Cobra S200R User Guide - Page 1

S120R For iPhone User Guide NOTE: This device complies with part 15 of FCC rules: Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received including interference that may cause undesired operation. CAUTION: Modifications or parts not approved by Cobra Electronics Corporation may violate FCC Rules and void authority to operate this equipment. ©2013 Cobra Electronics Corporation Part No. 480-883-P Version A Printed in China Thank you for purchasing the Cobra iRadar S120R for iPhone, the world's first connected radar/laser detector. iRadar S120R uses Bluetooth® wireless technology to connect your iPhone®/iPod Touch® to display radar, laser and speed camera alerts. Follow these simple steps to get your iRadar S120R up and running. Cobra iRadar is made for iPod touch (5th Generation) iPod touch (4th Generation) iPhone 5 iPhone 4S iPhone 4 NOTE: Location-based alerts and GPS settings available only with iPhone. Only radar/laser alerts and settings will work with iPod touch. Trademark Acknowledgement Cobra® and the snake design are registered trademarks of Cobra Electronics Corporation, USA. iPhone® and iPod® touch are trademarks of Apple, Inc, registered with the U.S. and other countries. The Bluetooth® word mark is a registered trademark owned by Bluetooth SIG, Inc. and any use of such marks by Cobra Electronics Corporation is under license. Other trademarks and trade names are those of their respective owners. What's in the box? Cobra iRadar S120R Mounting bracket Screw, nut & bolt pack Cable-tie fasteners Setting Up iRadar S120R The S120R has been designed to be mounted under the hood, behind the vehicle's grille or within an air intake at the front of the vehicle if appropriate using the 'L' shaped bracket and screw pack provided. Find a suitable mounting position for the detector, ensuring that the front of the unit has a clear view of the road ahead and is unobstructed by any metallic objects and that there is a sufficient mounting area to attach the 'L' shaped fixing bracket. The S120R needs to be mounted in as horizontal a position as possible so that it is looking directly down the road ahead. We recommend that you mount the detector either behind the vehicle's grille (if the openings of the grille are at least 10mm in diameter) or within an air intake at the front of the vehicle. The S120R can be mounted anywhere at the front of the vehicle, but for optimum performance we suggest you mount it as close as possible to the license plate of the vehicle. Typical Fitting Typical Fitting 10mm Minimum When you have found a suitable location, using the 'L' shaped mounting bracket as a template, drill between 2 and 4 pilot holes into the selected mounting surface for attaching the bracket using either the self-tapping screws or the nuts and bolts provided. You will need to attach the bracket using at least 2 screws or 2 nuts and bolts to ensure that the bracket is well secured. Remember that there is a lot of vibration within the engine compartment so TityipsicvaelrFyititminpgortant that the S120R mounting bracket is secured correctly. Typical Fitting Typical Fitting Mounting Notes When mounting and connecting the power cables of the S120R ensure that you mount the unit and cables away from any moving parts such as aircooling fans or the fan belt. Position the unit so that device and power cables do not interfere with any moving parts within the engine compartment or interfer with any part of the vehicle that could endanger you or your passengers. Please check that all surfaces are safe to drill through before beginning any work. Connecting the iRadar S120R The S120R is powered by wiring it directly to your vehicles 12V electrical system using the cable supplied. Connect the red (positive) wire to a switched 12V ignition supply, this will power on the detector when the ignition is switched On, and Off when the ignition is Off. Connect the black (negative) wire to a chassis ground or battery ground. In many cases, this wire can be attached to any metal portion of the vehicle frame. The LED will blink red if the power connection has been completed successfully. This LED can be located near to the point where the power cable enters the rear of the device. It is not advisable to connect the S120R directly to the vehicle battery as after long periods of vehicle inactivity the vehicle battery may become discharged.