D-Link DES-5664TX User Guide - Page 20

Installing Modules

Get D-Link DES-5664TX - DES 5600 Switch PDF manuals and user guides
UPC - 790069226427
View all D-Link DES-5664TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Fast Ethernet Switching System User's Guide Installing Modules The process for installing all modules is the same. You cannot change the position of the CPU module. It must remain in the CPU slot. The DES-5600 will not work unless the CPU module is installed in the CPU slot. You can purchase modules separately in order to meet the needs of your network. The procedure for installing all modules is the same. Follow these steps to install modules: 1. Power the DES-5600 off before installing or removing modules. None of the modules are hot swappable. Removing or installing modules while the DES-5600 is powered on can damage the DES5600 and the modules. 2. Grasp the thumbscrews on the side of the module or blank bracket and turn counterclockwise to unscrew them. Remove the old module or the blank bracket and set aside. Do not discard the module or blank bracket. Put the old module or blank bracket back in if you remove the new module. 3. Install the new module by inserting it into the guides, see Figure 7, and sliding it in until it stops. Press in firmly until you feel the module snap into place. The module should be level and flush with the rest of the DES-5600 Never force, twist or bend the module. The module slides in smoothly. 4. Gently push the thumbscrews in and turn clockwise to tighten. Do not over tighten the thumbscrews. 5. Power the DES-5600 on after the new module is installed. The DES-5600 will auto detect the module and it will appear on the menu. 6. The 100BASE-FX and 1000-BASE-SX ports have dust covers over the transceivers. Remove the dust covers before plugging in the cable. 7. Check the LEDs to verify that there is a link at the port. Installing the DES-5600 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Fast Ethernet Switching System User’s Guide
Installing the DES-5600
13
Installing Modules
The process for installing all modules is the same. You cannot change the position
of the CPU module. It must remain in the CPU slot. The DES-5600 will not work
unless the CPU module is installed in the CPU slot.
You can purchase modules separately in order to meet the needs of your network.
The procedure for installing all modules is the same. Follow these steps to install
modules:
1.
Power the DES-5600 off before installing or removing modules.
None of the modules are hot swappable. Removing or installing
modules while the DES-5600 is powered on can damage the DES-
5600 and the modules.
2.
Grasp the thumbscrews on the side of the module or blank bracket
and turn counterclockwise to unscrew them. Remove the old
module or the blank bracket and set aside. Do not discard the
module or blank bracket. Put the old module or blank bracket back
in if you remove the new module.
3.
Install the new module by inserting it into the guides, see Figure 7,
and sliding it in until it stops. Press in firmly until you feel the
module snap into place. The module should be level and flush with
the rest of the DES-5600 Never force, twist or bend the module.
The module slides in smoothly.
4.
Gently push the thumbscrews in and turn clockwise to tighten. Do
not over tighten the thumbscrews.
5.
Power the DES-5600 on after the new module is installed. The
DES-5600 will auto detect the module and it will appear on the
menu.
6.
The 100BASE-FX and 1000-BASE-SX ports have dust covers
over the transceivers. Remove the dust covers before plugging in
the cable.
7.
Check the LEDs to verify that there is a link at the port.