Canon imageCLASS MF3110 Service Manual - Page 98
Canon imageCLASS MF3110 Manual
View all Canon imageCLASS MF3110 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 98 highlights
Chapter 3ޓ 3.5.4.11 Removing the Power [2] Supply Shield Plate 0007-7851 1) Remove the 5 screws [1] to remove the power supply shield plate [2]. [2] [1] [1] F-3-197 3.5.4.12 Removing the Power Supply Assembly 0007-7852 1) Remove the 3 screws [1]. 2) Remove the 4 connectors [2] as well as the flat cable [3] on the ECNT board. [1] [2] F-3-198 [3] [2] [1] 3) As you remove the bosses on both sides [1], lower the front part of the power supply assembly [2]. Then pull it to remove the power supply assembly. [1] F-3-199 3.5.4.13 Removing the Gear Unit 0007-7853 1) Remove the 2 screws [1], and detach the drive plate (small) [2]. [2] [1] F-3-200 2) Remove the 2 gears [1]. 3) While freeing the claw, detach the gear unit [2]. [2] [1] F-3-201 3-50
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
Chapter 3
±
3-50
3.5.4.11
Removing the Power
Supply Shield Plate
0007-7851
1) Remove the 5 screws [1] to remove the power
supply shield plate [2].
F-3-197
3.5.4.12
Removing the Power
Supply Assembly
0007-7852
1) Remove the 3 screws [1].
2) Remove the 4 connectors [2] as well as the flat
cable [3] on the ECNT board.
F-3-198
3) As you remove the bosses on both sides [1], lower
the front part of the power supply assembly [2].
Then pull it to remove the power supply assembly.
F-3-199
3.5.4.13
Removing the Gear
Unit
0007-7853
1) Remove the 2 screws [1], and detach the drive plate
(small) [2].
F-3-200
2) Remove the 2 gears [1].
3) While freeing the claw, detach the gear unit [2].
F-3-201
[1]
[1]
[2]
[1]
[2]
[2]
[1]
[3]
[1]
[2]
[2]
[1]
[2]
[1]