Clifford Cyber 4 Owners Guide - Page 9

If you wish to reset all the user-selectable features to their normal factory presets, you can do so simply by choosing the Reset all featuresselection (column 1, row 7) on the Table of User-Selectable Features. If you do so, all features - except the programmed remote controls and your valet code - will be reset to the factory settings that are indicated in BOLD type on the Table of User-Selectable Features. To reset all remote controls, use the Clear all remotes feature in column 2, row 6. To reset your valet code, use the Set a new secret valet code feature in column 2, row 7. Table of User-Selectable Features Feature Select 1 blank press 2 blank presses 3 blank presses 4 blank presses 1 D press Add a new remote control NOTE 1 Chirps: off/on (1/2 chirps) AutoArming: off/on NOTE 5 - Other vehicle's remote: arm/disarm (1 then 2 chirps) 2 D presses Personalized Siren Sounds* NOTE 2 NOT USED Lock upon AutoArming:off/on NOTE 6 - Other vehicle's remote: trunk release* (2 chirps) 3 D presses Play Personalized Siren Sounds*: Remote valet mode via trigger only/always (1/2 chirps) button combo + D: off/on AutoArming entry delay: off/on NOTE 6 - Other vehicle's remote: silent arm and disarm (3 chirps) 4 D presses Siren duration: 30 /60/90sec. (1/2/3 chirps) AutoStart*: both off/both on/temp only/battery only (1/2/3/4 chirps) FACT: off/on NOTE 6 - Other vehicle's remote: remote engine starting* (4 chirps) 5 D presses AutoLock: off/on NOT USED NOT USED NOTE 6 - Other vehicle's remote: timed headlight activation* (5 chirps) 6 D presses AutoUnLock: off/on Clear all remotes NOTE 3 NOT USED NOTE 6 - Other vehicle's remote: window rolldown/venting* (6 chirps) 7 D presses Reset all features (except remotes and valet code) to factory settings Set a new secret valet code NOTE 4 NOT USED NOTE 6 - Other vehicle's remote: remote valet mode (7 chirps) * Re quires op tional wir ing or ac ces sory; ask your Clif ford Dealer for de tails. NOTE 1: Press the button of the new remote. You'll hear one chirp. Press the chirps to confirm that the new remote control has been added. button again. You'll hear two NOTE 2: This feature requires the optional Self-Powered SmartSiren 4. If so equipped, selection of this feature will cause the system to sound a few seconds of siren sound #1. Press the blank button to turn on this sound or the D button to turn it off. It will then sound a few seconds of sound #2. Repeat: blank=ON, D=OFF for each of the six sounds. NOTE 3: You'll hear two chirps to indicate all remotes have been cleared from memory. You must now add new/existing remotes with the "Add new remote control" feature and/or the "Other vehicle's remote" feature. NOTE 4: Immediately PRESS THE BLANK BUTTON, THEN enter your new code, wait for the two chirps, then turn off the ignition (you'll hear 3 chirps to confirm program mode exit). You MUST now turn the ignition back on and then re-enter your new code. If the LED flashes on, your new code has been accepted. If the LED does not light, the two codes did not match and the system has reverted to your previous code. NOTE 5: Lets you arm/disarm with the remote control of a G4 system on your other vehicle(s). For instance, to set theD button of the other car's remote to arm and disarm this system, select column 4, row 1, then press the D button of the other car's remote (you'll hear one chirp). Immediately press the D button again (you will hear a 2-chirp confirmation). The D button of the other vehicle's remote will now arm/disarm this system. NOTE 6: The features in this column allow you to control your system with the remote control of a G4 system on your other vehicle(s). Just select the function you wish, then press the unused button or button combination on the other remote that you want to use to perform that function on this system (you will then hear a the chirps noted). NOTE: You must first set a button or button combination on the other car's remote that will arm/disarm the system (column 4, row 1) before these others will be accepted. Lifetime limited factory warranty terms & conditions Cliffordvehiclesecuritysystemsandaccessoriesrequireprofessionalinstallation by an Authorized Clif ford Dealer. Un less the sys tem is sold and in stalled by an Authorized Clifford Dealer, all product warranties and guarantees are void. As the manufacturer, Clifford Electronics warrants to the original consumer pur chaser, the sys tem con trol unit and re mote con trols to be free from de fects in ma te rial and work man ship for as long as you own the ve hi cle in which the systemwasoriginallyinstalled.Allotherpartsofthesystemandaccessoriestothesystem are war ranted to be free from de fects in ma te rial and work man ship for one (1) year from the date of purchase. Clifford Electronics will repair or replace, at its option and free of charge during the warranty period, any system com po nent that proves de fec tive in ma te rial or work man ship un der nor mal in stal la tion, use, and serv ice, pro vided the prod uct is re turned to our fac tory by an AuthorizedCliffordDealer,transportation charges pre paid. Prod ucts re turned to our fac tory must be ac com pa nied by a pho to copy of the pur chase re ceipt. In the ab sence of such pur chase re ceipt, the war ranty pe riod shall be one (1) year from the date of manu fac ture. Any dam age to the prod uct(s) as a re sult of mis use, abuse, ne glect, ac ci dent, in cor rect wir ing, im proper in stal la tion, de struc tion or al tera tion of the se rial number, re pair or al tera tion out side our fac tory, or any use violative of instructions furnished by us will void the warranty. This warranty is limited to defective parts and specifically excludes any incidental or con se quen tial dam ages con nected there with. This warranty is not transferable. Clif ford Elec tron ics makes no war ranty against theft. This war ranty is not to be construed as an insurance policy against loss. Warranty on installation labor, removal and reinstallation charges are not the responsibility of Clifford Electronics, Inc. 9