D-Link DVG-G1402S Product Manual
D-Link DVG-G1402S - Wireless Broadband VoIP Router Manual
 |
UPC - 790069270390
View all D-Link DVG-G1402S manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DVG-G1402S manual content summary:
- D-Link DVG-G1402S | Product Manual - Page 1
- D-Link DVG-G1402S | Product Manual - Page 2
DVG-G1402S User's Manual Table of Contents Table of Contents Package Contents ...3 Introduction...4 Features and Benefits 5 Hardware Overview 6 Wireless Basics ...8 Wireless Installation Considerations 9 Getting Started ...10 Using the Configuration Utility 13 Setup Wizard...14 Wireless Settings - D-Link DVG-G1402S | Product Manual - Page 3
DVG-G1402S User's Manual Package Contents Package Contents Your DVG-G1402S purchase includes the following: D-Link DVG-G1402S Wireless G VoIP Router Manual and Warranty on CD Ethernet Cable Standard RJ-11 Phone Cable Quick Installation Guide 12VDC 1.25A Power Adapter If any of the - D-Link DVG-G1402S | Product Manual - Page 4
DVG-G1402S User's Manual Introduction Introduction D-Link® introduces the DVG-G1402S Broadband VoIP Wireless Router. The DVG-G1402S is designed for homes or small businesses ready to wirelessly share Internet access and enable Voice over IP. The DVG-G1402S maximizes your broadband investment by - D-Link DVG-G1402S | Product Manual - Page 5
Manual Features and Benefits Features and Benefits Voice over IP Technology SIP Technology Simple and Easy Installation Quality of Service (QoS) Built-in Switch Remote Configuration Wirelessly Share Your Internet Connection The DVG-G1402S allows users to use a regular telephone connected to the VoIP - D-Link DVG-G1402S | Product Manual - Page 6
DVG-G1402S is receiving/transmitting from/to the wireless network. Alarm LED The Alarm LED will light solid red if the self-test or bootup fails. The LED will flash red slowly when the device is booting. Prov LED A blinking light indicates the router is attempting to connect with the VoIP service - D-Link DVG-G1402S | Product Manual - Page 7
DVG-G1402S User's Manual Rear Panel Hardware Overview Antenna Connect to a wireless network. Reset Button This button will restore the factory default settings of the DVG-G1402S. LAN Ports (1-4) Connect to your Ethernet enabled computers using Ethernet cabling. Phone Port (1-2) Connect to your - D-Link DVG-G1402S | Product Manual - Page 8
DVG-G1402S User's Manual Wireless Basics Wireless Basics D-Link wireless products are based on industry standards to provide easy-to-use and compatible high-speed wireless connectivity within your home, business or public access wireless networks. D-Link wireless products will allow you access to - D-Link DVG-G1402S | Product Manual - Page 9
DVG-G1402S User's Manual Wireless Installation Considerations Wireless Installation Considerations The D-Link DVG-G1402S lets you access your network, using a wireless connection, from virtually on range.Try to position access points, wireless routers, and computers so that the signal passes - D-Link DVG-G1402S | Product Manual - Page 10
DVG-G1402S User's Manual Getting Started Getting Started If your computer connects directly to a DSL or Cable modem and does not connect to a router, follow the steps below to install your DVG-G1402S. After the steps are completed, your setup should look similar to the diagram below. D-Link - D-Link DVG-G1402S | Product Manual - Page 11
's IP settings to DHCP (to automatically be assigned an IP address from the DVG-G1402S) regardless of what type of Internet connection you have (Please refer to your NIC card's manual for detailed information). If your cable service provider does not require a MAC address, setup of the DVG-G1402S - D-Link DVG-G1402S | Product Manual - Page 12
PC. By default the unit is already configured to work behind a router. Be sure to change your computer's IP settings to DHCP (to automatically be assigned an IP address from the DVG-G1402S) regardless of what type of internet connection you have. (Please refer to your NIC card's manual for detailed - D-Link DVG-G1402S | Product Manual - Page 13
(TCP/IP). Set your PC's IP address to 192.168.15.15 and the subnet mask to 255.255.255.0. The default gateway and primary DNS server IP addresses should be the LAN IP address of the DVG-G1402S router (192.168.15.1). Click OK. In order to use a web browser to configure the VoIP Router you must - D-Link DVG-G1402S | Product Manual - Page 14
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Click Run Wizard. Click Next. Enter a NTP server or leave blank to use the default server. Select your time zone from the drop-down menu. Click Next. D-Link Systems, Inc. 14 - D-Link DVG-G1402S | Product Manual - Page 15
