to potentially hazardous substances that

are generally associated with EEE. Your cooperation in the correct disposal of this product will contribute to the

effective usage of natural resources.

For more information about the recycling of this product, please contact your local city office, waste authority,

approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.

canon-europe.com/battery.

CANON INC.

30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan

CANON EUROPA N.V.

Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands

Specifications

Please refer to the installation procedures or the Appendix – Specifications for specifications not listed below.

Camera

Lens

30x optical zoom (20x digital zoom) lens with auto focus

Viewing Angle

For 16:9 aspect ratios

Horizontal: 62.6° (W) – 2.2° (T)

Vertical:

36.9° (W) – 1.3° (T)


Horizontal: 48.5° (W) – 1.7° (T)

Vertical:

36.9° (W) – 1.3° (T)


Horizontal: 58.4° (W) – 2.1° (T)

Vertical: 34.1° (W) – 1.2° (T)


Horizontal: 58.4° (W) – 2.1° (T)

Vertical: 45.0° (W) – 1.6° (T)

Min. Subject Illumination

Day Mode (color):

0.05 lux (F1.4, shutter speed 1/30 sec., when smart shade control is off, 50IRE)

Night Mode (monochrome):


When using the Dome Unit (Smoked) (sold separately)

Day Mode (color):




Day Mode (color):




When using the Dome Unit (Smoked) (sold separately)

Day Mode (color):




Pan Angle Range

360°continuous panning

Tilt Angle Range

180° (ceiling-mounted position: 0° – 180°)

– When the horizontal direction of the camera is 0°

– When the tilt angle is between angles below, the dome cover can cause a line to appear in the video, as well

as a decline in the video quality

0° – 12° (168° – 180°) (W)

0° – 5° (175° – 180°) (T)

Interface

Network Terminal*

LAN x 1 (RJ45, 100Base-TX (auto/full-duplex/half-duplex))

* Use a category 5 or better LAN cable, 100 m (328 ft.) or less in length.

Audio Input Terminal

3.5 mm (

0.14 in.) mini-jack connector (monaural)

(Common for LINE IN & MIC IN)

LINE IN (connect to an amplifier microphone)

or

MIC IN (connect to a microphone w/o amplifier)

Switch LINE IN/MIC IN in the Setting Page.

Audio Output Terminal

3.5 mm (

0.14 in.) mini-jack connector (monaural)

(LINE OUT)

LINE OUT (connect to an amplifier speaker)

External Device I/O Terminal

Input x 2, Output x 2

Memory Card*

SD Memory Card, SDHC Memory Card, SDXC Memory Card Compatible.

* To insure reliability in the recording speed, it is recommended to use CLASS 10 rated products. Even when

using CLASS 10 products, reliability cannot be guaranteed during heavy access loads (e.g., when recording

and deleting data at the same time).

Others

Operating Environment Temperature

(Includes LAN Connector Set

Operating Temperature Range (including direct sun exposure):

(

Waterproof)

)

AC: -50°C – +55°C (-58°F – +131°F)

PoE+: -35°C – +55°C (-31°F – +131°F)

DC, PoE: -10°C – +55°C (+14°F – +131°F)

Start-up Temperature Range (including direct sun exposure):

AC, PoE+: -30°C – +55°C (-22°F – +131°F)

DC, PoE: -10°C – +55°C (+14°F – +131°F)

Humidity: 5% – 85% (without condensation)

Storage Environment

Temperature: -30°C – +60°C (-22°F – +140°F)

Humidity: 5% – 90% (without condensation)

Installation Method

Ceiling mount/Surface mount

Canon will not guarantee proper operation if the cameras are installed on surfaces where the angle is more than

±5° from horizontal, because this will put a heavy load onto sliding mechanical parts and may affect durability.

Power Supply

PoE: PoE power supply via LAN connector (IEEE802.3at Type1/Type2 compliant)

AC Adapter: PA-V18 (100 – 240 V AC) (sold separately)

External power source: 24 V AC/12 V DC

Power Consumption

PoE+: Max. approx. 22.4 W *

1

PoE: Max. approx. 11.3 W *

2

AC Adapter PA-V18: Max. approx. 13.8 W (100 V AC)

Max. approx. 13.8 W (240 V AC)

DC: Max. approx. 12.3 W

AC: Max. approx. 34.8 W

PoE+: Max. approx. 20.8 W *

1

PoE: Max. approx. 10.1 W *

2

AC Adapter PA-V18: Max. approx. 12.7 W (100 V AC)

Max. approx. 12.8 W (240 V AC)

DC: Max. approx. 11.0 W

AC: Max. approx. 33.2 W

*

1

Class 4 power sourcing equipment (requests 30.0 W)

*

2

Class 0 power sourcing equipment (requests 15.4 W)

Weight

Approx. 3530 g (7.79 lb.)

Approx. 3420 g (7.54 lb.)

Impact Resistance

IK10 (20J)

Dust-resistant/

Waterproof Specification

IP66

Symbols Indicating Safety Precautions

This Installation Guide uses the following symbols to indicate important information the user should know in order

to use the product safely. Explanations are provided for each symbol so that users will understand the level of

importance for each. Be sure to observe these items.

