CyberPower RMCARD205 User Manual 1 - Page 35

Command Line Interface - default login

Get CyberPower RMCARD205 PDF manuals and user guides View all CyberPower RMCARD205 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

Command Line Interface CyberPower Remote Management System How to log on Users can log on to the command line interface through either console network access (Telnet or SSH) or local access (Serial port). 1. Network access to the command line interface When user logs in with the admin username and admin password through Telnet or SSH, there are two types of interfaces available. One is the command line interface (CLI) and the second is a menu interface. The default is CLI. If the user wants to change to the menu interface, type in the [menumode] command. To switch back to CLI, it is necessary to logout and login to the RMCARD. How to use telnet access command line interface Step 1: Need to make sure the computer has access to the RMCARD installed network. At a command prompt, type telnet and the IP address for the RMCARD (for example, telnet 139.225.6.133, when the RMCARD uses the default Telnet port of 23), and press Enter. Step 2: Enter the user name and password (by default, user name: cyber, password: cyber) How to use SSH access command line interface SSH is highly recommended for using to access the command line interface. SSH encrypts user names, passwords, and transmitted data. To use SSH you must first configure SSH and install an SSH client program (eg. PuTTY, HyperTerminal, or Tera Term) on your computer. Note: If using PuTTY to configure SSH access, please configure Line discipline of Terminal to "Force off", as shown in Figure 5. Figure 5. The PuTTY Configuration window. 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
CyberPower Remote Management System
35
Command Line Interface
How to log on
Users can log on to the command line interface through either console network access (Telnet or SSH)
or local access (Serial port).
1. Network access to the command line interface
When user logs in with the admin username and admin password through Telnet or SSH, there are two
types of interfaces available. One is the command line interface (CLI) and the second is a menu
interface. The default is CLI. If the user wants to change to the menu interface, type in the [menumode]
command. To switch back to CLI, it is necessary to logout and login to the RMCARD.
How to use telnet access command line interface
Step 1: Need to make sure the computer has access to the RMCARD installed network. At a command
prompt, type telnet and the IP address for the RMCARD (for example, telnet 139.225.6.133,
when the RMCARD uses the default Telnet port of 23), and press Enter.
Step 2: Enter the user name and password (by default, user name: cyber, password: cyber)
How to use SSH access command line interface
SSH is highly recommended for using to access the command line interface. SSH encrypts user
names, passwords, and transmitted data. To use SSH you must first configure SSH and install an SSH
client program (eg. PuTTY, HyperTerminal, or Tera Term) on your computer.
Note:
If using PuTTY to configure SSH access, please configure Line discipline of Terminal to
“Force
off”
, as shown in Figure 5.
Figure 5. The PuTTY Configuration window.