Dacor DRR36 Installation Guide - Page 1

Installation guide Please read the installation insturctions carefully before you install the product. CAUTION DA68-03631A-03 For Lower (Align the bottom of the panel) For Lower (Align the bottom of the panel)    (FH) M4 x 14    (TH) M4 x 16    M8  M4 x 35   M6 x 12   For Upper (Align the top of the panel) BRACKET TEMPLATE COLUMN Q'TY No NAME 18"/24"/30" 36" Align the side of the panel Align the side of the panel 1 PANEL BRACKET 2 2   2 ANTI-TIP BRACKET 1 2 3 NUT-HEXAGON FLANGE 2 2 - 1 INSTALLATION 4 BOLT-HEX 12 12 GUIDE 5 SCREW-TAPPING 22 22 6 SCREW-TAPPING 24 24 7 SCREW-TAPPING 3 6  8 TOP TABLE 1 1 - 2 9 LOWER DOOR CAP 1 1 10 CAP 2 2 11 GAP GUIDE 1 1 12 TRIM TOP COVER 1 1  13 HOLDER LOCK 3 6 14-1 CABI SIDE INSULATOR 4 2 14-2 CABI SIDE INSULATOR - 2 15 INSULATOR 2 2 16 BRACKET TEMPLATE 1 1 17 INSTALLATION GUIDE 1 1 01 Uncrating the refrigerator • Remove the brackets from the pallet by unscrewing the bolts (five per bracket). 02 Attaching the anti-tip bracket • Bracket height is measured from the floor and depends on the cabinet height. • Attach the anti-tip brackets. Ensure the ₃  Cabinet Height ₈ Wooden Wall screws hold the bracket tightly. • The anti-tip brackets must extend at least 2" (50 mm) over the appliance to secure the appliance. If this minimum length cannot be observed for structural conditions Concrete wall ₈ đՏуՎՐ ₎ ʡՑуՎՋ - For 18", 24" ,30" models : 3 ea - For 36" models : 6 ea - 3 screws/holder locks per bracket it is possible to do this by fastening a spacer(wood) behind the anti-tip angle. Cabinet Height 1 83 1/2"(2121 mm) 2 83 3/4"(2127 mm) 3 84"(2134 mm) 4 84 1/4"(2140 mm) A 79 1/2"(2019 mm) 79 5/8"(2023 mm) 79 7/8"(2030 mm) 80 1/8"(2036 mm) For 36" models, place 2 anti-tip brackets at intervals. For the other models, use one anti-tip bracket. 03 Cabinet special requirements Electric supply location D 5" (127) A A : Cabinet Width B : Cabinet Depth C : Cabinet Height D : Electrical supply width location E : Electrical supply height location F : Water supply outlet location • Connect refrigerator power cord plug to a properly earthed receptacle. Set the Master Power Switch to the "I" (ON) position. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. 6" (154) B ø1/4"(6.5) C E F Water supply location *B : Includes the standard door panel thickness with 1/4" * Installation insidea cabinet of this width allows the refrigerator trim to be attached directly to the surrounding cabinets. 1" (25.4) CAUTION After power has been established, turn the Master Power Switch to the "O" (OFF) position. 18" A 18'(457 mm) B 25"(635 mm) C 84"(2,134 mm) D 8"(203 mm) E 80"(2032 mm) F 3"(76 mm) 24" 24"(610 mm) 25"(635 mm) 84"(2,134 mm) 14"(356 mm) 80"(2032 mm) 5 1/2"(140 mm) 30" 30"(762 mm) 25"(635 mm) 84"(2,134 mm) 20"(508 mm) 80"(2032 mm) 6"(152 mm) 36" 36"(915 mm) 25"(635 mm) 84"(2,134 mm) 26"(660 mm) 80"(2032 mm) 9"(228 mm) 04 Moving the refrigerator into its enclosure A A ₍ • Before moving the refrigerator into its enclosure, attach cabinet side insulators to both side of the refrigerator properly. Refer to figures below. • According to the type of cabinet, a jig (positioning aid) can be used to align the refrigerator's custom door panel with cabinet by marking vertical line on the cabinet. • Position the cabinet side chassis to align with your vertical line. Attaching insulators: For more information, refer to the installation manual. • Single Installation ՎՑٓ ŵʪɇθ ՎՑٓ 05 Leveling the refrigerator • Attach the refrigerator's top cover and trim top cover to the hook at the top front of the chassis. • Using your drill and the bit shown below, engage each of the refrigerator's adjuster shafts in turn, and level the refrigerator. ( CW ↑, CCW ↓) Adjust the gap between the furniture and upper chassis cover to 1/8 in. (3mm ). • The front and rear leveling legs have a maximum height adjustment of 3/4 in. (20mm). 06 Securing the refrigerator A • Secure the refrigerator to its enclosure with (TH) M4 x 16 screws (6 screws per side, as shown in the graphic). Aɇɵ̈ ₇ A 07 Attaching the Front-Panel Insulation • Attach the insulation to the front of refrigerator door. (Ensure the mounting position is correct.) ₐ 08 Attaching the Custom-Door-Panel Brackets STS Type Ƹť øĮǮ Wood Type Ƹť Panel Template For Upper (Align the top of the panel) BRACKET TEMPLATE COLUMN Align the side of the panel Align the side of the panel øĮǮ Recessed Back Type ₆ Panel Ɗʀθʪи Front կٓ ծٓ 9 Back ₆ Custom Panel: STS • Drive 10 screws each to the top and bottom brackets as shown in the graphic. (The other holes on each side of the bracket are for a different application.) Custom Panel: Wood, Other • The template informs you the position of the bracket and holes. • Mark hole positions on every corner of the panel according to the template and drive the screws into the holes. Custom Panel: Recessed Back, Other • If, by the nature of its design, the panel cannot be attached at the center of the bracket, use the whichever suitable screw holes on the sides of the bracket to attach the panel. • Pair Installation ˜θ̈ʒ˝ʪ ˜θͱ͝ϩ Example of 36" installation 09 Aligning the panel k Uͱͱθ ₅ U ₄ đՓ • There are two panel-adjustment mechanisms at the top and two at the bottom of the door. • Adjust the panel so it aligns with the surrounding cabinetry. • A side screw to shift the panel side to side; Screw 1 to shift the panel forward/backward; Screw 2 to set the panel in place. • To attach the Panel to the Door, screw nuts snugly onto the double-threaded bolts. (2 nuts per door)