Cisco 2431 Software Configuration Guide

Cisco 2431 - IAD Router Manual

Get Cisco 2431 - IAD Router PDF manuals and user guides
UPC - 746320759852
View all Cisco 2431 manuals
Add to My Manuals
Save this manual to your list of manuals

Cisco 2431 manual content summary:

  • Cisco 2431 | Software Configuration Guide - Page 1
    Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED
  • Cisco 2431 | Software Configuration Guide - Page 2
    are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0809R) Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide Copyright © 2003 - 2008 Cisco Systems, Inc. All rights reserved.
  • Cisco 2431 | Software Configuration Guide - Page 3
    Interface Configuration 2-6 Serial Interface Configuration 2-7 T1/E1 Channelized Mode 2-9 Configuring a 1-Port, 4-Wire 56-kbps DSU/CSU Card 2-11 Choosing Circuit-Switched or Dedicated-Line Service 2-11 Switched Mode 2-12 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide iii
  • Cisco 2431 | Software Configuration Guide - Page 4
    R Configuring Voice over IP 4-1 Prerequisites 4-1 Configuring the Voice Interface 4-2 VoIP Configuration Examples 4-4 FXS-to-FXS Connection 4-4 Configuration for IAD-1 4-5 Configuration for Router RLB-w 4-5 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide iv OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 5
    System B-10 Using the ROM Monitor C-1 Entering the ROM Monitor Mode C-1 ROM Monitor Commands C-2 Command Descriptions C-3 Recovering Boot and System Images C-4 Using the xmodem Command C-4 Using the tftpdnld -r Command C-5 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 6
    the Configuration Register Manually C-6 Changing the Configuration Register Using Prompts C-6 Console Download C-7 Command Description C-7 Error Reporting C-8 Debug Commands C-8 Exiting the ROM Monitor C-9 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide vi OL-4306
  • Cisco 2431 | Software Configuration Guide - Page 7
    of router-based internetworking, but who might not be familiar with Cisco IOS software • System administrators who are responsible for installing and configuring internetworking equipment, and who are familiar with Cisco IOS software OL-4306-03 Cisco IAD2430 Series Integrated Access Devices
  • Cisco 2431 | Software Configuration Guide - Page 8
    over T1/E1 CAS, foreign exchange office (FXO), and foreign exchange station (FXS) interfaces for your router. Cisco IAD2430 Series Configuration Examples Provides a variety of configuration examples: • Cisco IAD2431-8FXS • Cisco IAD2431-16FXS • Cisco IAD2430-24FXS • Cisco IAD 2431-1T1/E1 with
  • Cisco 2431 | Software Configuration Guide - Page 9
    as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide ix
  • Cisco 2431 | Software Configuration Guide - Page 10
    Preface Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide x OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 11
    exchange station (FXS) ports with two 10/100BASE-T ports. The chassis has the following interfaces: • RJ-21 analog voice interface • Two 10/100BASE-T ports • External flash memory • AC and DC power inputs OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-1
  • Cisco 2431 | Software Configuration Guide - Page 12
    -21 analog voice interface • One T1/E1 port • One 10/100BASE-T port • One WIC/VIC slot • External flash memory • AC and DC power adapter Figure 1-3 Cisco IAD2431-8FXS Chassis-Back Panel 88825 IAD2431-8FXS Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-2 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 13
    (see Figure 1-5): • One T1/E1 ports • Two 10/100BASE-T ports • One WIC/VIC slot • External flash memory • AC and DC power inputs Figure 1-5 Cisco IAD2431-1T1E1 Chassis-Back Panel IAD2431-1T1E1 88827 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-3
  • Cisco 2431 | Software Configuration Guide - Page 14
    • One T1/E1 port • Two Fast Ethernet ports • AC and DC power inputs Figure 1-7 Cisco IAD2435-8FXS Chassis-Back Panel FXS IAD2435-8FXS WAN FastEthernet CONSOLE T1/E1 0/1 0/0 AUX 12V DC SA 231873 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-4 OL
  • Cisco 2431 | Software Configuration Guide - Page 15
    following: • Getting Help, page 1-6 • Command Modes, page 1-7 • Undoing a Command or Feature, page 1-8 • Saving Configuration Changes, page 1-8 • Where to Go Next, page 1-10 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-5
  • Cisco 2431 | Software Configuration Guide - Page 16
    the command followed by a space and a question mark: Router> show ? • To redisplay a command you previously entered, press the Up arrow key. You can continue to press the Up arrow key for more commands. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-6 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 17