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Select a channel. For best results, use 1, 6, or 11. Enter the SSID, or Service Set Identifier, which is the workgroup name of your Wireless 8 and 63 characters. Click Next. D-Link Systems, Inc. 15 - D-Link DVG-G1402S | Product Manual - Page 16
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) If you selected Dynamic, enter a host name (optional) and click Clone MAC Address. Click Next. If you selected Static, enter the IP address, subnet mask, default gateway, and DNS server(s) supplied - D-Link DVG-G1402S | Product Manual - Page 17
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > Wireless > LAN Basic Wireless LAN Usage: Select Enabled or Disabled. Disabled will turn off the wireless function of the router. Wireless LAN Mode: Select the wireless mode of your network - D-Link DVG-G1402S | Product Manual - Page 18
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Wireless Security The DVG-G1402S offers 3 types of wireless security - WEP, WPA-PSK, and WPA. WEP (Wired Equivalent Privacy) is a method of encrypting data for wireless communication intended to - D-Link DVG-G1402S | Product Manual - Page 19
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > Wireless > LAN Authorization Authorization Type: Select the encryption/authentication type: No Auth - Select if no encryption/authentication is being used on your wireless network. WEP - - D-Link DVG-G1402S | Product Manual - Page 20
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > Wireless > LAN Authorization (WEP) Auth Method: Select the type of authentication: Open Auth - Any wireless client can associate with the wireless router but cannot exchange data unless the - D-Link DVG-G1402S | Product Manual - Page 21
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > Wireless > LAN Authorization (WPA) Radius Server: Enter the IP address of your RADIUS server. Port: Enter the port used (default is 1812). Secret: Enter the security key. Group Key Interval: - D-Link DVG-G1402S | Product Manual - Page 22
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > Wireless > LAN Authorization (WPA-PSK) Passphrase: Enter a key (passphrase). The key is an alpha-numeric password between 8 and 63 characters long. The password can include symbols (!?*&_) - D-Link DVG-G1402S | Product Manual - Page 23
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > Wireless > MAC Address Filter MAC Address: Enter the MAC address of the wireless client you would like to allow wireless connectivity to the router. State: Select Enabled or Disabled. Apply: - D-Link DVG-G1402S | Product Manual - Page 24
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > WAN > Dynamic IP Host Name: Enter a host name. Most ISPs do not require this. MAC Address: Manually enter the MAC address of the computer that was last connected directly to the Internet. - D-Link DVG-G1402S | Product Manual - Page 25
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > WAN > Static IP IP Address: Enter the IP address supplied by your ISP. Subnet Mask: Enter the subnet mask. Default Gateway: Enter the default gateway. Primary/Secondary DNS Address: Enter - D-Link DVG-G1402S | Product Manual - Page 26
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > WAN > PPPoE User Name: Enter your PPPoE user name. Password: Enter your PPPoE password. Retype Password: Enter your PPPoE password again. Primary/Secondary DNS Address: You may enter the DNS - D-Link DVG-G1402S | Product Manual - Page 27
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > LAN IP Address: Enter the IP address you want to assign to the DVG-G1402S router. Subnet Mask: Enter the subnet mask. Apply: Click Apply to save your settings. D-Link Systems, Inc. 27 - D-Link DVG-G1402S | Product Manual - Page 28
the IP settings on all your other network devices. Start IP Address: Enter the starting IP address of the IP address range you want to assign to your network devices. Gateway: Enter the default gateway you want to assign to your devices. This is usually the (LAN) IP address of the DVG-G1402S. IP - D-Link DVG-G1402S | Product Manual - Page 29
IP address of the DVG-G1402S. MAC Address: Manually enter the MAC address of the computer or device you want to assign. DHCP Client: Select a device that has already been assigned an address from the drop-down list. Select it and then click the Clone button. Apply: Click Apply to save your settings - D-Link DVG-G1402S | Product Manual - Page 30
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Home > Proxy DNS State: Select Enabled or Disabled. Proxy DNS IP Address: Enter the IP address of the Proxy server. Apply: Click Apply to save your settings. D-Link Systems, Inc. 30 - D-Link DVG-G1402S | Product Manual - Page 31
