Cisco ASR1006-10G-SHA/K9 Installation Guide - Page 17

Chapter 6 Cisco ASR 1006 Router Overview and Installation Installing the Cisco ASR 1006 Router in a Rack Figure 6-11 shows the router installed on a four-post rack. Figure 6-11 Installing the Cisco ASR 1006 Router in a Four-Post Equipment Rack 1 A/L C/A A/L C/A A/L C/A 0 3 A/L C/A 1 2 A/L C/A A/L C/A 0 1 A/L C/A A/L C/A 0 1 11 A/L C/A A/L C/A 0 1 A/L C/A A/L C/A 0 1 00 A/L C/A A/L C/A 0 1 PWR ACTV F1 STAT STBY ASR1000-ESP10 F0 PWR ACTV STAT STBY ASR1000-ESP10 RR11 PWR ACTV STAT STBY ASR1000-RP1 CRIT MAJ MIN RR00 PWR ACTV STAT STBY ASR1000-RP1 CRIT MAJ MIN ACO ACO HD USB 0 BF 1 DISK HD USB 0 BF 1 DISK 2 2 2 2 2 2 A/L C/A A/L C/A A/L C/A A/L C/A A/L C/A 3 A/L C/A 3 A/L C/A 3 A/L C/A 3 A/L C/A 3 A/L C/A A/L C/A 0 1 A/L C/A 0 1 A/L C/A SPA-4XOC3-POS SPA-4XOC3-POS SPA-4XOC3-POS SPA-4XOC3-POS SPA-4XOC3-POS SPA-4XOC3-POS STATUS STATUS STATUS STATUS STATUS STATUS ASR1000-SIP10 PWR STATUS ASR1000-SIP10 PWR STATUS ASR1000-SIP10 PWR STATUS 0 1 A/L C/A 0 1 A/L C/A 0 1 A/L C/A 0 1 CARRIER LINK BITS MGMT ETHERNET CARRIER LINK BITS MGMT ETHERNET CON AUX CON AUX A/L C/A A/L C/A A/L C/A A/L C/A A/L C/A A/L C/A 2 2 2 2 2 2 A/L C/A A/L C/A A/L C/A A/L C/A A/L C/A A/L C/A 3 A/L C/A 3 A/L C/A 3 A/L C/A 3 A/L C/A 3 A/L C/A 3 A/L C/A Cisco ASR 1006 SPA-4XOC3-POS STATUS STATUS SPA-4XOC3-POS 2 STATUS SPA-4XOC3-POS STATUS SPA-4XOC3-POS 1 STATUS SPA-4XOC3-POS SPA-4XOC3-POS STATUS 0 F1 F0 R1 R0 4 3 280084 2 1 Four-post equipment rack rear rail 2 Cisco ASR 1006 rear rack-mount brackets 3 Cisco ASR 1006 front rack-mount brackets 4 Four-post equipment rack front rail When handling the chassis, always follow proper lifting practices. See the "Chassis-Lifting Guidelines" section on page 5-23. Note Inner clearance (the width between the inner sides of the two posts or rails) must be at least 19 inches (48.26cm). The height of the chassis is 10.45 inches (26.543 cm). Airflow through the chassis is from front to back. Note Make sure the rack is stabilized. Step 1 (Optional) Install a shelf in the rack to support the Cisco ASR 1006 Router. If you are using a shelf then raise the chassis to the level of the shelf. Let the bottom of the chassis rest on the brackets, but continue to support the chassis.Using two people, lift the chassis into the rack using the side handles and grasping underneath the power supply bays. OL-13208-09 Cisco ASR 1000 Series Aggregation Services Routers Hardware Installation Guide 6-17