Compaq Armada 7700 33.6Kbps Modem Commands for Armada 7000 Family of Personal - Page 7

Connecting the Modem to a Cellular Phone, Choosing Cellular Direct Components, Registering the Phone

Page 7 highlights

: 3 +,7( $3(5 (cont.) NOTE: Use Windows HyperTerminal to enter Command Mode and register the phone with the modem. NOTE: $M3 is not supported by this modem. . . . . CHAPTER 2- BASICS OF CELLULAR PHONE USE . . . Connecting the Modem to a Cellular Phone . . The internal modem installed in the Armada 7000 Family of Personal Computers allows you to . connect a cellular phone in North America to your computer using an optional cable and the 25- . . . pin connector on the computer. There are AT commands associated with setting up and optimizing a cellular connection. . . . CAUTION: Using the wrong cable could cause permanent damage to the modem. Contact your Compaq authorized dealer, reseller, or service . provider for information on purchasing a cellular cable designed for this . modem. For a list of phone cables that are compatible with your modem, . refer to "Compatible Cellular Phones with Compaq Cables" in the Online . Reference Guide that is preinstalled on your computer. . . . Choosing Cellular Direct Components . . If you are using a cellular phone, you need to purchase the following items separately: . . N One of the models of cellular phones supported by this modem. . N Cellular phone connection cable. (Contact your Compaq authorized reseller or service . . provider.) . N Cellular airtime. (Contact a cellular carrier in your area.) . . . . Registering the Phone with the Modem . . . . When the modem was installed at the factory, it was not programmed to automatically expect a cellular phone connection. If you anticipate using a cellular phone with the modem, proceed as follows to register or setup the cellular phone with the modem. . . N Use $M1 if you are using a Motorola, JVC, or Pioneer phone. . N Use $M2 if you are using a Nokia, Technophone, AT&T (selected models), or Tandy phone. . . N Use $M4 if you are using a GE or Ericsson phone. . . This command needs be to issued only once; thereafter, the modem checks for the presence of . the phone. If a cellular phone is connected, the modem dials through the cellular phone; . otherwise, it uses a standard (RJ-11) telephone connector. . . . . . . . . . . . . . . . . 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61

(cont.)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
CHAPTER 2— B
ASICS OF
C
ELLULAR
P
HONE
U
SE
Connecting the Modem to a Cellular Phone
The internal modem installed in the Armada 7000 Family of Personal Computers allows you to
connect a cellular phone in North America to your computer using an optional cable and the 25-
pin connector on the computer. There are AT commands associated with setting up and
optimizing a cellular connection.
CAUTION:
Using the wrong cable could cause permanent damage to the
modem. Contact your Compaq authorized dealer, reseller, or service
provider for information on purchasing a cellular cable designed for this
modem. For a list of phone cables that are compatible with your modem,
refer to “Compatible Cellular Phones with Compaq Cables” in the
Online
Reference Guide
that is preinstalled on your computer.
Choosing Cellular Direct Components
If you are using a cellular phone, you need to purchase the following items separately:
One of the models of cellular phones supported by this modem.
Cellular phone connection cable. (Contact your Compaq authorized reseller or service
provider.)
Cellular airtime. (Contact a cellular carrier in your area.)
Registering the Phone with the Modem
When the modem was installed at the factory, it was not programmed to automatically expect a
cellular phone connection. If you anticipate using a cellular phone with the modem, proceed as
follows to register or setup the cellular phone with the modem.
Use
$M1
if you are using a Motorola, JVC, or Pioneer phone
.
Use
$M2
if you are using a Nokia, Technophone, AT&T (selected models), or Tandy phone
.
Use
$M4
if you are using a GE or Ericsson phone
.
This command needs be to issued only once; thereafter, the modem checks for the presence of
the phone. If a cellular phone is connected, the modem dials through the cellular phone;
otherwise, it uses a standard (RJ-11) telephone connector.
NOTE:
Use Windows HyperTerminal to
enter Command Mode and
register the phone with the
modem.
NOTE:
$M3
is not supported by this
modem.