Carvin TRX12N TRx2000series manual - Page 2
Recommended Biamp Crossover Frequencies, Connecting Trx
![]() |
View all Carvin TRX12N manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 2 highlights
CHOOSING THE CORRECT AMPLIFICATION TRx Loudspeakers are designed to be used with professional power amplifiers capable of producing the correct power into equivalent speaker loads. Care should be taken to avoid amplifier clipping. Due to the fact that music signals have a high peak-to-average "crest" factor, a lesser power amplifier driven into clipping is more likely to damage a speaker than a higher power amplifier used within its ratings. When an amplifier is over driven, its output waveform is clipped or squared off reducing the crest factor. If an amplifier is extremely over driven, the output waveform can approach that of a square wave. Under these extreme conditions, an amplifier is capable of producing far more power than its un-distorted rated power output. Carvin Audio recommends an amplifier capable of producing at least the power rating of the speaker up to 1.5 times the power rating of the speaker. (See TECHNICAL SPECIFICATIONS). Always turn on the amplifiers after the mixer and control systems have been powered on. This will eliminate power peaks due to switch on surges which can damage loudspeakers. When powering down the system, reverse the sequence and switch off the power amplifiers first. TRx2115, TRx2153 & TRx2215 Connection Plate 1. INPUT (4-PIN TWIST-LOC) 1 Full range or bi-amp depending on the position of the BIAMP switch. 2. THROUGH (4-PIN TWIST-LOC) This jack is wired in parallel with the input jack for daisy chaining additional enclosures. 4 3. BIAMP SWITCH Changes between full range or bi-amped inputs. DO NOT use with PIN FLIP. 2 4. PIN FLIP SWITCH NORMAL This cabinet is powered through Twist-Loc pins 1+, 1- Use in Full Range Mode or BIAMP mode. PIN FLIP 3 This cabinet is powered through Twist-Loc pins 2+, 2- Use in Full Range Mode only. DO NOT use in BIAMP mode. With PIN FLIP other cabinets can be daisy chained on the same 4-conductor cable and powered from a different amp/channel on Twist-Loc pins 1+, 1- TRx12N Connection Plate TRx2118, TRx2218, TRx2121 Connection Plate 1. INPUT (4-PIN TWIST-LOC) Full range or bi-amp input depending on the position of the BIAMP switch. 2. THROUGH (4-PIN TWIST-LOC) This jack is wired in parallel with the input jack for daisy chaining additional enclosures. 3. BIAMP SWITCH Changes between full range or bi-amped inputs. 1. INPUT (4-PIN TWIST-LOC) Full range input, external crossover required. TRx2118, TRx2218 & TRx2121 do not have an internal passive crossover. 2. THROUGH (4-PIN TWIST-LOC) This jack is wired in parallel with the input jack for daisy chaining additional enclosures. RECOMMENDED BIAMP CROSSOVER FREQUENCIES Low/High TRx12N 1.75kHz - 3kHz TRx2115 1.75kHz - 3kHz TRx2215 2.5kHz - 4kHz Low/Mid-Hi TRx2153 400Hz - 700Hz Low Pass TRx2118 80Hz - 100Hz TRx2218 80Hz - 100Hz TRx2121 80Hz - 100Hz CONNECTING TRx The rear panels of the the TRx loudspeakers are fitted with 4-pin Twist-Loc connectors. All connectors are wired in parallel. 4 pin 1+ 1- 2+ 2- Bi-amp Passive Low Freq. Positive Positive Input Low Freq. Negative Negative Input High Freq. Positive Through High Freq. Negative Through Subwoofers Positive Input Negative Input Through Through
![](/manual_guide/products/carvin-trx12n-trx2000series-manual-67c7042/2.png)