CyberPower PR1000LCDRT1U User Manual - Page 2

LCD SETUP FUCTIONS Set-up Mode Step 1: The machine enters Set-Up Mode after holding the Display toggle for 10 seconds. Step 2: By pressing the Display toggle, users can switch between setup functions. User configurable functions are as follows: a. Sensitivity: Set the level of tolerance for UPS. Increase the UPS compatibility for local utility power condition. High: The UPS will turn to battery power more often to provide the steady power supply to the connected equipment. Low: The UPS will tolerate more fluctuations and turn to battery power less often. b. Battery Lifetime: Show the batteries already used time. Reset the logger when battery module replacement or first time installation. c. Firmware Version: Show the UPS version number. Items Unit The settable items are sorted by unit as in the following table： 1 Sensitivity 2 Step 3: Press and hold the toggle for 4 seconds. When the icons blink, the value of each item can be changed by slightly pressing the toggle. 3 Battery Lifetime Firmware Version Step 4: To save the value and return to general mode, press and hold the toggle for 4 seconds. Year Note: If the machine is left idle for over 30 seconds during setup, it will turn off the backlight and return to general mode automatically. Note: If user wants to return to general mode without saving changes, there are two methods: 1. Wait for the backlight to turn off 2. Press and hold the "Display" toggle for 10 seconds TROUBLE SHOOTIMG Problem Outlet do not provide power to equipment The UPS does not perform expected runtime. The UPS will not turn on. Possible Cause Circuit breaker has tripped due to an overload. Batteries are discharged Unit has been damaged by a surge or spike. Uncritical outlets have turned off automatically due to an overload Battery not fully charged. Battery is degraded The on/off switch is designed to prevent damage by rapidly turning it off and on. The unit is not connected to an AC outlet. The battery is worn out. Mechanical problem. Solution Turn the UPS off and unplug at least one piece of equipment. Wait 10 seconds, reset the circuit breaker by depressing the button, and then turn the UPS on. Recharge the unit for at least 4 hours Contact CyberPower Systems about replacement batteries at [email protected] Push the toggle button to make the uncritical outlets turn on. Recharge the battery by leaving the UPS plugged in. Contact CyberPower Systems about replacement batteries at [email protected] Turn the UPS off. Wait 10 seconds and then turn the UPS on. The unit must be connected to a 110/120v outlet. Contact CyberPower Systems about replacement batteries at [email protected] Contact CyberPower Systems at [email protected] The serial cable or USB cable Connect the cable to the UPS unit. You must use the cable that is not connected. came with the unit. PowerPanel® Personal Edition is inactive The cable is connected to the wrong port. The unit is not providing battery power. The serial cable is not the cable that was provided with the unit. Try another port of your computer Shutdown your computer and turn the UPS off. seconds and turn the UPS back on. This should reset the unit. You must use the cable included with the unit for the software Additional troubleshooting information can be found at www.cyberpowersystems.com/support.htm Wait 10 TECHNICAL SPECIFICATIONS Model Capacity(VA) Capacity(Watts) Input Input Plug Type Input Voltage Range Input Frequency Range Output On Battery Output Voltage On Battery Output Frequency Transfer Time(Typical) Overload Protection Surge Protection and Filtering Lightning/Surge Protection Physical Output Receptacles Dimensions(in) Weight (lb) Battery Battery Model Hot Swappable Battery Warning Diagnostics Indicators Audible Alarms Environmental Operating Temperature Operating Relative Humidity Operating Elevation Communication PowerPanel ®Business Edition Management Self-Test Auto-Charger/ Auto-Restart COM Interface Built-in USB Interface SNMP/ HTTP Network Slot Safety Approvals PR500LCDRT1U 500 400 PR750LCDRT1U 750 600 PR1000LCDRT1U 1000 800 NEMA 5-15P 80Vac-150Vac 60Hz+/-3Hz(auto sensing) Pure Sine Wave at 120Vac+/-5% 60Hz+/-1% 4 ms On Utility: Circuit Breaker, On Battery: Internal Current Limiting Yes (6)NEMA 5-15R+(1)NEMA 5-15R Surge Only 1U Rack, 17.25'' x 9.1'' x 1.75'' 1U Rack, 17.25'' x 16.8'' x 1.75'' 19.8 30.7 35.9 RB0690X2A RB0670X4A Yes RB0690X4B Power On, Wiring Fault, LCD Display (Using Battery, AVR, Load Level, Battery Level) On Battery, Low Battery, Overload 32oF to 104oF ( 0oC to 40 oC ) 0 to 95% Non-Condensing 0-10000 feet (0-3000 meters) Windows 98/ME/NT/2000/XP/Vista/7 Manual Self-Test Yes True RS232 x1 Yes Yes UL1778,cUL107,FCC Part 15 Class A,CSA CYBERPOWER GREENPOWER UPS™ TECHNOLOGY GreenPower UPS™ The CyberPower GreenPower UPS™ cuts UPS energy costs by up to 75% compared to the conventional UPS circuits. Conventional UPS systems pass power through a transformer to provide normal output voltage to protected devices. By contrast, the GreenPower UPS™ circuitry bypasses the transformer when utility power is normal, significantly increasing the power efficiency of the UPS. As a result, a GreenPower UPS™ produces less heat and uses less energy reducing energy costs. When utility power is abnormal, the GreenPower UPS™ operates like a normal UPS. Since utility power operates normally 88% of the time, the GreenPower UPS™ operates primarily in its cost-cutting bypass mode. LIMITED WARRANTY AND CONNECTED EQUIPMENT GUARNTEE EEGUARANTEE Read the following terms and conditions carefully before using the CyberPower PR500LCDRT1U/PR750LCDRT1U/PR1000LCDRT1U (the "Product"). By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty and Connected Equipment Guarantee (together referred to as this "Warranty"). If you do not agree to the terms and conditions of this Warranty, you should return the Product for a full refund prior to using it. Who is Providing this Warranty? CyberPower Systems (USA), Inc. ("CyberPower") provides this Limited Warranty. What Does This Warranty Cover? This warranty covers defects in materials and workmanship in the Product under normal use and conditions. It also covers equipment that was connected to the Product and damaged because of the failure of the Product. What is the Period of Coverage? This warranty covers the Product for three years and connected equipment for as long as you own the Product. Who Is Covered? This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product. How Do You Get Service? 