Home » Cisco Manuals » Bridges & Routers » Cisco 2611XM » Manual Viewer

Cisco 2611XM Software Configuration Guide - Page 58

LAPB Encapsulation, 1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup

UPC - 746320661216

Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Configuring Interface Parameters Chapter 2 Using the Setup Command Facility Serial interface needs clock rate to be set in dce mode. The following clock rates are supported on the serial interface. 0 1200, 2400, 4800, 9600, 19200, 38400 56000, 64000, 72000, 125000, 148000, 500000 800000, 1000000, 1300000, 2000000, 4000000, 8000000 choose speed from above: [2000000]: 1200 Configure IP on this interface? [yes]: IP address for this interface: 2.0.0.1 Subnet mask for this interface [255.0.0.0]: Class A network is 2.0.0.0, 8 subnet bits; mask is /8 If IPX is configured on the router, the setup command facility prompts for the IPX map: Do you want to map a remote machine's IPX address to dlci? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed LAPB Encapsulation lapb circuit can be either in dce/dte mode Choose either from (dce/dte) [dte]: ATM-DXI Encapsulation Enter VPI number [1]: Enter VCI number [1]: Do you want to map the remote machine's IP address to vpi and vci's? [yes]: IP address for the remote interface: 6.0.0.1 Do you want to map the remote machine's IPX address to vpi and vci's? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed SMDS Encapsulation Enter smds address for the local interface: c141.5556.1415 We will need to map the remote smds station's address to the remote stations IP address Enter smds address for the remote interface: c141.5556.1414 Do you want to map the remote machine's smds address to IP address? [yes]: IP address for the remote interface: 2.0.0.1 Do you want to map the remote machine's smds address to IP address? [yes]: IPX address for the remote interface: 40.0060.34c6.90ed 1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup This section describes using setup command facility to configure a 1-port, 4-wire 56-kbps DSU/CSU WAN interface card. It discusses the following: • Choosing Circuit-Switched or Dedicated-Line Service • Switched Mode • Dedicated Mode 2-22 Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers OL-1957-03

