Cisco AIR-ANT1949 User Guide
Cisco AIR-ANT1949 Manual
 |
View all Cisco AIR-ANT1949 manuals
Add to My Manuals
Save this manual to your list of manuals |
Cisco AIR-ANT1949 manual content summary:
- Cisco AIR-ANT1949 | User Guide - Page 1
Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) Overview This document describes the 13.5-dBi Yagi mast mount antenna and provides instructions for mounting it. The antenna operates in the 2.4- to 2.5-GHz frequency range and is designed for point-to-point communications. The antenna is - Cisco AIR-ANT1949 | User Guide - Page 2
81012 System Requirements This antenna is designed for use with Cisco Aironet access points and bridges but can be used with any 2.4-GHz Cisco Aironet radio device that uses a reverse-polarity threaded naval connector (RP-TNC). Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) 2 78 - Cisco AIR-ANT1949 | User Guide - Page 3
, mast, cable, and metal guy wires are all excellent conductors of electrical current. Even the slightest touch of any of these parts to a power line complete an electrical path through the antenna and the installer: you! 78-14720-02 Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949 - Cisco AIR-ANT1949 | User Guide - Page 4
. 3. Mount the antenna discharge unit as closely as possible to where the lead-in wire enters the building. 4. Drill a hole in the building's wall as closely as possible to the equipment to which you will connect the lead-in cable. Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) 4 78 - Cisco AIR-ANT1949 | User Guide - Page 5
with the antenna. To install the antenna on a mast, you need the following tools and equipment. • A 7/16-in. (11.1 mm) wrench • Cable ties or electrical tape • Coaxial cable weatherproofing material (such as CoaxSeal) 78-14720-02 Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) 5 - Cisco AIR-ANT1949 | User Guide - Page 6
plate Mast mount - top view Place flat washers between bolt heads (or nuts) and mounting base in all mounting configurations. Intermediate plate required for mounting on rough surfaces. Direction of maximum signal Wall mount Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) 6 81013 - Cisco AIR-ANT1949 | User Guide - Page 7
antenna terminates with a RP-TNC plug after a short, 3-ft (0.91-m) cable. The mating connector to the antenna is an appropriate RP-TNC jack. The connector on the opposite end will vary according to the type of equipment used. 78-14720-02 Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949 - Cisco AIR-ANT1949 | User Guide - Page 8
at www.cisco.com/go/trademarks. Third party trademarks mentioned are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (1005R) Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna (AIR-ANT1949) 8 78-14720
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
 |
 |
Corporate Headquarters:
© 2006 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706
USA
Cisco Aironet 13.5-dBi Yagi Mast Mount Antenna
(AIR-ANT1949)
Overview
This document describes the 13.5-dBi Yagi mast mount antenna and provides instructions for mounting
it. The antenna operates in the 2.4- to 2.5-GHz frequency range and is designed for point-to-point
communications. The antenna is a completely enclosed 16-element, vertically polarized directional Yagi
and is designed to be mounted outdoors on a mast. The antenna can also be used indoors and can be
mounted on a flat vertical surface, such as a wall.
The following information is provided in this document.
•
Technical Specifications, page 2
•
System Requirements, page 2
•
Installation Notes, page 4
•
Choosing a Mounting Location, page 5
•
Tools and Equipment Required, page 5
•
Mounting the Antenna, page 6
•
Obtaining Documentation and Submitting a Service Request, page 8