D-Link 300T User Manual - Page 8

Information Required for Installation, Information you will need from your ADSL service provider: - dsl configuration

Get D-Link 300T - DSL - 8 Mbps Modem PDF manuals and user guides View all D-Link 300T manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

DSL-300T DSL Modem User's Guide Information Required for Installation Information you will need from your ADSL service provider: Username This is the Username used to log on to your ADSL service provider's network. It is commonly in the form − [email protected]. Your ADSL service provider uses this to identify your account. Password This is the Password used, in conjunction with the Username above, to log on to your ADSL service provider's network. This is used to verify the identity of your account. Connection Protocol This is the method your ADSL service provider uses to send and receive data between the Internet and your computer. Your Modem supports the following connection protocols: PPPoE, PPPoA, CLIP (IPoA) and Bridge. Security Protocol This is the method your ADSL service provider will use to verify your Username and Password when you log on to their network. Your Modem supports the PAP and CHAP protocols. This is the Virtual Path Identifier (VPI). It is used in VPI conjunction with the Virtual Channel Identifier (VCI) below, to identify the data path between your ADSL service provider's network and your computer. This is the Virtual Channel Identifier (VCI). It is used in VCI conjunction with the VPI above to identify the data path between your ADSL service provider's network and your computer. Record info here Information you will need to change settings on the DSL-300T Modem: Username This is the Username needed access the Modem's management interface. When you attempt to connect to the device through a web browser you will be prompted to enter this Username. The default Username for the Modem is admin. This may be changed by the user. Record info here Password This is the Password you will be prompted to enter when you access the Modem's management interface. The default Password is admin. This may be changed by the user. LAN IP addresses for the DSL-300T This is the IP address you will enter into the Address field of your web browser to access the Modem's configuration graphical user interface (GUI) using a web browser. The default IP address is 192.168.1.1 and it is referred to as the "Management IP" address in this User's Manual. This may be changed to suit any IP address scheme the user desires. This address will be the base IP address used for DHCP service on the LAN when DHCP is enabled. LAN Subnet Mask for the DSL-300T This is the subnet mask used by the DSL-300T, and will be used throughout your LAN. The default subnet mask is 255.255.255.0. This can be changed later. viii

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
DSL-300T DSL Modem User’s Guide
Information Required for Installation
Information you will need from your ADSL service provider:
Username
This is the Username used to log on to your ADSL
service provider’s network. It is commonly in the form
−
[email protected]. Your ADSL service provider uses this
to identify your account.
Record info here
Password
This is the Password used, in conjunction with the
Username above, to log on to your ADSL service
provider’s network. This is used to verify the identity of
your account.
Connection Protocol
This is the method your ADSL service provider uses to
send and receive data between the Internet and your
computer. Your Modem supports the following
connection protocols: PPPoE, PPPoA, CLIP (IPoA) and
Bridge.
Security Protocol
This is the method your ADSL service provider will use
to verify your Username and Password when you log
on to their network. Your Modem supports the PAP and
CHAP protocols.
VPI
This is the Virtual Path Identifier (VPI). It is used in
conjunction with the Virtual Channel Identifier (VCI)
below, to identify the data path between your ADSL
service provider’s network and your computer.
VCI
This is the Virtual Channel Identifier (VCI). It is used in
conjunction with the VPI above to identify the data path
between your ADSL service provider’s network and
your computer.
Information you will need to change settings on the DSL-300T Modem:
Username
This is the Username needed access the Modem’s
management interface. When you attempt to connect to
the device through a web browser you will be prompted
to enter this Username. The default Username for the
Modem is
admin
. This may be changed by the user.
Record info here
Password
This is the Password you will be prompted to enter
when you access the Modem’s management interface.
The default Password is
admin
. This may be changed
by the user.
LAN IP addresses for
the DSL-300T
This is the IP address you will enter into the Address
field of your web browser to access the Modem’s
configuration graphical user interface (GUI) using a
web browser. The default IP address is 192.168.1.1
and it is referred to as the “Management IP” address in
this User’s Manual. This may be changed to suit any IP
address scheme the user desires. This address will be
the base IP address used for DHCP service on the LAN
when DHCP is enabled.
LAN Subnet Mask for
the DSL-300T
This is the subnet mask used by the DSL-300T, and
will be used throughout your LAN. The default subnet
mask is
255.255.255.0
. This can be changed later.
viii