Home » Cisco Manuals » Wireless » Cisco 881W » Manual Viewer

Cisco 881W Hardware Installation Guide - Page 24

Back Panel of the Cisco C888SRST-W, Cisco IAD888EF, Cisco C888ESRST, and Cisco, - no antenna

UPC - 882658171802

Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Cisco 880 Series ISRs Chapter 1 Product Overview Figure 1-9 shows the back panel details of the Cisco 888SRST-W voice router. Figure 1-9 Back Panel of the Cisco C888SRST-W, Cisco IAD888EF, Cisco C888ESRST, and Cisco C888ESRST-W Voice RouterRouters 241905 2 1 2 6 3 4 578 9 10 1 Primary WAN port1-G.SHDSL, RJ-45 only 6 Antenna-captive wireless omnidirectional on the C888ESRST-W. Voice BRI on the dipole WLAN antenna (wireless models only) IAD888EF 2 Voice ports-four FXS2/DID3 ports and one 7 Reset button voice BRI 4port 3 4-port 10/100 Ethernet switch 8 Power connector 4 Serial port-console or auxiliary 9 Earth ground connection 5 PoE power connector-optional 10 Kensington security slot 1. Depending on the router model, the primary WAN port can be either G.SHDL or 10/100 FE. 2. FXS = Foreign Exchange Station. 3. DID = Direct Inward Dialing. 4. BRI = Basic Rate Interface. Caution The primary WAN port on all 888E models is designed for an RJ-45 connector only. Damage to the primary WAN port may occur if a non RJ-45 connector is inserted. 1-10 Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide OL-16193-03

Section	Page
Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series Integrated Services Routers Hardware Installation Guide	1
Preface	3
Objective	3
Audience	3
Organization	4
Conventions	4
Related Documentation	12
Searching Cisco Documents	12
Obtaining Documentation and Submitting a Service Request	12
1	15
Product Overview	15
General Description	15
Cisco 860 Series ISRs	16
Figure 1-1 Front Panel of the Cisco 860 Series Wireless ISR	16
Figure 1-2 Back Panel of the Cisco 861W ISR	17
Cisco 880 Series ISRs	17
Cisco 880 Series Data Routers	18
Figure 1-3 Front Panel of the Cisco 880 Series Wireless Data Router	18
Figure 1-4 Back Panel of the Cisco 888W Data Router	19
Figure 1-5 Back Panel of the Cisco 888E and Cisco 888E-W Data Router	20
Figure 1-6 Back Panel of the Cisco 888EG Data Router	21
Cisco 880 Series Voice Routers	21
Figure 1-7 Front Panel of the Cisco 880 Series Wireless Voice Router	22
Figure 1-8 Back Panel of the Cisco C881SRST-W Voice Router	23
Figure 1-9 Back Panel of the Cisco C888SRST-W, Cisco IAD888EF, Cisco C888ESRST, and Cisco C888ESRST-W Voice RouterRouters	24
Figure 1-10 Back Panel of the Cisco IAD888EB Router	25
Cisco 890 Series ISRs	25
Figure 1-11 Front Panel of the Cisco 890 Series Wireless ISR	26
Figure 1-12 Rear Panel of the Cisco 890 Series Wireless ISR	26
Figure 1-13 Back Panel of the Cisco 892-W Router	27
Hardware Features	27
Kensington Lock	28
Reset Button	28
LEDs	28
Table 1-1 LED Descriptions for the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs	28
Memory	31
Flash Memory	31
Main Memory	32
USB Port	32
Fan	32
Power over Ethernet Module	32
3G Cellular Data WAN Connectivity	33
Wireless LAN Connectivity	33
Table 1-2 Wireless Device Radios and Antennas	33
Supported Cisco Radio Antennas	34
Table 1-3 Cisco Antennas Supported on the Cisco 890 Series ISRs	34
Feature Summary	34
Table 1-4 Hardware Features Available in Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs	34
2	37
Installing the Router	37
Equipment, Tools, and Connections	37
Items Shipped with your Router	38
Table 2-1 Items and Their Quantities That Are Shipped with the Cisco 860 Series, Cisco 880 Series, and Cisco 890 Series ISRs	38
Additional Items	38
Connections	38
Ethernet Devices	39
Installing the Router	39
Warnings	39
Installing Antennas	40
Step 1 Manually screw the antennas tight to the RP-TNC connectors on the back of the router.	40
Figure 2-1 Attaching Antennas to the Router	40
Step 2 Orient the antennas. For optimum wireless performance, the antennas should be perpendicular with respect to the floor.	40
