Clifford SuperNova 2 Owners Guide - Page 18

User-selectable features, Programming table for user-selectable features

Page 18 highlights

User-selectable features Your SuperNova II allows you to set many of its features to your own personal preferences. We have made the programming procedures very simple: to make a change, you just press the PlainView switch a few times. The system comes from the factory with all of its features pre-programmed as noted in the table below and on the next page. To change any of the settings, use the following procedure. To restore the feature to its factory setting, just repeat the procedure: 1. Select the feature you wish to program from the table below and on the following page. Note the number of momentary (spring-loaded) presses. 2. Turn your vehicle's ignition switch to its "ON" position. 3. Enter your valet code (see page 11) on the PlainView switch. 4. When the LED turns on, immediately press and release the momentary side of the switch the number of times indicated in the third column of the programming table for the feature you selected (to help you count, you will hear a single chirp confirmation each time you press the momentary side). a. If noted, perform the "Secondary action." 5. Wait 3 seconds. You will hear 1-4 chirps (as noted in the "Program completion confirmation" column) and the LED will turn off. Turn the ignition off. 6. Repeat steps 1-5 for any other features you wish to program. Programming table for user-selectable features Feature Factory setting # of momentary presses Secondary action Program completion confirmation Result AutoArming ON 4 - 1 chirp = OFF Change state from 2 chirps = ON ON to OFF or vice-versa AutoArm & Lock OFF 5 - 1 chirp = OFF Change state from 2 chirps = ON OFF to ON or vice-versa FACT ON 6 - 1 chirp = OFF Change state from 2 chirps = ON ON to OFF or vice-versa AutoLock ON 7 - 1 chirp = OFF Change state from 2 chirps = ON ON to OFF or vice-versa AutoUnLock ON 8 - 1 chirp = OFF Change state from 2 chirps = ON ON to OFF or vice-versa Chirp confirmation ON 9 - 1 chirp = OFF Change state from 2 chirps = ON ON to OFF or vice-versa Siren duration 30 sec. 10 - 1 chirp=60sec Change duration from 30 to 2 chirps=30sec 60 seconds or vice-versa Add a new remote to channel 1 - (arm/disarm) 11 Press remote control button 1 1 chirp Button 1/channel 1 code of the new remote control has been memorized continued . . . 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

User-selectable features
Your SuperNova II allows you to set many of its features to your own personal
preferences. We have made the programming procedures very simple: to make a
change, you just press the PlainView switch a few times. The system comes from
the factory with all of its features pre-programmed as noted in the table below and
on the next page. To change any of the settings, use the following procedure. To
restore the feature to its factory setting, just repeat the procedure:
1.
Select the feature you wish to program from the table below and on the following
page. Note the number of momentary (spring-loaded) presses.
2.
Turn your vehicle’s ignition switch to its “ON” position.
3.
Enter your valet code (see page 11) on the PlainView switch.
4.
When the LED turns on, immediately press and release the momentary side of
the switch the number of times indicated in the third column of the programming
table for the feature you selected (to help you count, you will hear a single chirp
confirmation each time you press the momentary side).
a.
If noted, perform the “Secondary action.”
5.
Wait 3 seconds. You will hear 1-4 chirps (as noted in the “Program completion
confirmation” column) and the LED will turn off. Turn the ignition off.
6.
Repeat steps 1-5 for any other features you wish to program.
Programming table for user-selectable features
continued . . .
Feature
Factory
setting
# of
momentary
presses
Secondary
action
Program
completion
confirmation
Result
AutoArming
ON
4
1 chirp = OFF
2 chirps = ON
Change state from
ON to OFF or vice-versa
AutoArm
& Lock
OFF
5
1 chirp = OFF
2 chirps = ON
Change state from
OFF to ON or vice-versa
FACT
ON
6
1 chirp = OFF
2 chirps = ON
Change state from
ON to OFF or vice-versa
AutoLock
ON
7
1 chirp = OFF
2 chirps = ON
Change state from
ON to OFF or vice-versa
AutoUnLock
ON
8
1 chirp = OFF
2 chirps = ON
Change state from
ON to OFF or vice-versa
Chirp
confirmation
ON
9
1 chirp = OFF
2 chirps = ON
Change state from
ON to OFF or vice-versa
Siren
duration
30 sec.
10
1 chirp=60sec
2 chirps=30sec
Change duration from 30 to
60 seconds or vice-versa
Add a new
remote to
channel 1
(arm/disarm)
11
Press remote control button
1
1 chirp
Button 1/channel 1 code
of the new remote control
has been memorized
17