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > Virtual Server Private IP: Enter the IP address of the computer you want to open port(s) to. Protocol Type: Select the protocol type: TCP, UDP, or Both. Start Global Port: Enter the - D-Link DVG-G1402S | Product Manual - Page 32
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > FIlter > IP Filter Pass or Block: Select Block or Pass. Protocol: Select the protocol type: TCP, UDP, or Both. IP Address - Source: Enter the IP address of the source computer. IP - D-Link DVG-G1402S | Product Manual - Page 33
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > FIlter > MAC Filter MAC Address: Enter the MAC address of the wired computer or device to allow connectivity to the DVG-G1402S. State: Select to enable or disable the rule. Apply: Click - D-Link DVG-G1402S | Product Manual - Page 34
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > Firewall Pass or Block: Enter the MAC address of the computer or device to allow connectivity to the DVG-G1402S. Protocol: Select to enable or disable the rule. IP Address Source: Enter - D-Link DVG-G1402S | Product Manual - Page 35
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > Firewall (continued) TCP Flag: Check the box to enable each of the optional - D-Link DVG-G1402S | Product Manual - Page 36
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > RIP RIP - Routing Information Protocol specifies how routers exchange information. With RIP, routers periodically exchange entire tables. LAN Version: Select RIPv1 or RIPv2. LAN State: - D-Link DVG-G1402S | Product Manual - Page 37
DVG-G1402S User's Manual IP Address of the gateway used for traffic destined for the specified subnet or device. Interface: Select WAN or LAN. Metric: Type in the maximum number of hops allowed for the static route. State: Enable or disable the route. Apply: Click Apply to save your settings. D-Link - D-Link DVG-G1402S | Product Manual - Page 38
> NAT Configuration NAT Interface IP Address: Displays the IP address of the LAN port on the DVG-G1402S. NAT Interface Netmask: Displays the subnet mask of the LAN port on the DVG-G1402S. NAT Function: Select Enabled or Disabled. Apply: Click Apply to save your settings. D-Link Systems, Inc. 38 - D-Link DVG-G1402S | Product Manual - Page 39
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > NAT > Dynamic NAT Global IP Start: Enter the start of the global IP range. Global IP End: Enter the end of the global IP range. Local IP Start: Enter the start of the local IP range. - D-Link DVG-G1402S | Product Manual - Page 40
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Advanced > NAT > Static NAT Local IP Address: Enter the local IP address you wish to redirect globally. Global IP Address: Enter the global IP address you wish to redirect locally. Apply: Click - D-Link DVG-G1402S | Product Manual - Page 41
that you try opening ports from the Virtual Server or Firewall settings before using DMZ. DMZ Host IP Address: Enter the IP address of the computer/device you want to forward all ports to. Signaling TOS: This is used to set type of service value in IP header for VoIP signaling RTP ToS: This - D-Link DVG-G1402S | Product Manual - Page 42
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration default setting (for most cable providers) is 1500. Most DSL providers use 1492. UPnP: Select to enable or disable UPnP™ (Universal Plug and Play). IPSec Passthrough/PPTP Passthrough: The device supports VPN (Virtual - D-Link DVG-G1402S | Product Manual - Page 43
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Tools > Admin Web Port Number: Enter the port number to use when accessing the web-based configuration utility from the WAN port. Access Web from WAN: Select to enable or disable the ability to - D-Link DVG-G1402S | Product Manual - Page 44
Browse button to locate a saved configuration file. Upload: Once you locate the file, click Upload to overwrite the current settings with the settings saved to the file. Reset to Factory Default: Click this button to reset the DVG-G1402S back to the factory default settings. D-Link Systems, Inc. 44 - D-Link DVG-G1402S | Product Manual - Page 45
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Tools > Firmware TFTP Server Address: Enter the IP address of the computer running the TFTP software. Last TFTP Server Address: The last IP address used will be displayed. Firmware Update: Select - D-Link DVG-G1402S | Product Manual - Page 46
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Tools > Time NTP Server: Enter a time server either by IP address or DNS name. Time Zone: Select your time zone from the drop-down menu. Apply: Click Apply to save your settings. D-Link Systems, - D-Link DVG-G1402S | Product Manual - Page 47
