Creative HN-900 HN-900 Quickstart - Page 4

Installing Battery, Using Headphones, Activating Noise Cancellation - noise canceling

Get Creative HN-900 PDF manuals and user guides View all Creative HN-900 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

EN A Installing Battery 1. Rotate right earcup cover counter-clockwise to reveal battery compartment. 2. Insert battery, noting polarity. Alkaline battery is recommended. 3. Rotate clockwise to close cover. 4. Replace battery when LED blinks. B Using Headphones 1. Connect the straight plug of the detachable cable to the left earcup socket. 2. Connect the L-shaped plug to your audio device. 3. For connection to an inflight system, plug into the airplane adapter beforehand. 4. You may listen to audio in passive mode when battery power is not supplied or Noise Cancellation is not activated. C Activating Noise Cancellation 1. To reduce external noise, turn on Noise Cancellation switch on the left earcup. The LED indicator will light up. 2. To use noise cancellation without audio, just detach the cable from your audio source. D Playback and Call Controls 1. Music playback control • Pause a song or video: Click mic button once. Click again to resume playback. • Skip to next song: Click mic button twice quickly. 2. Voice call control (iPhone) • Answer an incoming call or end current call: Click mic button once. • Accept call-waiting: Click mic button once during active call to switch. • Decline an incoming call or end call-waiting: Press and hold mic button for 2 seconds, then release. 2 beeps confirm your action. Note: Music playback control may not work on all MP3 players, mobile phones or computers Technical specifications: Headphones Drivers: 40mm Neodymium magnet Frequency Response: 20Hz ~ 20kHz Noise Reduction Level: -18dB (85%) Impedance: 290ohms* Sensitivity (1kHz): 100dB/mW* Microphone Type: Omni-directional Frequency Response: 100Hz ~ 10kHz Impedance:

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
EN
Installing Battery
Using Headphones
Activating Noise Cancellation
Playback and Call Controls
A
B
C
D
1.
Rotate right earcup cover counter-clockwise to reveal battery compartment.
2. Insert battery, noting polarity. Alkaline battery is recommended.
3. Rotate clockwise to close cover.
4. Replace battery when LED blinks.
1.
Connect the straight plug of the detachable cable to the left earcup socket.
2. Connect the L-shaped plug to your audio device.
3. For connection to an inflight system, plug into the airplane adapter
beforehand.
4. You may listen to audio in passive mode when battery power is not
supplied or Noise Cancellation is not activated.
Technical specifications:
Headphones
Drivers: 40mm Neodymium magnet
Frequency Response: 20Hz ~ 20kHz
Noise Reduction Level: -18dB (85%)
Impedance: 290ohms*
Sensitivity (1kHz): 100dB/mW*
Microphone
Type: Omni-directional
Frequency Response: 100Hz ~ 10kHz
Impedance: <2.2kohms
Sensitivity (1kHz): -38dBV/Pa
Cable Length: 1.5m detachable with inline microphone
Power Supply: 1xAAA alkaline battery
Battery Life: 40hours
Product Weight: 168g
* Specifications measured in active Noise Cancellation mode
1. To reduce external noise, turn on Noise Cancellation switch on the
left earcup. The LED indicator will light up.
2. To use noise cancellation without audio, just detach the cable from
your audio source.
1. Music playback control
•
Pause a song or video: Click mic button once. Click again to
resume playback.
• Skip to next song: Click mic button twice quickly.
2. Voice call control (iPhone)
• Answer an incoming call or end current call: Click mic button once.
• Accept call-waiting: Click mic button once during active call
to switch.
• Decline an incoming call or end call-waiting: Press and hold mic
button for 2 seconds, then release. 2 beeps confirm your action.
Note:
Music playback control may not work on all MP3 players,
mobile phones or computers