    Router(config-controller)# exit Router(config)# exit Router# %SYS-5-CONFIG_I: Configured from console by console The last message is normal and does not indicate an error. Press Enter to get the Router# prompt. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 18
    , see Appendix B, "Formatting the Flash Memory." Note To simplify network operations and management of Cisco IOS software migration, see the Basics of a Successful Cisco IOS Software Migration document. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-8 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 19
    T1/E1 WAN Interface with Analog FXS User Interface Ethernet WAN T1 IAD Cisco IAD model number: IAD2431-8FXS IAD2431-16FXS IAD2432-24FXS IAD2435-8FXS RJ-21 Analog telephones Distribution panel 88998 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 1-9
  • Cisco 2431 | Software Configuration Guide - Page 20
    save your configuration changes to NVRAM so that the changes are not lost if there is a system reload or power outage. Go to Chapter 2, "Using the setup Command Facility," to begin configuring the router. 1-10 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 21
    This chapter describes how to use the setup command facility to configure your Cisco integrated access device (IAD). The setup command facility prompts you to enter information needed to start a router functioning quickly. The facility steps you through a basic configuration, including LAN and WAN
  • Cisco 2431 | Software Configuration Guide - Page 22
    support interface cards. System Bootstrap, Version 12.4(20080418:075150) [BLD-iad.IAD_APRIL18_POST_SYNC_BUILD_UBLDIT-for_gopasaha 102], DEVELOPMENT SOFTWARE Copyright (c) 1994-2008 by cisco Systems, Inc. C2431 platform with 262144 Kbytes of main memory Cisco IAD2430 Series Integrated Access Devices
  • Cisco 2431 | Software Configuration Guide - Page 23
    FastEthernet interfaces 8 Voice FXS interfaces 256K bytes of non-volatile configuration memory. 126000K bytes of ATA Flash (Read/Write) --- System Configuration Dialog --- Would are in square brackets '[]'. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-3
  • Cisco 2431 | Software Configuration Guide - Page 24
    for the Cisco IAD: Configuring global parameters: Enter hostname [Router]: IAD2435 The enable secret is a password used to protect access to privileged Configure RIP routing? [yes]: n Configure CLNS? [no]: Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-4 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 25
    installed in your Cisco IAD. Note The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards. The are hardware on the router that you connect directly to a T1 or E1 line from your Telco. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-5
  • Cisco 2431 | Software Configuration Guide - Page 26
    EXEC mode. Enters global configuration mode. Enters the configuration mode for a Fast Ethernet WAN interface on the router. Sets the IP address and subnet mask for the specified Fast Ethernet interface. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-6 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 27
    appropriate for your interface card and network. Note The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards. The messages you see may vary. 24 subnet bits; mask is /24 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-7
  • Cisco 2431 | Software Configuration Guide - Page 28
    specified protocol. Enter the DLCI number for this interface [16]: Do you want to map a remote machine's IP set in dce mode. The following clock rates are supported on the serial interface. 0 1200, 2400, 4800 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-8 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 29
    Cisco IOS commands generated by a typical serial configuration: interface Serial0/0 encapsulation ppp clock rate 2000000 ip address 2.0.0.1 255.0.0.0 T1/E1 Channelized Mode The following is an example of a T1 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-9
  • Cisco 2431 | Software Configuration Guide - Page 30
    the setup Command Facility T1 is capable of exactly match the remote router's password. Frame specified protocol. Enter the DLCI number for this interface [16]: Do you want to map a remote machine's IP address Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 31
    at the end of each day. Dedicated service is ideal for heavy network traffic. Dedicated service is ideal if you need a constant network connection or you need connection for more than eight hours per day. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 2-11
