Canon imageFORMULA DR-3080CII Color Easy Start Guide - Page 2

☞Continued from front side Connecting the Scanner to Your PC The scanner can be connected to a computer in two ways: by USB connection to a standard USB port on the computer, or by SCSI connection to a SCSI card installed in one of the computer's expansion slots. Select a connection method appropriate to your computing environment. 6-2 Connect the scanner to your computer with the SCSI cable. 4$4*
DBCMF
JT
OPU
TVQQMJFE
"DRVJSF
B
4$4*
DBCMF
CFGPSFIBOE
UIBU NBUDIFT
UIF
TIBQF
PG
UIF
DPOOFDUPST
PO
ZPVS
4$4*
DBSE
BOE
UIF TDBOOFS Note ● For Windows XP, a balloon help pop-up appears when installation is finished. ● The installation finished message does not appear in Windows 98SE/Me/2000. ● The scanner is registered on the computer as "CANON DR-3080CII USB" (or "CANON DR-3080CII SCSI") in the "Imaging Device" directory of the Device Manager. Power Connector SCSI ID Dip Switches USB Connector SCSI Connector (Half-pitch 50-pin, pin-type) Warning ❏ Windows NT does not support the USB interface. Use a SCSI connection with Windows NT. ❏ Do not use both a USB connection and a SCSI connection at the same time. ❏ Use only the supplied power cord. ❏ Connect the scanner to your computer while the scanner is turned OFF. ❏ Before connecting the scanner with a SCSI cable, turn your computer OFF. ❏ A SCSI cable is not supplied. Acquire a SCSI cable beforehand that matches the shape of the connectors on your SCSI card and the scanner. 1. When connecting the scanner with a SCSI cable, turn your computer OFF. 2. Make sure the scanner's power switch is in the OFF position. If the power switch is in the ON position, press the switch to turn it to the OFF position. Power Switch OFF Position ON Position 3. Plug the power cord into the power connector on the rear of the scanner (1). 4. Plug the power cord into the power outlet (2). 5. When connecting the scanner with a USB cable, use the supplied USB cable. Type A Type B Insert the plug with the mark facing down. 6. Follow the steps below when connecting the scanner to your computer with a SCSI cable. 6-1 Turn OFF your computer. .BLF
TVSF
ZPVS
DPNQVUFS
JT
UVSOFE
0''
CFGPSF
DPOOFDUJOH
UIF
4$4* DBCMF Warning ❏ When using the scanner in a daisy chain connection with other SCSI devices, pay attention to the following points: ● The default setting for the SCSI ID is "SCSI ID=2." Set the dip switches so that the scanner's SCSI ID is different from all other SCSI devices on the chain. Dip Switches 12 ON OFF Default Position (SCSI ID=2) 4$4 48
0''
0/
0''
0/ 48
0''
0''
0/
0/ ● The scanner has a built-in SCSI terminator that is permanently set to [ON]. When using the scanner in a daisy chain connection, make sure that it is connected as the terminating device and that the terminators of all other SCSI devices in the chain have been set to [OFF]. The scanner is now connected to your computer. Next, you need to turn on the scanner and ensure Windows recognizes it. (☞STEP5) Turning On the Power (Scanner Recognition) When you turn on the DR-3080CII in a Windows 98SE/Me/2000/XP environment, Windows uses the Plug and Play feature to recognize the scanner and automatically installs the necessary driver. (Windows NT does not have a scanner recognition feature.) Warning ❏ When the scanner is connected by a SCSI cable, always turn on the scanner before the computer. Turning on the computer first may prevent it from recognizing the scanner properly. ❏ Be sure to log on with Administrator privileges when logging on to Windows NT/2000/XP. ❏ Wait at least 10 seconds before turning the scanner on again after turning it off. ❏ If the scanner will not be used for an extended period, be sure to unplug it from the power outlet for safety. 1. Check the connection between the scanner and the computer. 2. Press the power switch to turn the scanner ON (when connecting by SCSI). The power indicator and start key indicator both light green. 3. Turn ON your computer. Power indicator Power Switch On Position 4. Windows recognizes the DR-3080CII as new hardware and performs installation automatically. (Windows98/Me/2000) (WindowsXP) ● When you restart your computer, the scan panel icon remains resident in the task tray. For details, refer to "About the scan panel" on page 35 of the User's Guide. Scan Panel The scanner is now correctly recognized by your computer. Next, you need to select the scanner with the scanning software. (☞STEP6) Selecting the Scanner You must select your scanner before using it with an ISIS- or TWAIN-compatible scanning application. The menus and procedures for selecting the scanner are different for each application. For details, refer to the manual for your scanning application when selecting the scanner. This section explains the procedure for selecting the scanner with "CapturePerfect 3.0". For details on how to use CapturePerfect 3.0, refer to the "CapturePerfect 3.0 Operation Guide" in the Programs menu of Windows. 1. Launch CapturePerfect 3.0 from the Programs menu in Windows. 2. Select [Select Scanner] from the Scan menu. The Scanner Selection dialog box appears. 3. Select [Canon DR-3080CII] and click [OK]. The setup is now complete This completes the setup of the DR-3080CII. Details on how to use the DR-3080CII are described in the User's Guide packaged with the scanner. Before you start using the scanner, make sure to thoroughly read the User's Guide.