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Tools > Reboot Reboot: Click to reboot your DVG-G1402S. D-Link Systems, Inc. 47 - D-Link DVG-G1402S | Product Manual - Page 48
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Status > Device Info The Device Information screen will display the MAC address, firmware version, and the IP settings for both the WAN port and LAN port. D-Link Systems, Inc. 48 - D-Link DVG-G1402S | Product Manual - Page 49
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Status > Stats Traffic Statistics will display transmitted and received packets passing through the DVG-G1402S. Click the Refresh button to update the statistics. Clicking the Reset button will set - D-Link DVG-G1402S | Product Manual - Page 50
DVG-G1402S User's Manual Using the Configuration Utility Using the Configuration Utility (continued) Status > Diagnostics This page will allow you to test connectivity to computers and devices on your LAN by pinging. Enter the IP address you want to ping and click the Test button. D-Link Systems, - D-Link DVG-G1402S | Product Manual - Page 51
Manual Troubleshooting Troubleshooting 1. Why can't I connect the DVG-G1402S to my network? Check that the LED indicators for the broadband modem are indicating normal activity. If not, there may be a problem with the broadband connection. Check that the LED indicators on the wireless router - D-Link DVG-G1402S | Product Manual - Page 52
and "LAN" light (if the PC or another device is plugged in to the LAN port) should be lit green. Confirm that your service has been activated by your VoIP service provider. Q: After setting up the DVG-G1402S, I cannot surf the internet. A: Re-check all the cabling installations. Make sure that the - D-Link DVG-G1402S | Product Manual - Page 53
DVG-G1402S User's Manual FAQs Frequently Asked Questions Q: Can I use my DVG-G1402S on a MGCP network? A: No, the DVG-G1402S is a SIP device and uses the SIP protocol in handling all of the telephony elements. Q: I need to open certain ports, where do I go to make this configuration change? A: - D-Link DVG-G1402S | Product Manual - Page 54
DVG-G1402S User's Manual FAQs Frequently Asked Questions 5) Check your IP address. Your computer must have an IP address in the same range of the VoIP router (192.168.15.xxx) where xxx is between 2 and 254. The default gateway address must be the LAN IP address of the VoIP route (192.168.15.1). - D-Link DVG-G1402S | Product Manual - Page 55
sites such as http://www.dlink.com until you connect. Q: What port or ports do I have to open (forward) for my application to work? A: Please visit http://support.dlink.com/faq/view.asp?prod_id=1191 for a list of applications and instructions for opening (forwarding) ports. D-Link Systems, Inc. 55 - D-Link DVG-G1402S | Product Manual - Page 56
DVG-G1402S User's Manual Technical Specifications Technical Specifications Call Control Protocols Compliance: SIP2 (RFC3261) SIP1 (RFC2543) Voice Compression: G.711 (A-law and u-law), G.723.1, G.726, G.729a Analog Voice Ports: Type: Loop-Start FXS interfaces DTMF tone detection/ - D-Link DVG-G1402S | Product Manual - Page 57
DVG-G1402S User's Manual Technical Specifications Number of Ports: One 10/100BASE-T Ethernet port (WAN) Four 10/100BASE-TX Fast Ethernet port (LAN) Two loop-start FXS RJ-11 ports Standards: IEEE 802.11b IEEE 802.11g IEEE 802.3 IEEE 802.3u IEEE 802.3x Data Rate*: 802.11g: 54, 48, 36, - D-Link DVG-G1402S | Product Manual - Page 58
DVG-G1402S User's Manual Contacting Technical Support Technical Support You can find software updates and user documentation on the D-Link website. D-Link provides free technical support for customers within the United States and within Canada for the duration of the warranty period on this product - D-Link DVG-G1402S | Product Manual - Page 59
DVG-G1402S User's Manual Warranty Warranty Subject to the terms and conditions set forth herein, D-Link Systems, Inc. ("D-Link") provides this Limited warranty for its product only to the person or entity that originally purchased the product from: • D-Link or its authorized reseller or - D-Link DVG-G1402S | Product Manual - Page 60
void the user's authority to operate this equipment. D-Link declares that the DVG-G1402S (Wireless Gaming Adapter) is limited in CH1~CH11 by specified firmware controlled in the USA. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth - D-Link DVG-G1402S | Product Manual - Page 61
DVG-G1402S User's Manual Registration Registration Product registration is entirely voluntary and failure to complete or return this form will not diminish your warranty rights. Version 1.0 Revised:09/07/2005 D-Link Systems, Inc. 61
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
 |
 |