  • Cisco 2431 | Software Configuration Guide - Page 32
    can be choose only when connected back to back. Serial interface needs clock rate to be set in dce mode. The following clock rates are supported on the serial interface. auto, 2.4, 4.8, 9.6, 19.2, 38.4 2-12 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 33
    : Router> enable Password: password Router# setup • Modify the existing configuration or configure additional features with the CLI as described in Chapter 3, "Configuring with the Command-Line Interface." OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 34
    Completing the Configuration Chapter 2 Using the setup Command Facility 2-14 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 35
    and read it now. The chapter contains important information that you need for configuring your Cisco IAD. Note The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-1
  • Cisco 2431 | Software Configuration Guide - Page 36
    allows you to distinguish multiple Cisco IADs and routers from each other. Setting Router>), you must enter the enable secret password to gain access to configuration mode. Substitute your enable secret password for guessme. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 37
    top of the command output. Exit global configuration mode and attempt to reenter it, using the new enable password: Router# exit . . . Router con0 is now available Press RETURN to get started. Router> enable OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-3
  • Cisco 2431 | Software Configuration Guide - Page 38
    Cisco IAD. To configure Fast Ethernet interfaces, perform the following steps. SUMMARY STEPS 1. enable 2. configure terminal 3. ip routing 4. interface type number 5. ip address ip address subnet mask 6. exit 7. Ctrl-z Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 39
    Router(config-if)# ip address 172.16.74.3 255.255.255.0 exit Step 7 Example: Router(config-if)# exit Ctrl-z Example: Router the Cisco IAD2430 IAD, including onboard T1/E1 or VWIC T1/E1, participate in the system clock Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-5
  • Cisco 2431 | Software Configuration Guide - Page 40
    Line Interface To have the T1/E1 controller participate as a clock source for the Cisco IAD system clock domain and to system clock domain. Enters both parts of the VWIC controller at slot 0 into the system clock domain. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 41
    route, you might need to enter additional configuration commands. Before you begin configuring the interfaces, make sure to do the following: • Connect a console to the Cisco IAD. • Power on the Cisco IAD. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-7
  • Cisco 2431 | Software Configuration Guide - Page 42
    Channel Groups on T1/E1 to Support Data To support data, use the following procedure to configure a new T1/E1 interface for channelized T1/E1 (CT1) or the "Port Numbering Conventions" section on page 1-5. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-8 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 43
    address 10.1.15.1 255.255.255.0 exit Exits to global configuration mode. Step 14 Example: Router(config-if)# exit Ctrl-z Example: Router# Returns to enable mode when you finish configuring interfaces. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-9
  • Cisco 2431 | Software Configuration Guide - Page 44
    required for your global configuration. This example uses IP routing. Selects the DSL interface to configure. Controller numbers vary. See Port Numbering Conventions, page 1-5. 3-10 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 45
    • Configuring Switch Types for ISDN PRI Q.931 Support • Configuring DS0 Groups for CAS For more information on configuring ISDN voice interfaces, see the Basic ISDN Voice-Interface Configuration document. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-11
  • Cisco 2431 | Software Configuration Guide - Page 46
    t1/e1 slot/port Example: Router(config)# controller t1 0/2 Purpose Enters privileged EXEC mode. Enters global configuration mode. (Optional; see note.) Selects a service for slot and port are 0 and 1. 3-12 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 47
    description calls to PSTN - dial 9 from FXS destination-pattern 9T port 0/0:23 ! dial-peer voice 2 pots direct-inward-dial description calls to Analog phone from PSTN destination-pattern 4083333333 port 0/1/0 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 48
