Cobra MR HH450 MR HH450 DUAL Manual - English - Page 15

VOHpFerMatainrigneYoRuardRioaPdirootocols Intro Operation Speaker/Mic Port Secondary Icons Installation Talk Button Notice Backlight/Key Lock Button Key Locked Buttons U VOX ROG GMRS VHF TRX HI SAME MEM Key Lock Icon 24 English Getting Started Radio Customer Assistance SpeWaakrraentyr and Microphone The internal Radio Speaker and Microphone are located on the bottom front face of the radio below the lower control buttons. An optional Speaker/Microphone port is located at the top oCAfsutsshitsotemanercrae dio between the antenna and the Power/Volume control. Unthread the Speaker/Microphone port cover to access and install an optional Cobra speaker or microphone into this port. Talk Button Press and hold the Talk button to transmit messages. Release thCeauTtioanlk buttoWnarntiong stop transmitting. Backlight/Key Lock Button To Display the Backlight Momentarily: Press the Backlight/Key Lock button. The backlight will remain On for 10 seconds. If the backlight is already On, another press of the Backlight/Key Lock button will turn it Off. Key Lock To prevent accidental changes to your settings, you can lock all of the following buttons: n Channel Up Button n Channel Down Button n Band Button n REWIND Button n SCAN Button n MEM/ESC Button n WX/H-M-L Button n 16/9 Button n TRI-WATCH Button n Call/Enter/Setup Button To Lock or Unlock the Buttons: Press and hold the Backlight/Key Lock button for two (2) seconds. The Key Lock icon will appear or disappear ROG GMRS in the LCD. When Key Lock is On, pressing any of the listed buttons on the front of the radio will result in a three VHF (3) beep error message. Both the Backlight/Key Lock button and the Talk button are active - you can Receive (Rx) or Transmit (Tx) a message with Key Lock On, but you cannot change the TRX channel. ROG GMRS VHF TRX U VOHpFerMatainrigneYoRuardRioaPdirootocols Getting Started VOX Intro HI SAOMpEeraMtionEM Channel Customer Assistance UWparr/aDntyown Buttons MR HH350/450/500 Channel Up/Down Buttons Your radio will Receive (Rx) and Transmit (Tx) VHF/GMRS signals on the channel indicated on the LCD display. You can change the channel LCD DISPLAY UPDATE Installation at any time using the Channel Up/Down buttons. To Change Customer Assistance Channels: REV. 7.19.17 Secondary Icons Press the Channel Up/Down button. If you are on Channel 88, pressing the Channel Up button will Currently On Channel 88 U VOX UIC advance to Channel 01. If you are on Channel 01, pressing GVHMFRS RNOotHicGeIRSOTARGMXTthhYaRGEVhdiioXCggeHMMuvahhuaCFEReetcinohssaMnScattnencc.phhnTraaeehnnlsennsDWeebaoallrenwniieissndgpn21hsb20oou,,ludtttthhnoteedhnnnewwwaCiidllilhllvloaaaacdnndcvncvuaeearnslncoUctenoepltyc/otDohaCaotchnwthhananenennlnbf1ieeurl)slt.8tt1o8p.n.rWe(fGosesrMaftoRahfSsettrhe A button and not during fast advance. B If the new channel selected is restricted to low power, the radio ATISVOX LOMEDHI SAMEwMillEauMtomatically switch to Low Power mode and the Low Power icon will appear on the LCD. If the radio is in the Key Lock mode, the channel will not change and the three (3) beep error signal will sound. SCAN Button SCAN Button Press and release the SCAN button to enter all scanning modes - Marine, GMRS and memory. See the Advanced Operation section has more details on using the Scan modes. The SCAN icon will display on the LCD display. Scanning begins at lower channels, and scans to higher channels. Press the Channel Up/ Down button to change the scan direction. Nothing Comes Close to a Cobra® 25