Warning

Failure to follow the instructions accompanied by this symbol may result in death or

serious injury.

Caution

Failure to follow the instructions accompanied by this symbol may result in injury.

Caution

Failure to follow the instructions accompanied by this symbol may result in property

damage.

Safety Precautions

Installation Precautions

Warning

Do not install in the following places:

• Places in strong direct sunlight, near heat-generating objects, or locations subject to high

temperatures

• Places near fire sources or flammable solvents (alcohol, thinner, fuel, etc.)

• Places subject to oily smoke or steam

• Confined or enclosed places

Failure to do so may result in fire or electric shock.

•

Insulate the ends of cables you are not using.

Failure to insulate will cause fire or electric shock.

Notes on Power Supply

•

Only use the dedicated AC adapter (sold separately) for AC power.

• Do not set any heavy objects on the power cable (or the LAN cable for a PoE+/PoE power supply).

• Do not pull, forcibly bend, scratch, or modify the power cable (or the LAN cable for a PoE+/PoE power

supply).

• Do not cover or wrap the AC adapter (sold separately) with cloth or blankets.


Caution

For installation or inspection of this camera, consult the dealer where you purchased the product.

• This installation should be made by a qualified service person and should conform to all local codes.

• When installing, make sure the surface is capable of withstanding the total weight of the camera and

accessories, and sufficiently reinforce if necessary.

• Be sure to use installation screws designed for the type of ceiling the camera is to be installed.

• Periodically check the parts and screws for rust and loosening, in order to prevent injuries and

equipment damage due to falling items.

• Do not install in unstable places, places subject to significant vibration or impact, or places subject to

salt damage or corrosive gas.

• Do not install in places subject to strong winds.

• Do not install where snow can accumulate directly on the camera.

•

Be sure to attach the safety wire when installing the camera.

Failure to do so may result in the camera falling or other accidents.

• Do not touch the edges of metal parts with bare hands.

• Be careful not to get your fingers caught when installing.

Failure to do so may result in injuries.

Caution

• Do not turn the camera rotator by hand.

• Do not install on an unstable surface.

• To maximize shock resistant specifications, do not install on insufficiently strong surfaces or surfaces

subject to significant vibration.

• After turning off the power, do not turn the power on again for at least five seconds.

• Take measures to remove static electricity before performing any procedures.

• If there is condensation, please wait to power on, until the condensation dissipates.

• Please waterproof and dust-proof camera, when installing outdoors.

Failure to do so may result in malfunctions.

• Take care not to damage wiring or piping.

Failure to do so may result in damage to peripheral items.

Important

• We recommend the installation of a lightning arrester (a surge protection device) as a measure against failures caused by

lightning strikes. Please refer to our website for details.

Precautions for Installing the Camera Outdoor

When installing the camera outdoors, observe the following precautions to retain

waterproof/ dustproof capabilities.

•

Completely wrap the cable connections and the ends of

cables you are not using, including the connectors, with waterproof tape

up to the cable jacket, so as not to allow water to enter. Please refer to the

waterproofing explanation sheet for details on how to wrap the waterproofing

tape.

•

Please be sure to use the included LAN Connector Set

(Waterproof).

• If wiring by connecting the camera to the composite pipe, bridge the gap

using Ceiling Mounting Kit (sold separately) or Wall Mounting kit (sold

separately). When connecting the pipe, apply silicon sealant to seal it tightly

after attaching the pipe to prevent water getting in as necessary.

Precautions for Use

Warning

• If you discover defective conditions such as smoke, strange sounds, heat or strange odors,

immediately stop using the camera and contact your nearest dealer.

Fire or electric shock may result from continued use of the product.

• If thunder starts, stop installation or inspection etc. and do not touch the camera or continue

connecting the cable.

• Do not disassemble or modify the camera.

• Do not damage the connecting cable.

• Do not insert foreign objects such as water or metal into the camera.

• Do not use flammable sprays near the camera.

• Do not leave LAN cables, external power supply, or the power connector for the AC adapter (

sold

separately

) connected when the camera is not in use for long periods.

• Do not use flammable solvents such as alcohol, paint thinner or benzine when cleaning the camera.


TORX is the trademark of Acument Intellectual Properties, LLC.

The contents of this guide are subject to change without any prior notice.

External Dimensions

229 (

9.02)

R80 (R3.15)

Unit: mm (in.)

M5

(Accessory mount hole)

27.0 (1.06)

324 (12.76)

290 (11.42)

229 (

9.02)

R80 (R 3.15)

Unit: mm (in.)

M5

(Accessory mount hole)

27.0 (1.06)

324 (12.76)

290 (11.42)

340 (13.39)

Canon VB-R12VE Network Camera VB-R13VE/VB-R12VE/VB-R11VE/VB-R10VE Installation - Page 2

Connecting the Camera, Rebooting/Resetting the Camera, Speciﬁcations, Symbols Indicating Safety

Page 2 highlights