    the T1/E1 trunk to support signaling that matches the PBX signaling type: • cas-Channel-associated signaling • Common channel signaling cross-connect-CCS cross-connect for bearer channels • ccs frame-forwarding-CCS transparent signaling 3-14 Cisco IAD2430 Series Integrated Access Devices Software
  • Cisco 2431 | Software Configuration Guide - Page 49
    11 Example: Router(config-voice-port)# no shutdown Exit voice-port configuration mode and repeat Step 5 through Step 8 for the remaining digital voice ports. Configures any required digital voice ports. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-15
  • Cisco 2431 | Software Configuration Guide - Page 50
    (2) an analog FXS port and a DS0 group on a T1. Cross-connecting is done differently for data and voice, as shown in the following procedures: • Configuring TDM to TDM • Configuring TDM to Analog Voice Port 3-16 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306
  • Cisco 2431 | Software Configuration Guide - Page 51
    TDM-group number under the same controller. Configures a TDM channel group for T1/E1. When configuring cross-connect for data traffic only, do not specify the type mode. Example: Router(config-if)# exit OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-17
  • Cisco 2431 | Software Configuration Guide - Page 52
    Configures cross-connect between the analog FXS port and the DS0 group on the T1/E1. Configuring TDM to Physical Serial Interface Perform the following steps to configure TDM connect for serial interface. 3-18 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 53
    T1/E1 Interfaces Note The serial interface must be a DTE device. Router(config-controller)# interface serial 1/0:0 no keepalive Sets the no keepalive function. Example: Router(config-if)# no keepalive OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 54
    subnet mask 6. half-duplex timer dcd-drop-delay value 7. clockrate value 8. dce-terminal-timing-enable 9. invert-txc 10. nrzi-encoding 11. exit 12. Ctrl-z 3-20 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 55
    T1/E1 Serial WAN Interface Card DETAILED STEPS Command or Action Step 1 enable Purpose Enters privileged EXEC mode. Step 2 Example: Router used in DTE mode, the Cisco IAD automatically uses the external timing Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-21
  • Cisco 2431 | Software Configuration Guide - Page 56
    -duplex timer rts-drop-delay half-duplex timer rts-timeout half-duplex timer transmit-delay Default Setting (Milliseconds) 100 5000 100 100 100 2000 0 3-22 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 57
    Chapter 3 Configuring with the Command-Line Interface Configuring a WIC-1DSU-T1/E1 Serial WAN Interface Card Table 3-2 Clock Rate Settings for 1-Port/2- (bits per second) 64000 72000 115200 128000 - - OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-23
  • Cisco 2431 | Software Configuration Guide - Page 58
    the following mandatory voice-port parameters: a. Connection b. Dial type c. Signal type d. Call progress tone (Optional) Configure a description. Perform the following steps to configure FXO voice ports. 3-24 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 59
    5. dial-type 6. signal 7. compand-type 8. cptone local 9. description string 10. exit 11. Ctrl-z DETAILED STEPS Command or Action Step dtmf. Example: Router(config-voice-port)# dial-type pulse OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-25
  • Cisco 2431 | Software Configuration Guide - Page 60
    voice-port values are adequate for FXS voice ports. Note The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards. If you need parameters: a. Connection b. Dial type 3-26 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 61
    , page 1-5. Configures the signaling type for analog FXS voice ports. The default is loop-start. Configures the companding standard used to convert between analog and digital signals in PCM systems. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-27
  • Cisco 2431 | Software Configuration Guide - Page 62
    T1-WAN Ports If your Cisco IAD has a T1-WAN port, a default ATM configuration is automatically enabled when you enter the mode atm controller command. Note The Cisco IAD2435 router does not support . 3-28 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 63
    logical ATM interface 0. Controller framing is automatically set to Extended SuperFrame (ESF). The linecode is automatically set to binary 8-zero substitution (B8ZS). OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-29
  • Cisco 2431 | Software Configuration Guide - Page 64
