Cisco 2501 User Guide - Page 67

Using AutoInstall, provided on the TCP/IP host. For more information - flash

Get Cisco 2501 - Router - EN PDF manuals and user guides View all Cisco 2501 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Configuring the Router for the First Time Step 5 Step 6 When you are finished configuring the router, enter the exit command until you return to the privileged EXEC prompt (Router#). To save the configuration changes to NVRAM, enter the copy running-config startup-config command at the privileged EXEC prompt. Router# copy running-config startup-config ******** The router will now boot with the configuration you entered. Using AutoInstall The AutoInstall process is designed to configure the router automatically after connection to your WAN. In order for AutoInstall to work properly, a Transmission Control Protocol/Internet Protocol (TCP/IP) host on your network must be preconfigured to provide the required configuration files. The TCP/IP host may exist anywhere on the network as long as the following two conditions are maintained: 1 The host must be on the remote side of the router's synchronous serial connection to the WAN. 2 User Datagram Protocol (UDP) broadcasts to and from the router and the TCP/IP host must be enabled. This functionality is coordinated by your system administrator at the site where the TCP/IP host is located. You should not attempt to use AutoInstall unless the required files have been provided on the TCP/IP host. For more information, refer to the Cisco IOS configuration guide and command reference publications. Take the following steps to prepare your router for the AutoInstall process: Step 1 Attach the WAN cable to the router. Step 2 Power ON the router. The router will load the operating system image from Flash memory. If the remote end of the WAN connection is connected and properly configured, the AutoInstall process will begin. Configuring the Router 4-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
Configuring the Router
4-13
Configuring the Router for the First Time
Step 5
When you are finished configuring the router, enter the
exit
command until you
return to the privileged EXEC prompt (Router#).
Step 6
To save the configuration changes to NVRAM, enter the
copy running-config
startup-config
command at the privileged EXEC prompt.
Router#
copy running-config startup-config
********
The router will now boot with the configuration you entered.
Using AutoInstall
The AutoInstall process is designed to configure the router automatically after connection
to your WAN. In order for AutoInstall to work properly, a Transmission Control
Protocol/Internet Protocol (TCP/IP) host on your network must be preconfigured to provide
the required configuration files. The TCP/IP host may exist anywhere on the network as
long as the following two conditions are maintained:
1
The host must be on the remote side of the router’s synchronous serial connection to the
WAN.
2
User Datagram Protocol (UDP) broadcasts to and from the router and the TCP/IP host
must be enabled.
This functionality is coordinated by your system administrator at the site where the TCP/IP
host is located. You should not attempt to use AutoInstall unless the required files have been
provided on the TCP/IP host. For more information, refer to the Cisco IOS configuration
guide and command reference publications.
Take the following steps to prepare your router for the AutoInstall process:
Step 1
Attach the WAN cable to the router.
Step 2
Power ON the router.
The router will load the operating system image from Flash memory. If the
remote end of the WAN connection is connected and properly configured, the
AutoInstall process will begin.