Figure 2-2 Antennas Oriented Vertically Up	41
Figure 2-3 Antennas Oriented Vertically Down	42
Installing on a Table	42
Mounting on a Wall	42
Step 1 Anchor the screws into the wall, leaving 1/8 inch (0.32 centimeter) between the screw head and the wall.	43
Figure 2-4 Wall-mount Holes on the Underside of the Router	43
Step 2 Hang the router on the screws, and place the power adapter on a nearby horizontal surface. See Figure 2-5.	43
Figure 2-5 Router Mounted on the Wall	44
Step 3 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-10.	44
Installing in a Rack	45
Step 1 Remove the screws shown in Figure 2-6.	45
Figure 2-6 Screw Location	45
Step 2 Using the screws provided, attach the rack-mount brackets to the Cisco 890 series ISR chassis as shown in Figure 2-7. Use two screws on each side. Use a number 2 Phillips screwdriver to install the bracket screws on both sides of the chassis.	45
Figure 2-7 Attaching the Rack-mount Brackets to the Cisco 890 Series ISR	45
Step 3 Using two screws for each side (supplied with the rack), attach the Cisco 890 series ISR with rack-mount brackets to a 19...	46
Step 4 Place the power adapter on a nearby horizontal surface.	46
Step 5 Connect the chassis to a reliable earth ground. For the chassis ground connection procedures, see the “Installing the Router Ground Connection” section on page 2-10.	46
Installing the Router Ground Connection	46
Step 1 Strip one end of the ground wire to the length required for the ground lug or terminal.	46
Step 2 Crimp the ground wire to the ground lug or ring terminal, using the wire crimper.	46
Step 3 Attach the ground lug or ring terminal to the chassis as shown in Figure 2-8. For a ground lug, use the two provided scre...	46
Figure 2-8 Chassis Ground Connection Using Ring Terminal	47
Step 4 Connect the other end of the ground wire to a known reliable earth ground point at your site.	47
3	49
Connecting the Router	49
Preparing to Connect the Router	50
Preventing Damage to the Router	50
Connecting a PC, Server, or Workstation	51
Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-1 shows a Cisco 888W router connected to a PC.	51
Figure 3-1 Connecting a Server, PC, or Workstation	51
Step 2 Connect the other end of the cable to the RJ-45 port on the network interface card (NIC) that is installed in the PC, server, or workstation.	51
Step 3 (Optional) Connect additional servers, PCs, or workstations to the other Ethernet switch ports.	51
Connecting a Phone	52
Step 1 Connect one end of the yellow Ethernet cable to Ethernet switch port 0 or port 1 on the router. Figure 3-2 shows a Cisco 888W router connected to a phone.	52
Figure 3-2 Connecting a Phone	52
Step 2 Connect the other end of the cable to the RJ-45 port on the phone.	52
Connecting an External Ethernet Switch	53
Step 1 Connect one end of the yellow Ethernet cable to an Ethernet switch port on the router. Figure 3-3 shows a Cisco 888W router connected to an Ethernet switch.	53
Figure 3-3 Connecting to an Ethernet Switch	53
Step 2 Connect the other end of the cable to the available port on the Ethernet switch to add additional Ethernet connections.	53
Step 3 Turn on the Ethernet switch.	53
Connecting the V.92 modem Port	54
Figure 3-4 Connecting to Your Service Provider Through the V.92 port	54
Step 1 Connect one end of the straight-through R-J11 cable to the V.92 port.	54
Step 2 Connect the other end of the straight through R-J11 cable to an RJ-11 telephone wall outlet.	54
Connecting a Terminal or PC to the Console Port	55
Step 1 Connect the RJ-45 end of a DB-9-to-RJ-45 serial cable to the RJ-45 Console Aux port on the router. Figure 3-5 shows the RJ-45 end of the serial cable connected to the Console Aux port on the router.	55
Figure 3-5 Connecting a Terminal or PC to the Console Port	55
Step 2 Connect the DB-9 end of the DB-9-to-RJ-45 serial cable to the to the COM port on your laptop or PC.	55
Step 3 To communicate with the router, start a terminal emulator application.	55
