Cub Cadet 933 SWE 930 SWE Operator's Manual - Page 21

Important

Get Cub Cadet 933 SWE PDF manuals and user guides View all Cub Cadet 933 SWE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

5. Holding the friction wheel assembly, slide the hex shaft out 10. Slide the hex shaft through the right side of the frame of the right side of the frame. The spacer on the left side toward the left side and through the friction wheel of the hex shaft will fall and the sprocket should remain assembly. hanging lose in the chain. NOTE: If the sprocket fell from the snow thrower chain while 6. Lift the friction wheel assembly out between the axle shaft removing the hex shaft, position the hex hub of the sprocket and the drive shaft assemblies. toward the friction wheel and place the sprocket in the chain. 7. Remove four screws securing the friction wheel to the hub 11. After making certain that the chain is on both the large assembly (refer to Figure 7-11). Discard old friction wheel. and the small sprocket, align the hex shaft with the hex hub of the small sprocket, and slide the shaft through the sprocket. 12. Slide the spacer onto the end of the hex shaft. 13. Align the bearing on the right end of the hex shaft with the hole in the right side of the frame, then push the hex shaft to the left into position in the frame. 14. Slide the bearing onto the left end of the hex shaft and press into the hole on the left side the frame. 15. Place the belleville washer (rounded side toward head) onto the hex screw removed earlier, and insert the screw into the threaded hole of the hex shaft. 16. Using a 3/4" wrench holding the hex shaft, gradually tighten the hex screw to fully seat the bearings in each side of the frame and to secure the hex shaft. 17. Position the frame cover on the bottom of the frame and secure with the self-tapping screws, and re-install the right wheel. Pivot the snow thrower down to its normal operating position. Figure 7-11 IMPORTANT: Repeat the drive control test from the Assembly & Set-Up section of this manual before operating the snow 8. Reassemble the new friction wheel onto the hub assembly, thrower. tightening the four screws in rotation to 6-9 ft.-lbs. It is important to assemble the friction wheel symmetrically for proper functioning. Refer to Figure 7-11. 9. Reposition the friction wheel assembly in the snow thrower frame. Insert the pin from the shift arm assembly into the friction wheel assembly and hold assembly in position. Refer to Figure 7-12. Figure 7-12 Section 7 - Service 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
10.
Slide the hex shaft through the right side of the frame
toward the left side and through the friction wheel
assembly.
NOTE:
If the sprocket fell from the snow thrower chain while
removing the hex shaft, position the hex hub of the sprocket
toward the friction wheel and place the sprocket in the chain.
11.
After making certain that the chain is on both the large
and the small sprocket, align the hex shaft with the hex
hub of the small sprocket, and slide the shaft through the
sprocket.
12.
Slide the spacer onto the end of the hex shaft.
13.
Align the bearing on the right end of the hex shaft with the
hole in the right side of the frame, then push the hex shaft
to the left into position in the frame.
14.
Slide the bearing onto the left end of the hex shaft and
press into the hole on the left side the frame.
15.
Place the belleville washer (rounded side toward head)
onto the hex screw removed earlier, and insert the screw
into the threaded hole of the hex shaft.
16.
Using a 3/4” wrench holding the hex shaft, gradually
tighten the hex screw to fully seat the bearings in each side
of the frame and to secure the hex shaft.
17.
Position the frame cover on the bottom of the frame and
secure with the self-tapping screws, and re-install the
right wheel. Pivot the snow thrower down to its normal
operating position.
IMPORTANT:
Repeat the drive control test from the Assembly
& Set-Up section of this manual before operating the snow
thrower.
5.
Holding the friction wheel assembly, slide the hex shaft out
of the right side of the frame. The spacer on the left side
of the hex shaft will fall and the sprocket should remain
hanging lose in the chain.
6.
Lift the friction wheel assembly out between the axle shaft
and the drive shaft assemblies.
7.
Remove four screws securing the friction wheel to the hub
assembly (refer to Figure 7-11). Discard old friction wheel.
Figure 7-11
8.
Reassemble the new friction wheel onto the hub assembly,
tightening the four screws in rotation to 6-9 ft.-lbs. It is
important to assemble the friction wheel symmetrically for
proper functioning. Refer to Figure 7-11.
9.
Reposition the friction wheel assembly in the snow thrower
frame. Insert the pin from the shift arm assembly into the
friction wheel assembly and hold assembly in position.
Refer to Figure 7-12.
Figure 7-12
21
S
ECTION
7 — S
ERVICE