1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379 or send us an e-mail message at [email protected] for instructions. 2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and Request a Claim Number. 3. You must provide a dated Proof-of-Purchase receipt (or other proof of the original purchase) and provide a description of the defect. 4. Pack and ship the product with a dated Proof- of-Purchase receipt to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the shipping label or include it with the product. You must prepay all shipping costs, you are responsible for packaging and shipment, and you must pay the cost of the repair estimate. How Long Do I Have To Make A Claim? All claims must be made within ten days of the occurrence. What Will We Do To Correct Problems? CyberPower will inspect and examine the Product. If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund to you the full purchase price you paid for the Product (purchase receipt showing price paid is required). If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the connected equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or another a third-party valuation guide, or eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to $400,000 for PR500LCDRT1U/PR750LCDRT1U/PR1000LCDRT1U. Who Pays For Shipping? We pay when we send items to you; you pay when you send items to us. What Are Some Things This Warranty Does Not Cover? 1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software. 2. This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or maintenance, or use with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums, medical or life support devices, etc. What Other Limitations Apply? 1. This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use of any adapters or other connectors. 2. The Product must have been plugged directly into the power source and the equipment connected to the Product must be directly connected to the Product and not "daisy-chained" together in serial fashion with any extension cords, another Product or device similar to the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty. 3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in conformance with any license, instruction manual, or warnings provided with the Product and the equipment connected to it. 4. The Product must have been used at all times within the limitations on the Product's VA capacity. What are the Limitations? The sole and exclusive remedies of the Initial Customer are those provided by this Warranty. The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or impulses from lightning or other power transients. If it can be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence will be deemed outside the rated capabilities of the Product and the Limited Warranty is void. CyberPower Does Not Cover or Undertake Any Liability in Any Event for Any of the Following: 1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software. 2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and code-compliant 120 volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land lines, PBX telephone equipment lines or Base 10/100T Ethernet lines, when properly installed and connected. (This exclusion applies, for example, to fluctuations in data transmission or reception, by CATV or RF transmission or fluctuations, or by transients in such transmission.) 3. Damage from any circumstance described as excluded above with respect to the Product. 4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the product or the Connected Equipment. 5. CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee. CyberPower excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or loss of property [EXCEPT FOR (AND ONLY FOR) the specific limited agreement of CyberPower to provide certain warranty benefits regarding "Connected Equipment" under this Warranty], loss of profits, business interruption, or loss of information or data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation may not apply to you. 6. The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in hazardous environments requiring fail-safe performance, or for use in any circumstance in which the failure of the Product could lead directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical or life support device (collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of fitness for High Risk Activities or with aquariums. CyberPower does not authorize use of any Product in any High Risk Activities or with Aquariums. ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT. What is the Fine Print? The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded. CyberPower is the warrantor under this Limited Warranty. For further information please feel free to contact CyberPower at Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400, Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at [email protected]. Recycle Policy CyberPower Systems encourages environmentally sound methods for disposal and recycling of its UPS products. Please dispose and/or recycle your UPS and batteries in accordance to the local regulations of your state. FCC Notice This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING!! This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. Shielded signal cables must be used with this product to ensure compliance with the Class A FCC limits. The Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulation. Cet appareil numerique de la class A respecte toutes les exigencies du Reglement sur le materiel brouilleur du Canada