Home » Cisco Manuals » Bridges & Routers » Cisco 2620XM » Manual Viewer

Cisco 2620XM Hardware Installation Guide - Page 85

Informational Commands in the ROM Monitor, flash, boot flash, boot slot0, boot c2600-i-mz 172.15.19.11 - flash memory slots

UPC - 746320671291

Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Appendix B Using the ROM Monitor ROM Monitor Command Descriptions • boot-Boots from the first Cisco IOS image in internal flash memory. • boot flash:-Boots from the first Cisco IOS image in the internal Flash memory. • boot flash: partition:-Boots from the first Cisco IOS image in the specified partition in internal flash memory. • boot flash: filename-Boots from the Cisco specified IOS image in internal flash memory. • boot flash: partition: filename-Boots from the specified Cisco IOS image in the specified partition in internal flash memory. • boot slot0:-(Cisco 2691 only) Boots from the first Cisco IOS image in the first partition in flash memory in slot 0. • boot slot0:2:-(Cisco 2691 only) Boots from the first Cisco IOS image in the second partition in compact flash memory in slot 0. • boot slot0: filename-(Cisco 2691 only) Boots from the specified Cisco IOS image in compact flash memory in slot 0. • boot slot1:3: filename-(Cisco 2691 only) Boots from the specified Cisco IOS image in the third partition in compact flash memory in slot 1. • boot filename tftpserver- Boots from the specified Cisco IOS image on the specified TFTP server (after first booting from flash). For example: boot c2600-i-mz 172.15.19.11 Note Use the CLI commands show version and show hardware to see the source of the currently running Cisco IOS image. Informational Commands in the ROM Monitor dev-(Cisco 2691 only) Lists boot device identifications on the router, for example: rommon 2 > dev Devices in device table: id name flash: internal compact flash slot0: external compact flash eprom: eprom rommon 3 > dir device:[partition:]-Lists the files on the named device. For example: rommon 8> dir flash: File size Checksum File name 2229799 bytes (0x220627) 0x469e C2600-j-m2.113-4T help-Shows a summary of ROM monitor commands (equivalent to ?). meminfo-Displays main memory size, starting address, and available range; size of packet memory; and size of NVRAM. The following example shows the meminfo command: rommon 9> meminfo Main memory size: 32 MB. Available main memory starts at 0xa000e000, size 32704KB IO (packet) memory size: 25 percent of main memory. NVRAM size: 32KB OL-2171-06 Cisco 2600 Series Routers Hardware Installation Guide B-5

