Cisco 2610 Hardware Installation Guide - Page 72

Initial Configuration Using SDM, Initial Configuration Using the Setup Command Facility, Ctrl-C, setup

Get Cisco 2610 - Router - EN PDF manuals and user guides
UPC - 746320089614
View all Cisco 2610 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

Configuring the Router Chapter 3 Installing the Router Initial Configuration Using SDM If Cisco Router and Security Device Manager has been installed on your router, the following messages appear at the end of the startup sequence: yourname con0 is now available Press RETURN to get started. For configuration procedures using SDM, refer to the quick start guide that shipped with your router. You can also access the Cisco 2600 series routers quick start guides online at the following URL: http://www.cisco.com/univercd/cc/td/doc/product/access/acs_mod/cis2600/26xx_qsg/index.htm Initial Configuration Using the Setup Command Facility This section shows how to use the setup command facility to configure a hostname for the router, set passwords, and configure an interface for communication with the management network. If you see the following messages at the end of the startup sequence, the setup command facility has been invoked automatically: --- System Configuration Dialog --- At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Would you like to enter the initial configuration dialog? [yes/no]: The setup command facility prompts you for basic information about your router and network, and it creates an initial configuration file.The prompts vary, depending on your router model, the installed interface modules, and the software image. The following example and the user entries (in bold) are shown as examples only. For a description of the interface numbering, see the "Interface Numbering" section on page 1-9. Note If you make a mistake while using the setup command facility, you can exit and run the setup command facility again. Press Ctrl-C, and enter setup at the privileged EXEC mode prompt (Router#). Step 1 Step 2 To proceed using the setup command facility, enter yes when the power-up messages have ended. Would you like to enter the initial configuration dialog? [yes/no]: yes When the following messages appear, press Return to enter basic management setup: At any point you may enter a question mark '?' for help. Use ctrl-c to abort configuration dialog at any prompt. Default settings are in square brackets '[]'. Basic management setup configures only enough connectivity for management of the system, extended setup will ask you to configure each interface on the system Would you like to enter basic management setup? [yes/no]: yes 3-26 Cisco 2600 Series Routers Hardware Installation Guide OL-2171-06

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
3-26
Cisco 2600 Series Routers Hardware Installation Guide
OL-2171-06
Chapter 3
Installing the Router
Configuring the Router
Initial Configuration Using SDM
If Cisco Router and Security Device Manager has been installed on your router, the following messages
appear at the end of the startup sequence:
yourname con0 is now available
Press RETURN to get started.
For configuration procedures using SDM, refer to the quick start guide that shipped with your router.
You can also access the
Cisco 2600 series routers quick start guides
online at the following URL:
Initial Configuration Using the Setup Command Facility
This section shows how to use the setup command facility to configure a hostname for the router, set
passwords, and configure an interface for communication with the management network. If you see the
following messages at the end of the startup sequence, the setup command facility has been invoked
automatically:
--- System Configuration Dialog ---
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Would you like to enter the initial configuration dialog? [yes/no]:
The setup command facility prompts you for basic information about your router and network, and it
creates an initial configuration file.The prompts vary, depending on your router model, the installed
interface modules, and the software image. The following example and the user entries (in
bold
) are
shown as examples only.
For a description of the interface numbering, see the
“Interface Numbering” section on page 1-9
.
Note
If you make a mistake while using the setup command facility, you can exit and run the setup command
facility again. Press
Ctrl-C
, and enter
setup
at the privileged EXEC mode prompt (
Router#
).
Step 1
To proceed using the setup command facility, enter
yes
when the power-up messages have ended.
Would you like to enter the initial configuration dialog? [yes/no]:
yes
Step 2
When the following messages appear, press
Return
to enter basic management setup:
At any point you may enter a question mark '?' for help.
Use ctrl-c to abort configuration dialog at any prompt.
Default settings are in square brackets '[]'.
Basic management setup configures only enough connectivity
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]:
yes