Canon VB-S805D Mark II Plenum Mounting Kit SR30-P-VB Installation Guide

Canon VB-S805D Mark II Manual

Get Canon VB-S805D Mark II PDF manuals and user guides View all Canon VB-S805D Mark II manuals
Add to My Manuals
Save this manual to your list of manuals

Canon VB-S805D Mark II manual content summary:

  • 1
  • 2
Plenum Mounting Kit SR30-P-VB
Installation Guide
Be sure to read the “Safety Precautions” section for correct
use. After reading this Installation Guide, keep it in a readily
accessible location for future reference.
In addition to this “Installation Guide”, please also read the
“Installation Guide” included with the camera.
Caution
Request a professional installer for all
installation work. Never try to install
the camera yourself. Doing so may
result in unforeseen accidents such as
dropping the camera or electric shock.
Symbols Indicating Camera Model
Camera specific functions will be listed using the icons below.
: VB-S30D/VB-S30D Mk II
: VB-S31D/VB-S31D Mk II
: VB-S800D/VB-S805D/VB-S800D Mk II/VB-S805D Mk II
Symbols Indicating Safety Precautions
This Installation Guide uses the following symbols to indicate
important information the user should know in order to use the
product safely. Explanations are provided for each symbol so that
users will understand the level of importance for each. Be sure to
observe these items.
Warning
Failure to follow the instructions
accompanied by this symbol may result
in death or serious injury.
Caution
Failure to follow the instructions
accompanied by this symbol may result in
injury.
Caution
Failure to follow the instructions
accompanied by this symbol may result
in property damage.
Safety Precautions
Installation Precautions
Warning
Do not install in the following places:
• Places in direct sunlight, near heat-generating objects, or
subject to high temperatures
• Places near fire sources or flammable solvents (alcohol,
thinner, fuel, etc.)
• Humid or dusty places
• Places subject to oily smoke or steam
• Places subject to sea air
• Confined or enclosed places
Failure to do so may result in fire or electric shock.
Precautions for the LAN (power) cable:
• Do not set any heavy objects on the LAN cable.
•
Do not pull, forcibly bend, scratch, or modify the LAN cable.
Failure to do so may result in fire or electric shock.
Caution
For installation or inspection of this camera, consult the
dealer where you purchased the product.
• This installation should be made by a qualified service
person and should conform to all local codes.
• When installing, make sure the surface is capable
of withstanding the total weight of the camera and
accessories, and sufficiently reinforce if necessary.
• Be sure to use installation screws designed for the type of
surface the camera is to be installed.
• Periodically check the parts and screws for rust and
loosening, in order to prevent injuries and equipment
damage due to falling items.
• Do not install in unstable places, places subject to
significant vibration or impact, or places subject to salt
damage or corrosive gas.
• Be sure to attach the safety wire when installing th
e
camera.
• Use only with compatible cameras.
• If a ceiling plate thickness is not between 10.0 and
50.0 mm, do not use it.
Failure to do so may result in the camera falling or other
accidents.
• Do not touch the edges of metal parts with bare hands.
• Be careful not to get your fingers caught when installing.
Failure to do so may result in injuries.
Caution
•
Do not turn the camera rotator by hand.
•
Do not install on an unstable surface. Also, make
sure the camera is installed ±5° or less horizontal.
• After turning off the power, do not turn the power on again
for at least five seconds.
• Take measures to remove static electricity before
performing any procedures.
• If there is condensation, please wait to power on, until the
condensation dissipates.
Failure to do so may result in malfunctions.
• Take care not to damage wiring or pipes.
Failure to do so may result in damage to peripheral items.
Important
We recommend the installation of a lightning arrester (a surge
protection device) as a measure against failures caused by lightning
strikes. Please refer to our website for details.
Precautions for Use
Warning
• If you discover defective conditions such as smoke,
strange sounds, heat or strange odors, immediately stop
using the camera and contact your nearest dealer.
Fire or electric shock may result from continued use of the product.
• If thunder starts, stop installation or inspection etc. and do
not touch the camera or continue connecting the cable.
• Do not disassemble or modify the camera.
• Do not damage the connecting cable.
• Do not spray the camera with water, or otherwise make it
wet.
• Do not insert foreign objects such as water or metal into
the camera.
• Do not use flammable sprays near the camera.
• Do not leave LAN cables connected when the camera is
not in use for long periods.
• Do not use flammable solvents such as alcohol, paint
thinner or benzine when cleaning the camera.
Failure to do so may result in fire or electric shock.
Main Specifications
Model
SR30-P-VB
Weight
Approx. 900 g (1.99 lb.) (Plenum Mounting Unit, Recessed
Mounting Cover)
TORX is the trademark of Acument Intellectual Properties, LLC.
The contents of this guide are subject to change without any
prior notice.
External Dimensions
158 (6.22)
166 (6.54)
76 (2.99)
12 (0.47)
136 (5.35)
170 (6.09)
Unit : mm (in.)
Before Installing the Camera
Remove the tape affixed on the unit from the factory.
Attach the camera to the camera holder.
1
❶
❷
❸
2
3
a
a.
Camera holder
4
M4 x 3
Screws
(included)
BIE-7204-000
© CANON INC. 2017
Printed in Taiwan
Check Included Items
Plenum Mounting Unit
Recessed Mounting Cover
Sticker
Screws (M4) x 3
Template
Installation Guide (This document)
ENGLISH