Carvin LS1202 Instruction Manual - Page 2
Way Systems Specs, Way Systems Specs, Subwoofer Systems
View all Carvin LS1202 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. THIS UNIT CONTAINS HIGH VOLTAGE INSIDE! REFER SERVICING TO A QUALIFIED TECHNICIAN IMPORTANT! FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING: WATER AND MOISTURE: Do not expose this appliance to rain or moisture. Do not use this apparatus near water (in a wet basement, near a swimming pool, bathtub etc). Care should be taken so that liquids are not spilled or splashed onto the unit. Do not place objects filled with liquids such as beverage containers on this apparatus. POWER SOURCES: The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the unit. Unplug during lightning storms. GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polarization means of an appliance is not defeated. POWER CORD: Power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs and the point where they exit from the appliance. The plug or power inlet is the disconnect device and shall remain readily operable. PLACEMENT: Do not block ventilation openings. Do not install near heat sources such as radiators, stoves or other products that produce heat. Do not install in a confined area. Use only mounting hardware such as brackets and tripods recommended by the manufacturer. SERVICING: The user should not attempt to service the unit. All servicing should be referred to qualified service personnel. FUSING: If your unit is equipped with a fuse receptacle, replace only with the same type fuse. Refer to replacement text on the unit for correct fuse type. LIMITED WARRANTY Your Carvin product is guaranteed against failure for 3 YEARS unless otherwise stated. Carvin will service and supply all parts at no charge to the customer providing the unit is under warranty. Shipping costs are the responsibility of the customer. CARVIN DOES NOT PAY FOR PARTS OR SERVICING OTHER THAN OUR OWN. A COPY OF THE ORIGINAL INVOICE IS REQUIRED TO VERIFY YOUR WARRANTY. This warranty does not cover, and no liability is assumed, for damage due to: natural disasters, accidents, abuse, loss of parts, lack of reasonable care, incorrect use, or failure to follow instructions. This warranty is in lieu of all other warranties, expressed or implied. No representative or person is authorized to represent or assume for Carvin any liability in connection with the sale or servicing of Carvin products. CARVIN SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. When RETURNING merchandise to the factory, you must call for a return authorization number. If your unit is out of warranty, you will be charged the current FLAT RATE for parts and labor to bring your unit up to factory specifications. HELP SECTION 1) UNIT WILL NOT TURN ON: Check the power to the AC cord. Check for tripped circuit breakers, unplugged extension cords or power-strip switches that may be turned off. Check the fuse or circuit breaker on the unit if available. If the fuse has been replaced with the proper value and the fuse fails again, or the internal circuit breaker activates after reset, the unit will require servicing. 2) NO OUTPUT with POWER light ON: Shipping damage will be the primary reason for your product to not function properly. Please give us a call to help you determine the problem. 3) KEEP YOUR UNIT LOOKING NEW: Use only a dry cloth to wipe the control and venting areas. Surfaces without openings may be cleaned with a damp cloth. 2-way SystemS Specs: LS1002 Frequency Response +/- 3dB 85Hz - 20kHz (72Hz - 10dB) Power Capacity Sensitivity Calculated Max SPL Nominal Directivity Nominal Impedance 200 W continuous, 400 W peak 98 dB SPL, 1W / 1M 124 dB 60 degrees HxV 8 Ohms LS1202 Frequency Response +/- 3dB 76Hz - 18kHz (70Hz - 10dB) Power Capacity Sensitivity Calculated Max SPL Nominal Directivity Nominal Impedance 300 W continuous, 600 W peak 97 dB SPL, 1W / 1M 125 dB 90 degrees HxV 8 Ohms LS1502 / 1502A 53Hz - 18kHz 47Hz - 10dB) / 350w RMS (Hi Freq: 50w @ 16 ohms, Lo Freq. 300w @ 8 ohms) 400 W continuous, 800 W peak 100 dB SPL, 1W / 1M 129 dB 90 degrees HxV 8 Ohms Enclosure Type Enclosure Construction Recommended Power Amp Dimensions Weight Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 200 W - 400W 12.4"W x 11"D x 18"H 23 lbs. BiAmp Impedance Enclosure Type LF 8 Ohms, HF 16 Ohms Vented Bass Reflex Enclosure Construction Recommended Power Amp Dimensions Weight 12mm Baltic birch cross grain laminated plywood 300 W - 600W 15"W x 13.2"D x 24.5"H 33 lbs. LF 8 Ohms, HF 16 Ohms Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 400 W - 800W 18"W x 14"D x 27.5"H 43 lbs. 3-way SystemS Specs: LS1503/1503A Frequency Response +/- 3dB 52Hz - 20kHz (46Hz - 10dB) / 425w RMS (Hi Freq: 50w @ 16ohms, Mid Freq: 75w @ 16 ohms, Lo Freq. 300w @ 8 ohms) Power Capacity Sensitivity Calculated Max SPL Nominal Directivity Nominal Impedance BiAmp Impedance Enclosure Type Enclosure Construction Recommended Power Amp Dimensions Weight 400 W continuous, 800 W peak 101 dB SPL, 1W / 1M 130 dB 90 degrees H x 60 degrees V 8 Ohms LF 8 Ohms, MF/HF 8 Ohms Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 400 W - 800W 18.75"W x 15.5"D x 24"H 58 lbs. LS1523 / 1523A 51Hz - 20kHz (45Hz - 10dB) / 900w RMS (Hi Freq: 80w @ 16 ohms, Mid Freq: 120w @ 8 ohms, Lo Freq. 700w @ 4 ohms) 800 W continuous, 1600 W peak 101 dB SPL, 1W / 1M 133 dB 90 degrees H x 60 degrees V 4 Ohms LF 8 Ohms, MF/HF 8 Ohms Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 800 W - 1600W 22..5"W x 19.75"D x 46.75"H 105 lbs. LS2153 51Hz - 20kHz (45Hz - 10dB) 800 W continuous, 1600 W peak 101 dB SPL, 1W / 1M 133 dB 90 degrees H x 60 degrees V 4 Ohms LF 8 Ohms, MF/HF 8 Ohms Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 800 W - 1600W 16.5"W x 14.75"D x 43.75"H 71 lbs. SUBWOOFER SYSTEMS: LS1801 / 1801A Frequency Response +/- 3dB 35Hz - 150Hz (29Hz - 10dB) / 700w RMS @ 4 ohms Power Capacity 800 W continuous, 1600 W peak Sensitivity Calculated Max SPL Nominal Directivity Nominal Impedance Enclosure Type Enclosure Construction Recommended Power Amp Dimensions Weight 98 dB SPL, 1W / 1M 130 dB N/A 4 Ohms Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 800 W - 1600W 19.5"W x 22"D x 23.5"H 71 lbs. LS1802 30Hz - 150Hz (24Hz - 10dB) 1600 W continuous, 3200 W peak 102 dB SPL, 1W / 1M 137 dB N/A 4 Ohms Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 1600 W - 3200W 39.5"W x 22"D x 23.5"H 119 lbs. LS1802 30Hz - 150Hz (24Hz - 10dB) 1600 W continuous, 3200 W peak 102 dB SPL, 1W / 1M 137 dB N/A 4 Ohms Vented Bass Reflex 12mm Baltic birch cross grain laminated plywood 1600 W - 3200W 39.5"W x 22"D x 23.5"H 119 lbs. The power generated by the APS internal power amps has the capacity to damage the drivers, in which case they would not be covered under warranty.