Cisco SG100D-08 Hardware Installation Guide - Page 59

Redirection After BIOS POST, Serial Port Mode

Get Cisco SG100D-08 PDF manuals and user guides View all Cisco SG100D-08 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 4 Installing the Internet Streamer CDS Software and Initially Configuring a CDE Figure 4-8 Configure Super I/O Chipset Screen Running the BIOS Setup Utility Step 13 Set the Serial Port2 Address option to Disabled. Press Esc to return to the Advanced menu. Choose Remote Access Configuration and press Enter. The Configure Remote Access Type and Parameters screen appears (see Figure 4-9). Figure 4-9 Configure Remote Access Type and Parameters Screen Step 14 a. Set the Serial port number option to COM 1. b. Set the Serial Port Mode option to 9600 8, n, 1. c. Set the Redirection After BIOS POST option to Disabled. When you are finished, navigate to the Exit submenu and choose Save and Exit. Press OK when prompted (see Figure 4-10). OL-13478-03 Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide 4-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
4-7
Cisco Content Delivery Engine 100/200/300/400 Hardware Installation Guide
OL-13478-03
Chapter 4
Installing the Internet Streamer CDS Software and Initially Configuring a CDE
Running the BIOS Setup Utility
Figure 4-8
Configure Super I/O Chipset Screen
Set the
Serial Port2 Address
option
to
Disabled
.
Step 13
Press
Esc
to return to the Advanced menu. Choose
Remote Access Configuration
and press
Enter
. The
Configure Remote Access Type and Parameters screen appears (see
Figure 4-9
).
Figure 4-9
Configure Remote Access Type and Parameters Screen
a.
Set the
Serial port number
option to
COM 1
.
b.
Set the
Serial Port Mode
option to
9600 8, n, 1
.
c.
Set the
Redirection After BIOS POST
option to
Disabled
.
Step 14
When you are finished, navigate to the
Exit
submenu and choose
Save and Exit
. Press
OK
when
prompted (see
Figure 4-10
).