    Router(config-ctrl)# exit interface type number Step 7 Example: Router(config)# interface atm 0 ip address ip address subnet mask Step 8 Example: Router(config-if)# ip address 172.16 size in cells. 3-30 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 65
    16 Example: Router(config-if-vc)# exit Repeat Step 8 through Step 12 for each additional ATM PVC to be configured. no shutdown Configures any additional ATM PVCs. Activates the ATM interface. Step 17 Example: Router Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-31
  • Cisco 2431 | Software Configuration Guide - Page 66
    ADSL/SHDSL WAN interface card. SUMMARY STEPS 1. enable 2. configure terminal 3. interface atm slot/port 4. ip address ip address subnet mask 5. pvc name vpi/vci 3-32 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 67
    is ATM adaption layer 5+ (AAL5+), Logical Link Control Protocol (LLC), Subnetwork Access Protocol (SNAP). (Optional) Enables IP connectivity and creates a point-to-point IP address for the VC. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-33
  • Cisco 2431 | Software Configuration Guide - Page 68
    -dmt} Example: Router(config-if)# dsl operating-mode adsl2+ annex m Configure the ADSL/SHDSL interface to operate in a specified mode: • ansi-dmt-ANSI full rate mode per T1.413 (ITU configuration mode. 3-34 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 69
    which interfaces are having trouble, use the debug atm not set Keepalive not supported Encapsulation(s):AAL5 PVC mode of "show interface" counters 03:16:00 Queueing strategy:fifo Output Router# show atm vc OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 70
    The Cisco IAD2435 router is a fixed-configuration router and does not support interface cards. BRI VICs present an ISDN S/T physical interface that connects to a network termination (NT) or terminal equipment (TE) device. With ISDN BRI VICs, you can connect a Cisco IAD2431 or IAD2432 series IAD to
  • Cisco 2431 | Software Configuration Guide - Page 71
    Router(config)# interface bri 0/0 no ip address Changes to interface configuration mode for port 0 in slot 0. Specifies that there is no IP address for this interface. Example: Router(config-if)# no ip address OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 72
    configuration mode. Saving Configuration Changes Perform the following steps to prevent loss of the Cisco IAD configuration. SUMMARY STEPS 1. enable 2. copy running-config startup-config 3. Ctrl-z 3-38 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 73
    Step 2 Example: Router# enable copy running-config startup-config Step 3 Example: Router# copy running-config startup-config Ctrl-z Example: Router# Ctrl-z Saving you finish configuring the interfaces. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 3-39
  • Cisco 2431 | Software Configuration Guide - Page 74
    Saving Configuration Changes Chapter 3 Configuring with the Command-Line Interface 3-40 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 75
    and data trunking • Plain old telephone service (POTS)-Internet telephony gateways For more information on understanding and configuring VoIP, see the Configuring Voice over IP document. Prerequisites Before you can configure your Cisco integrated access device (IAD) to use VoIP, you must first
  • Cisco 2431 | Software Configuration Guide - Page 76
    chapter of your Cisco IAD installation and configuration guide. Power on the Cisco IAD. If the current configuration is no longer valid, after about one minute you see the following prompt: Would you like to enter the initial dialog? [yes/no]: Cisco IAD2430 Series Integrated Access Devices Software
  • Cisco 2431 | Software Configuration Guide - Page 77
    IP traffic. For instructions, see your Cisco IAD hardware installation and software configuration guides or the configuration Router# copy running-config startup-config Building configuration. . . [OK] Router# OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 78
    over serial Router RLB-w Voice port 2/0 Serial port IAD 0/0 IAD-1 128 kbps Router R12-e MLPPP over channelized T1 Serial port 1/0:0 Voice port 2/0 IAD IAD-2 95107 Dial peer 1 POTS Dial peer 2 POTS Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 4-4 OL-4306
  • Cisco 2431 | Software Configuration Guide - Page 79
    over IP VoIP Configuration Examples Configuration for IAD-1 hostname iad-1 ! Create voip dial-peer 10 fair-queue 64 256 36 router igrp 888 network 10.0.0.0 Configuration for Router RLB-w hostname rlb-w ! OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 4-5
  • Cisco 2431 | Software Configuration Guide - Page 80