Section	Page
Cisco 2600 Series Routers Hardware Installation Guide	1
Contents	3
Preface	7
Objectives	7
Audience	8
Organization	8
Conventions	8
Safety Warnings	9
Related Documentation	14
Cisco 90-Day Limited Hardware Warranty Terms	16
Obtaining Documentation	17
Cisco.com	17
Ordering Documentation	17
Documentation Feedback	17
Obtaining Technical Assistance	18
Cisco Technical Support Website	18
Submitting a Service Request	18
Definitions of Service Request Severity	19
Obtaining Additional Publications and Information	19
Overview of Cisco2600 Series Routers	21
Hardware Features	21
Reading the Front-Panel LEDs	23
Reading the Rear-Panel LEDs	25
Modules, Interface Cards, and Memory	28
Interface Numbering	29
WAN and LAN Interface Numbering	29
Voice Interface Numbering	31
System Specifications	31
Regulatory Compliance	32
Preparing to Install the Router	33
Safety Recommendations	33
Safety with Electricity	33
Preventing Electrostatic Discharge Damage	34
General Site Requirements	35
Power Supply Considerations	35
Site Environment	35
Site Configuration	36
Equipment Racks	36
Installation Checklist	36
Creating a Site Log	37
Inspecting the Router	38
Tools and Equipment for Installation and Maintenance	38
Console and Auxiliary Port Considerations	39
Console Port Connections	39
Auxiliary Port Connections	40
Preparing to Connect to a Network	40
Ethernet Connections	41
Token Ring Connections	41
Serial Connections	42
Configuring Serial Connections	42
Serial DTE or DCE Devices	42
Signaling Standards Supported	43
Distance Limitations	43
Asynchronous/Synchronous Serial Module Baud Rates	44
ISDN BRI Connections	44
56-K/Switched-56-kbps DSU/CSU Connections	45
Installing the Router	47
Installing Modules, Interface Cards, and Power Supplies	48
Setting Up the Chassis	49
Setting the Chassis on a Desktop	49
Mounting the Chassis in a Rack	50
Attaching the Brackets to Cisco261x, Cisco262x, Cisco26xxXM, and Cisco265x Series Routers	51
Attaching the Brackets to a Router of 2-RU Height	55
Installing the Router in a Rack	56
Mounting the Chassis on the Wall	57
Attaching Rubber Feet to the Router	57
Attaching Wall-Mount Brackets to the Router	57
Mounting the Router on the Wall	58
Installing the Chassis Ground Connection	59
Power Connections	61
Connecting Routers to AC Power	61
Connecting Routers to a DC-Input Power Supply	62
DC Wiring Requirements	62
Connecting Routers to the Cisco Redundant Power System	64
Connecting WAN, LAN, and Voice Cables	64
Ports and Cabling	64
LAN, WAN, and Voice Connection Procedures	65
Connecting to a Console Terminal or Modem	66
Connecting to the Console Port	66
Connecting to the Auxiliary Port	67
Identifying a Rollover Cable	68
Powering Up the Router	69
Checklist for Power Up	69
Front Panel Indicators	69
Power-Up Procedure	70
Configuring the Router	71
Initial Configuration Using SDM	72
Initial Configuration Using the Setup Command Facility	72
Initial Configuration Using the CLI (Manual Configuration)	74
Troubleshooting	77
Isolating Problems	77
Troubleshooting the Power and Cooling Systems	78
Environmental Reporting Features	78
Troubleshooting Modules, Cables, and Connections	79
System Messages	80
Recovering a Lost Password	80
Cisco Technical Assistance Center	80
Using the ROMMonitor	81
Entering ROM Monitor Mode	81
ROM Monitor Commands	82
ROM Monitor Command Syntax Conventions	83
ROM Monitor Command Descriptions	84
Router Management Commands	84
Boot Commands in the ROM Monitor	84
Informational Commands in the ROM Monitor	85
Other Useful ROM Monitor Commands	86
Debugging Commands	86
Configuration Register Commands	87
Recovering Cisco IOS Software Images	88
Copying an Image from the Console Using the xmodem Command	89
Description and Options of the xmodem Command	89
Console Requirements	89
Procedure for the xmodem Command	89
Copying an Image from a TFTP Server Using the tftpdnld Command	90
Restrictions on the tftpdnld Command	90
Procedure for the tftpdnld Command	91
Configuration Register	93
Configuration Register Settings	93
Changing Configuration Register Settings	94
Configuring the Boot Field	95
Enabling Booting from Flash Memory	97

Match case Limit results 1 per page

B-5

Cisco 2600 Series Routers Hardware Installation Guide

OL-2171-06

Appendix B

Using the ROM Monitor

ROM Monitor Command Descriptions

•

boot

—Boots from the first Cisco IOS image in internal flash memory.

•

boot

flash:

—Boots from the first Cisco IOS image in the internal Flash memory.

•

boot

flash:

partition

—Boots from the first Cisco IOS image in the specified partition in internal

flash memory.

•

boot

flash:

filename

—Boots from the Cisco specified IOS image in internal flash memory.

•

boot flash:

partition

filename

—Boots from the specified Cisco IOS image in the specified partition

in internal flash memory.

•

boot slot0:

—(Cisco 2691 only) Boots from the first Cisco IOS image in the first partition in flash

memory in slot 0.

•

boot slot0:2:

—(Cisco 2691 only) Boots from the first Cisco IOS image in the second partition in

compact flash memory in slot 0.

•

boot slot0:

filename

—(Cisco 2691 only) Boots from the specified Cisco IOS image in compact flash

memory in slot 0.

•

boot slot1:3:

filename

—(Cisco 2691 only) Boots from the specified Cisco IOS image in the third

partition in compact flash memory in slot 1.

•

boot

filename

tftpserver

—

Boots from the specified Cisco IOS image on the specified TFTP server

(after first booting from flash). For example:

boot c2600-i-mz 172.15.19.11

Note

Use the CLI commands

show version

and

show hardware

to see the source of the currently running

Cisco IOS image.

Informational Commands in the ROM Monitor

dev

—(Cisco 2691 only) Lists boot device identifications on the router, for example:

rommon 2 >

dev

Devices in device table:

name

flash:

internal compact flash

slot0:

external compact flash

eprom:

eprom

rommon 3 >

dir

device

[

partition

]—Lists the files on the named device. For example:

rommon 8>

dir flash

File size

Checksum

File name

2229799 bytes (0x220627)

0x469e

C2600-j-m2.113-4T

help

—Shows a summary of ROM monitor commands (equivalent to

meminfo

—Displays main memory size, starting address, and available range; size of packet memory;

and size of NVRAM. The following example shows the

meminfo

command:

rommon 9>

meminfo

Main memory size: 32 MB.

Available main memory starts at 0xa000e000, size 32704KB

IO (packet) memory size: 25 percent of main memory.

NVRAM size: 32KB