Section	Page
Software Configuration Guide	1
Contents	3
Preface	11
Objectives	11
Audience	11
Organization	12
Document Conventions	12
Additional Information	13
Related and Referenced Documents	13
To Access Online User Documentation (PDF and HTML Formats):	14
Access User Documentation on the Documentation CD-ROM (HTML format only):	14
Obtaining Documentation	16
World Wide Web	16
Documentation CD-ROM	17
Ordering Documentation	17
Documentation Feedback	17
Obtaining Technical Assistance	17
Cisco.com	18
Technical Assistance Center	18
Contacting TAC by Using the Cisco TAC Website	18
Contacting TAC by Telephone	18
Understanding Interface Numbering and Cisco IOS Software Basics	21
Understanding Interface Numbering	21
Cisco 2600 Series Interface Numbering	21
WAN and LAN Interface Numbering	22
Voice Interface Numbering in Cisco 2600 Series Routers	24
Cisco 3600 Series Interface Numbering	24
Cisco 3600 Series Router Slot Numbering	24
Cisco 3600 Series Router Unit Numbering	28
Cisco 3600 Series Routers Voice Interface Numbering	29
Cisco 3700 Series Interface Numbering	29
Cisco 3725 Router Interface Numbering	29
Cisco 3725 Router Slot Numbering	30
Cisco 3745 Router Interface Numbering	31
Cisco 3745 Router Slot Numbering	31
Cisco 3700 Series Routers Voice Interface Numbering	33
Understanding Cisco IOS Software Basics	33
Getting Help	33
Understanding Command Modes	34
Undoing a Command or Feature	35
Saving Configuration Changes	35
Upgrading to a New Cisco IOS Release	35
Where to Go Next	35
Using the Setup Command Facility	37
Before Starting Your Router	37
Using the setup Command Facility	38
Configuring Global Parameters	38
Configuring Interface Parameters	42
Ethernet Interface Configuration	42
FastEthernet Interface Configuration	42
Token Ring Interface Configuration	43
Serial Interface Configuration	43
Frame Relay Encapsulation	44
LAPB Encapsulation	44
X.25 Encapsulation	45
ATM-DXI Encapsulation	45
SMDS Encapsulation	45
Serial Cisco IOS Commands Generated	45
Asynchronous/Synchronous Serial Interface Configuration	46
Synchronous Configuration	46
Frame Relay Encapsulation	46
LAPB Encapsulation	47
X.25 Encapsulation	47
ATM-DXI Encapsulation	47
SMDS Encapsulation	48
Asynchronous Configuration	48
ISDN BRI Interface Configuration	48
PPP Encapsulation	50
Frame Relay Encapsulation	50
LAPB Encapsulation	51
ATM-DXI Encapsulation	51
SMDS Encapsulation	51
X.25 Encapsulation	51
ISDN BRI Line Configuration	51
ISDNBRI Provisioning by Switch Type	52
Defining ISDN Service Profile Identifiers	53
E1/T1 ISDN PRI Configuration	54
E1/T1 PRI Mode	54
E1 Channelized Mode	54
PPP Encapsulation	55
Frame Relay Encapsulation	55
LAPB Encapsulation	56
ATM-DXI Encapsulation	56
SMDS Encapsulation	56
X.25 Encapsulation	56
T1 Channelized Mode	57
PPP Encapsulation	57
Frame Relay Encapsulation	57
LAPB Encapsulation	58
ATM-DXI Encapsulation	58
SMDS Encapsulation	58
1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup	58
Choosing Circuit-Switched or Dedicated-Line Service	59
Switched Mode	59
Dedicated Mode	59
Completing the Configuration	60
Where to Go Next	61
Configuring with the Command-Line Interface	63
Configuring the Host Name and Password	64
Verifying the Host Name and Password	65
Configuring 1-Port and 2-Port Ethernet Interfaces	65
Configuring Fast Ethernet Interfaces	66
Configuring Asynchronous/Synchronous Serial Network Modules or WAN Interface Cards	67
Configuring 16-Port and 32-Port Asynchronous Network Modules	71
Configuring ISDN BRI WAN Interface Cards	72
Configuring ISDN BRI Lines	74
ISDN BRI Provisioning by Switch Type	75
Defining ISDN Service Profile Identifiers	76
Configuring T1 and E1 Interfaces	77
Configuring T1 Interfaces	77
Configuring E1 Interfaces	78
Configuring TDM Connect (Data Pass-Through)	79
Configuring Codec Complexity	80
Configuring T1 (FT1) WAN Interface Cards	81
Default Configuration	81
Configuring ATM Interfaces	82
Configuring PVCs	83
Configuring SVCs	84
Configuring Inverse Multiplexing for ATM Interfaces	85
Configuring the ATM T1/E1 Interface	85
Configuring the IMA Interface	87
Checking the IMA Configuration	88
Configuring Analog Modem Interfaces	88
Checking the Modem Configuration	90
Configuring Wireless Multipoint Interfaces	91
Checking the Interface Configuration	91
Configuring 1-Port ADSL WAN Interface Card	91
Benefits	92
Restrictions	92
Prerequisites	93
Configuration Tasks	93
Configuring the ADSL Port on the ADSL WAN Interface Card	93
Verifying ATM Configuration	94
Configuration Examples	96
Configuring the NM-AIC-64, Contact Closure Network Module	96
Serial Communication Channels	97
Serial Data Channel	98
Asynchronous Craft Port	98
Configuring the AIC	98
Configuring a Discrete Alarm	98
Configuring an Analog Alarm as an Analog Monitoring Voltage	99
Configuring an Analog Alarm as a Discrete Monitoring Current	99
Configuring an Analog Alarm as a Discrete Monitoring Voltage	99
Configuring an Analog Alarm to Act Like a Discrete Alarm (Minimal Configuration Method)	99
Configuration Tasks	99
Configuring the AIC	100
Entering Alarm Configuration Mode and Configuring the AIC IP Address	100
Configuring the IP Route to the AIC	100
Accessing the AIC	102
Configuring the NOC IP Address	102
Configuring Alarms	103
Programming the Analog Contact Points	103
Programming the Discrete Contact Points	105
Verifying the IP Address	105
Troubleshooting Tips	107
Monitoring and Maintaining the NM-AIC-64 Contact Closure Network Module	107
Software Upgrade	107
Configuration Backup	108
Override	108
Configuration Examples	108
Configuring the 1-Port HSSI Network Module	108
Configuration Tasks	109
Specify a HSSI	109
Specify HSSI Encapsulation	109
Invoke ATM on a HSSI Line	110
Convert HSSI to Clock Master	110
Disable Fair Queueing	110
Configuration Examples	110
Configuring the Compression Network Module for the Cisco 3600 Series Routers	111
Configuration Task	111
Configuration Example	112
Configuring the Digital Modem Network Module for the Cisco 3640 Router	112
Prerequisites	113
Configuration Tasks	113
Configure the E1/T1 Network Module for ISDN PRI	114
Configure Channelized E1 ISDN PRI	114
Configure Channelized T1 ISDN PRI	115
Configure the ISDN D-Channel Serial Interfaces	115
Configure the ISDN D-Channel Serial Interface for E1 Modules	116
Configure the ISDN D-Channel Serial Interface for T1 Modules	116
Configure the Loopback Interface	117
Configure the LAN Interface	117
Create the Group Asynchronous Interface	117
Configure the ISDN Dialer Interface	118
Configure the Default IP Pool Information	119
Configure Modem Lines for Dial-In and Dial-Out	119
Configure the Modem for Dial-In	120
Configure the Modem for Dial-Out	120
Configuration Example	120
Configuring 1-Port G.SHDSL WAN Interface Card	120
Restrictions	122
Prerequisites	122
Configuration Tasks	122
Configuring G.SHDSL on a Cisco Router	122
Configuring ILMI on the DSLAM Connected to the ADSL WAN	124
Verifying ATM Configuration	124
Configuration Examples	126
Saving Configuration Changes	127
Where to Go Next	127
Configuring Voice-over-IP	129
Voice-over-IP Prerequisites	129
Configuring the Voice Interface	130
Voice-over-IP Configuration Examples	131
FXS-to-FXS Connection Using RSVP	132
Configuration for Router RLB-1	132
Configuration for Router RLB-w	133
Configuration for Router R12-e	133
Configuration for Router RLB-2	134
Linking PBX Users with E&M Trunk Lines	134
Router SJ Configuration	135
Router SLC Configuration	136
PSTN Gateway Access Using FXO Connection	136
Router SJ Configuration	137
Router SLC Configuration	137
PSTN Gateway Access Using FXO Connection (PLAR Mode)	138
Router SJ Configuration	138
Router SLC Configuration	139
Configuring Direct-Inward Dialing on a BRI Port	139
Router 1 Configuration	140
Router 2 Configuration	140
Router 3 Configuration	140
Where to Go Next	140
Configuration Examples	141
Cisco 2600 Series Router Configuration Example	141
Cisco 3631 Router Configuration Example	146
Cisco 3725 Router Configuration Example	150
1-Port ADSL WAN Interface Card Configuration Examples	151
VoATM over AAL2 on the ATM Interface Configuration Example	152
VoATM over AAL5 on the ATM Interface Configuration Example	154
NM-AIC-64, Contact Closure NetworkConfiguration Examples	156
AIC IP Address Configuration Example	156
IP Route to the AIC Configuration Examples	160
With an Unnumbered IP Address	160
Without an Unnumbered IP Address	161
AIC CLI Configuration for Alarms	162
Discrete Alarm	162
Analog Alarm Monitoring Current	162
Analog Alarm Monitoring Current Configured as a Discrete	162
Cisco 3640 Central Site Configuration to Support ISDN and Modem Calls	163
Configuration in CPE Mode Example	165
Configuration in CO Mode Example	167
Formatting the Compact Flash Memory Cards	171
Formatting Procedures for Compact Flash Memory Cards	171
Formatting Procedures	171
Determining the File System on a Compact Flash Memory Card	171
Formatting Compact Flash Memory as a Class B Flash File System	173
Formatting Compact Flash Memory as a Class C File System	174
File and Directory Operations	174
Operations for Use With Class B Flash File System	174
Operations for Use with Class C Flash File System	177
File Operations for Class C Flash File System	177
Directory Operations for Class C Flash File System	180
Using the ROM Monitor	183
Entering the ROM Monitor Mode	183
Configure	183
Verify	183
ROM Monitor Commands	184
ROM Monitor Syntax Conventions	184
Command Descriptions	185
Debugging Commands	187
Configuration Register Commands	187
Using the show rom-monitor command	188
Using the upgrade rom-monitor Command	189
Procedures for Recovering Boot and System Images	190
Using the xmodem Command	190
Using the tftpdnld Command	190