    Configure IGRP router igrp 888 network 20.0.0.0 network 40.0.0.0 Configuration for IAD-2 hostname iad-2 ! IGRP router igrp 888 network 40.0.0.0 Linking PBX Users with Digital E&M Trunk Lines over T1/E1 CAS Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 4-6 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 81
    !Configure voip dial-peer 2 dial-peer voice 3 voip destination-pattern +527.... session target ipv4:172.16.65.123 !Configure the fastethernet interface interface fe 0/0 ip address 172.16.1.182 no shutdown OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 4-7
  • Cisco 2431 | Software Configuration Guide - Page 82
    -peer 2 dial-peer voice 2 voip destination-pattern +9........... session target ipv4:172.16.65.182 ! Configure the serial interface interface serial 0/0 clock rate 2000000 ip address 172.16.1.123 no shutdown Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide 4-8 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 83
    the previous example (that is, a PSTN gateway using an FXO connection) Router SLC in Salt Lake City is connected directly to the PSTN through an FXO 16.65.182 ! Configure the serial interface interface serial 0/0 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 84
    :172.16.1.123 ! Configure the voice port voice port 2/0 connection plar 14081111111 ! Configure the serial interface interface serial 0/0 ip address 172.16.65.182 no shutdown Chapter 4 Configuring Voice over IP 4-10 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL
  • Cisco 2431 | Software Configuration Guide - Page 85
    maximum-recipients 0 ! ! controller T1 1/0 framing sf linecode ami channel-group 0 timeslots 1-24 ! ! ! interface FastEthernet0/0 ip address 1.3.21.53 255.255.0.0 no ip mroute-cache duplex auto speed auto OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-1
  • Cisco 2431 | Software Configuration Guide - Page 86
    : Cisco IAD2435-8FXS Appendix A Cisco IAD2430 voice-port 2/6 ! voice-port 2/7 ! mgcp mgcp call-agent 1.3.37.1 service-type mgcp version 1.0 ! mgcp profile default ! dial-peer cor custom ! 4 login ! ! end Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-2 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 87
    Cisco 2430-24FXS Sample Configuration: Cisco 2430-24FXS Current configuration : 2612 bytes ! version 12.4(1)T service timestamps debug datetime msec service timestamps log datetime msec no service 53 description cflow1 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-3
  • Cisco 2431 | Software Configuration Guide - Page 88
    13 ! voice-port 2/14 ! voice-port 2/15 ! voice-port 2/16 ! voice-port 2/17 ! voice-port 2/18 ! voice-port 2/19 ! voice-port 2/20 ! voice-port 2/21 ! voice-port 2/22 ! voice-port 2/23 ! mgcp profile default ! Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-4 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 89
    Appendix A Cisco IAD2430 Series Configuration Examples dial-peer cor custom ! ! dial-peer voice 1 pots exec-timeout 0 0 speed 115200 line aux 0 line vty 0 4 login ! end Sample Configuration: Cisco 2430-24FXS OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-5
  • Cisco 2431 | Software Configuration Guide - Page 90
    1 ! interface FastEthernet0/0 ip address 1.3.21.56 255.255.0.0 duplex auto speed auto ip rsvp bandwidth 1 1 ! interface Serial0/0 no ip address encapsulation frame-relay clockrate 2000000 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-6 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 91
    Configuration: Cisco 2431-1T1/E1 with WIC call rsvp-sync ! voice-port 1/1:1 ! mgcp mgcp call-agent 1.3.37.1 service-type sgcp version 1.5 mgcp quarantine mode process loop mgcp timer receive-rtcp 2 line vty 0 4 login ! end Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-7
  • Cisco 2431 | Software Configuration Guide - Page 92
    match ip dscp ef ! ! policy-map CORP-POLICY class voice priority percent 45 class control bandwidth percent 10 class class-default fair-queue ! ! ! interface Multilink1 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-8 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 93
    Examples Sample Configuration: Cisco 2432-24FXS with VIC2-4FXO and QoS OL-4306-03 ip address 12.12.0.1 255.255.0.0 service-policy output CORP-POLICY battery-reversal answer ! voice-port 0/2 battery-reversal answer Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-9
  • Cisco 2431 | Software Configuration Guide - Page 94
    14 ! voice-port 2/15 ! voice-port 2/16 ! voice-port 2/17 ! voice-port 2/18 service-type mgcp version 1.0 mgcp src-cac no mgcp piggyback message ! mgcp profile default ! dial-peer cor custom ! ! ! dial-peer voice 1 voip A-10 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 95