Terminal Emulator Settings	55
Connecting a Modem to the Auxiliary Port	56
Step 1 Connect the RJ-45 end of the adapter cable to the Aux port on the router as shown in Figure 3-6.	56
Figure 3-6 Connecting a Modem to the Aux Port	56
Step 2 Connect the DB-9 end of the console cable to the DB-9 end of the modem adapter.	56
Step 3 Connect the DB-25 end of the modem adapter to the modem.	56
Step 4 Make sure that your modem and the router auxiliary port are configured for the same transmission speed (up to 115200 bits per second [b/s] is supported) and support mode control with data carrier detect (DCD) and data terminal ready (DTR).	57
Connecting the 3G Card	57
Step 1 Align the 3G card to the 3G express card slot, as shown in Figure 3-7. Keep the card parallel to the surface and firmly push the card into the slot.	57
Figure 3-7 Inserting the 3G Card	58
Step 2 Open the top of the anti-theft locking bracket, as shown in Figure 3-8.	58
Figure 3-8 Opening the Anti-theft Locking Bracket	58
Step 3 Slide the opened locking bracket under the 3G card. The locking bracket should align with the notches on either side of t...	59
Figure 3-9 Installing the Locking Bracket	59
Step 4 Close the locking bracket, as shown in Figure 3-10.	60
Figure 3-10 Closing the Locking Bracket	60
Step 5 Insert the screws, as shown in Figure 3-11, and tighten with a number 2 Phillips screwdriver.	60
Figure 3-11 Inserting the Screws	60
Step 6 To connect the antenna to the 3G card, insert the antenna connector into the antenna connector hole on the 3G card. Figure 3-12 show the antenna connected to the 3G card.	60
Figure 3-12 Antenna connected to the 3G Card	61
Step 7 Clean the flat surface to which you will affix the antenna.	61
Step 8 Remove the protective tape from the adhesive on the bottom of the antenna cradle, then firmly press the cradle to the flat surface.	61
Connecting a Data BRI Port	61
Step 1 Connect one end of the orange ISDN S/T cable to the Data BRI port on the router. Figure 3-13 shows a Data BRI connection.	62
Figure 3-13 Connecting the Data BRI Port to the ISDN Line	62
Step 2 Connect the other end of the orange ISDN S/T cable to the S/T port on the NT1 box.	62
Step 3 Connect the first unshielded CAT 5 cable from the U-port on the NT1 box to the telephone line port on the splitter.	62
Step 4 Connect the second unshielded Category 5 cable from the telecommunication service port on the splitter to the wall jack to allow a link to the network service provider.	62
Connecting an FE Line to an FE WAN Port	63
Step 1 Connect one end of the yellow cable to the FE WAN port as shown in Figure 3-14.	63
Figure 3-14 Connecting the FE WAN Port	63
Step 2 Connect the other end of cable to an available port on the modem.	63
Connecting an GE Line to an GE WAN Port	64
Step 1 Connect one end of the yellow cable to the GE WAN port as shown in Figure 3-14.	64
Figure 3-15 Connecting the GE WAN Port	64
Step 2 Connect the other end of cable to an available port on the modem.	64
Connecting an xDSL Line	65
Step 1 Connect one end of an RJ-11 (RJ-45 on 880 E models) cable to the port on the router. See Figure 3-16.	65
Figure 3-16 Connecting the xDSL Line	65
Step 2 Connect the other end of the cable to the DSL wall jack.	65
Connecting Power over Ethernet	66
Figure 3-17 Connecting PoE	66
Connecting the AC Adapter	66
Step 1 Connect the router to an AC power outlet as shown in Figure 3-18.	67
Figure 3-18 Connecting the AC Adapter	67
Step 2 To secure the power cord to the router, attach the power lock clip to the power cord, and slide the clip to the end of the DC plug. See Figure 3-19.	68
Figure 3-19 Securing the Power Cord	68
Step 3 Snap the latches into the holes on either side of the power connector. See Figure 3-20.	69
Figure 3-20 Power Lock Clip Latched Into the Holes on Either Side of the Power Connector	69
Connecting an FXS Line	69
Step 1 Connect one end of the straight-through RJ-11 cable to the FXS port. Figure 3-21 shows an FXS line connection.	70