Match case Limit results 1 per page

2-22

Software Configuration Guide for Cisco 2600 Series, Cisco 3600 Series, and Cisco 3700 Series Routers

OL-1957-03

Chapter 2

Using the Setup Command Facility

Configuring Interface Parameters

Serial interface needs clock rate to be set in dce mode.

The following clock rates are supported on the serial interface.

1200, 2400, 4800, 9600, 19200, 38400

56000, 64000, 72000, 125000, 148000, 500000

800000, 1000000, 1300000, 2000000, 4000000, 8000000

choose speed from above: [2000000]: 1200

Configure IP on this interface? [yes]:

IP address for this interface: 2.0.0.1

Subnet mask for this interface [255.0.0.0]:

Class A network is 2.0.0.0, 8 subnet bits; mask is /8

If IPX is configured on the router, the

setup

command facility prompts for the IPX map:

Do you want to map a remote machine's IPX address to dlci? [yes]:

IPX address for the remote interface: 40.0060.34c6.90ed

LAPB Encapsulation

lapb circuit can be either in dce/dte mode

Choose either from (dce/dte) [dte]:

ATM-DXI Encapsulation

Enter VPI number [1]:

Enter VCI number [1]:

Do you want to map the remote machine's IP address to vpi and vci's? [yes]:

IP address for the remote interface: 6.0.0.1

Do you want to map the remote machine's IPX address to vpi and vci's? [yes]:

IPX address for the remote interface: 40.0060.34c6.90ed

SMDS Encapsulation

Enter smds address for the local interface: c141.5556.1415

We will need to map the remote smds station's address to the remote stations IP address

Enter smds address for the remote interface: c141.5556.1414

Do you want to map the remote machine's smds address to IP address? [yes]:

IP address for the remote interface: 2.0.0.1

Do you want to map the remote machine's smds address to IP address? [yes]:

IPX address for the remote interface: 40.0060.34c6.90ed

1-Port, 4-Wire 56-kbps DSU/CSU Configuration Setup

This section describes using

setup

command facility to configure a 1-port, 4-wire 56-kbps DSU/CSU

WAN interface card. It discusses the following:

•

Choosing Circuit-Switched or Dedicated-Line Service

•

Switched Mode

•

Dedicated Mode