    Appendix A Cisco IAD2430 Series Configuration Examples incoming called-number 4088... destination- line vty 0 4 exec-timeout 0 0 login ! ! end Sample Configuration: Cisco 2432-24FXS with VIC2-4FXO and QoS OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide A-11
  • Cisco 2431 | Software Configuration Guide - Page 96
    Sample Configuration: Cisco 2432-24FXS with VIC2-4FXO and QoS Appendix A Cisco IAD2430 Series Configuration Examples A-12 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 97
    from the ROM monitor. Determining the File System on Flash Memory To determine the file system of external flash memory, enter the show slot0: all command. Note slot0 is not supported on the IAD2435 IAD. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-1
  • Cisco 2431 | Software Configuration Guide - Page 98
    slot0 is not supported on the IAD2435 IAD. External Card with Class C Flash File System The geometry and format information is displayed in this format: Router# show slot0: 93 Base Data Sector 187 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-2 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 99
    Sector 155 Base FAT Sector 93 Base Data Sector 187 Formatting Flash Memory as a Class B Flash File System Use these formatting commands to: • Format flash memory with a Class B flash file system (LEFS) OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-3
  • Cisco 2431 | Software Configuration Guide - Page 100
    ? [confirm] Format operation will destroy all data in "flash:". Continue? [confirm] Enter volume ID (up to 64 chars)[default flash]: Current Low End File System flash card in flash will be formatted into DOS Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-4 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 101
    shows sample output for copying a configuration file to the running configuration in an internal flash memory (flash:): Router# copy flash:my-config2 running-config Destination filename [running-config]? OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-5
  • Cisco 2431 | Software Configuration Guide - Page 102
    space originally occupied by the file: Router# dir slot0: Directory of slot0:/ 1 -rw2 -rw- 6458208 6458208 c2430-is-mz.tmp c2430-is-mz 16056320 bytes total (3139776 bytes free) Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-6 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 103
    AC3FC710 3C018001 AC24C714 3C018001 00000140: AC25C718 3C018001 AC26C71C 3C018001 .ELF a 4 ...T ... .4 b.D .e.l A G. ..H J. ..K J ..K< .b g.J.
  • Cisco 2431 | Software Configuration Guide - Page 104
    or show {flash: | slot0:} command. The following examples show sample outputs for displaying the contents of an external flash memory with a Class C flash file system: Router# dir slot0: Directory of slot0:/ Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-8 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 105
    -mz.tmp? [confirm] Router# dir flash: Directory of flash:/ No files in directory 128094208 bytes total (128094208 bytes free) Rename a File To rename a file in flash memory, use the rename {flash: | slot0:} command. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-9
  • Cisco 2431 | Software Configuration Guide - Page 106
    to display the contents of an internal flash card: Router# more flash:c2430-is-mz.tmp 00000000: 7F454C46 System Create a New Directory To create a directory in flash memory, use the mkdir {flash: | slot0:} command. B-10 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 107
    (121626624 bytes free) Router# rmdir flash:/config/test-config Remove directory filename [/config/test-config]? Delete flash:/config/test-config? [confirm] Removed dir flash:/config/test-config Router# dir flash: Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-11
  • Cisco 2431 | Software Configuration Guide - Page 108
    File and Directory Operations Directory of flash:/config/ No files in directory 128094208 bytes total (121630720 bytes free) Appendix B Formatting the Flash Memory B-12 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 109
    is-mz.tmp 0 Mar 01 2008 23:48:36 config 128094208 bytes total (121630720 bytes free) Router# cd config Router# pwd flash:/config/ Router# cd slot0: Router# pwd slot0:/ Router# cd Router# pwd flash: OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide B-13
  • Cisco 2431 | Software Configuration Guide - Page 110
    File and Directory Operations Appendix B Formatting the Flash Memory B-14 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 111
    series integrated access device (IAD). During normal operation, the ROM monitor helps to initialize the processor hardware and boot the operating system software. You can also use the ROM monitor to help you isolate or rule out hardware problems that you encounter while installing your router. This