Figure 3-21 Connecting an FXS Line	70
Step 2 Connect the other end of the cable to the RJ-11 port on the fax or telephone machine.	70
Connecting an FXO Line	71
Step 1 Connect one end of the straight-through RJ-11 cable to the FXO port. See Figure 3-22.	71
Figure 3-22 Connecting an FXO Line	71
Step 2 Connect the other end of the RJ-11 cable to a telephone wall outlet.	71
Connecting a Voice ISDN BRI Line	72
Step 1 Connect one end of a straight-through RJ-45-to-RJ-45 cable to the Voice BRI port.	72
Figure 3-23 Connecting a Voice BRI Line	73
Step 2 Connect the other end of the cable to the RJ-45 telephone outlet or other device.	73
Verifying Connections	74
Table 3-1 Verifying the Router Operation	74
4	77
Initial Configuration	77
Cisco Configuration Professional Express	77
Cisco IOS CLI	77
Step 1 Set up a console connection to your router. The following message is displayed:	78
Step 2 Press Return or Enter. The following message is displayed:	78
Step 3 Enter the username username1, and press Return or Enter. The following prompt is displayed:	78
Step 4 Enter the password password1, and press Return or Enter. The following prompt is displayed:	78
Step 5 To change the username and password, enter the following at the prompt:	78
Step 6 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5.	79
Setup Command Facility	79
Step 1 Set up a console connection to your router, and enter privileged EXEC mode. For instructions on how to enter privileged EXEC mode, see Step 1 through Step 4 in the “Cisco IOS CLI” section on page 4-1.	79
Step 2 In privileged EXEC mode, at the prompt, enter setup.	79
Step 3 To proceed using the setup command facility, enter yes:	79
Step 4 When the following messages appear, enter yes to enter basic management setup:	79
Step 5 Enter a hostname for the router (this example uses Router):	80
Step 6 Enter an enable secret password. This password is encrypted (more secure) and cannot be seen when viewing the configuration.	80
Step 7 Enter an enable password that is different from the enable secret password. This password is not encrypted (less secure) and can be seen when viewing the configuration.	80
Step 8 Enter the virtual terminal password, which prevents unauthenticated access to the router through ports other than the console port:	80
Step 9 Respond to the following prompts as appropriate for your network:	80
Step 10 Choose one of the available interfaces for connecting the router to the management network:	80
Step 11 Respond to the following prompts as appropriate for your network:	80
Step 12 Respond to the following prompts. Enter 2 to save the initial configuration.	81
Step 13 Verify the initial configuration. See the “Verifying the Initial Configuration” section on page 4-5 for verification procedures.	81
Verifying the Initial Configuration	81
Initial Configuration of the Wireless Access Point	81
A	83
Technical Specifications	83
Router Specifications	84
Table A-1 Router Specifications	84
Wireless Access Point	85
Table A-2 Wireless Access Point Specifications	85
FE and GE Port Pinouts	85
Table A-3 Ethernet LAN Port Pinouts	85
Console and Auxiliary Port Connector Pinouts	86
Table A-4 Console and Auxiliary Port Connector Pinouts	86
FXS and FXO Port Connector Pinouts	86
Table A-5 FXS and FXO Connector Pinouts (RJ-11-to-RJ-45)	86
VDSL2 Port Connector Pinouts	86
Table A-6 VDSL2 Connector Pinouts (RJ-11-to-RJ-45)	86
ADSL2+ Port Connector Pinouts	87
Table A-7 ADSL2+ Connector Pinouts (RJ-11)	87
V.92 Port Connector Pinouts	87
Table A-8 V.92 Connector Pinouts (RJ-11-to-RJ-45)	87
G.SHDSL Port Connector Pinouts	88
Table A-9 G.SHDSL WAN Port Pinouts	88
Data BRI Port Connector Pinouts	88
Table A-10 Data BRI Port Pinouts	88
Voice ISDN BRI Interface Pin Numbers and Functions	88
Table A-11 Interface Pin Numbers and Functions	88
Cable Specifications	89
Ethernet Cable Specifications	89
Table A-12 Ethernet Cable Specifications	89