  • Cisco 2431 | Software Configuration Guide - Page 112
    the Cisco IOS software. As long as the configuration value is 0x0, you must manually boot the operating system from the console. See the boot command in the "Command Descriptions" of cookie PROM in hex Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide C-2 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 113
    -16 -y ymodem-batch protocol -r copy image to dram for launch -x do not launch on download completion -u upgrade ROMMON, System will reboot after upgrade Resets and initializes the router, similar to a power up. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 114
    redundancy check (CRC-16). • -y-Use Ymodem transfer protocol. • -r-Copy the image to DRAM for launch. • -x-Do not launch image on completion of download. Note The IAD2435 IAD ROMMON supports only -c and -y. Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide C-4 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 115
    for disaster recovery only. Do you wish to continue? y/n: [n]: Enter y to begin downloading the Cisco IOS software image. When the process is complete, the ROM monitor mode prompt appears on your screen. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide C-5
  • Cisco 2431 | Software Configuration Guide - Page 116
    Manually To change the virtual configuration register from the ROM monitor manually, until you reset or reboot the router. The following display shows an image 2-15 = boot system [0]: 0 Configuration Summary Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide C-6 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 117
    from, this function might not be supported by Xmodem. Note The IAD2435 IAD only supports c and y. r Optional. Image is loaded into DRAM for execution. The default is to load the image into flash memory. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide C-7
  • Cisco 2431 | Software Configuration Guide - Page 118
    executed. destination_ Name of the system image file or the system configuration file. In order for the router file_name to recognize it, the 0x00000000 R15 = 0xffffffff R19 = 0xffffffff R23 = 0xffffffff Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide C-8 OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 119
    example: rommon 8> sysret System Return Info: count: 19 router will boot the Cisco IOS image in flash memory. The configuration register will change to 0x2101 the next time the router is reset or power cycled. OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide
  • Cisco 2431 | Software Configuration Guide - Page 120
    Exiting the ROM Monitor Appendix C Using the ROM Monitor C-10 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-03
  • Cisco 2431 | Software Configuration Guide - Page 121
    Analog FXS user interfaces with Metro Ethernet interface 1-5, 1-9 ATM 3-28 B b command C-4 b flash command C-4 boot commands C-4 C Cisco IAD2430-24FXS Chassis 1-2 Cisco IAD2431-16FXS chassis 1-3 Cisco IAD2431-1T1E1 chassis 1-3 Cisco IAD2431-8FXS chassis 1-2 Cisco IAD2432-24FXS chassis 1-4 Cisco IOS
  • Cisco 2431 | Software Configuration Guide - Page 122
    Chassis 1-2 Cisco IAD2431-16FXS Chassis 1-3 Cisco IAD2431-1T1E1 Chassis 1-3 Cisco IAD2431-8FXS Chassis 1-2 I i command C-3 interface configuration command mode 1-7 ISDN PRI interface 3-7, 3-8 K k command C-8 IN-2 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306
  • Cisco 2431 | Software Configuration Guide - Page 123
    Timer Commands 3-22 TDM cross-connect 3-16 TFTP download See also console download U user EXEC command mode 1-7 V virtual configuration register C-6 voice over IP configuration examples 4-4 configuring 4-2 OL-4306-03 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide IN-3
  • Cisco 2431 | Software Configuration Guide - Page 124
    Index FXS-to-FXS connections 4-4 linking PBX users with E&M trunk lines 4-6 PSTN gateway access using FXO connections 4-8 PSTN gateway access using FXO connections in PLAR mode 4-9 X xmodem command C-4, C-7 IN-4 Cisco IAD2430 Series Integrated Access Devices Software Configuration Guide OL-4306-
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Cisco IAD2430 Series
Integrated Access Devices
Software Configuration Guide
THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO
CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS
MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND,
EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY
PRODUCTS.
Text Part Number: OL-4306-03