Dacor ER36GI Installation Instructions - Page 7
Cabinet Layout - appliances
View all Dacor ER36GI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Installation Specifications Cabinet Layout • WARNING • Failure to meet or exceed the maximum and minimum dimensions/clearances stated may result in a fire hazard. • Carefully check the location where the range is to be installed. For best performance, the range should be placed away from drafts that may be caused by doors, windows and heating and air conditioning outlets. • To reduce the risk of personal injury and to reduce accumulated smoke in the room, Dacor strongly recommends installing a range hood. A range hood should project horizontally a minimum of five (5) inches beyond the face of the cabinets. If installing a range hood, see the range hood specifications for minimum clearances in addition to those stated below. • The range may be installed flush to the rear wall. Dacor recommends installing a non-combustible material on the rear wall above the range and up to the vent hood. It is not necessary to install non-combustible materials behind the range below the countertop height. • Regardless of the type of back wall surface, the range must not be installed or operated without the backguard in place. B Any openings in the wall behind the appliance or in the floor underneath it must be sealed. If cabinet storage space is to be provided directly above the range, the risk of personal injury may be reduced by installing a ventilating hood that projects horizontally a minimum of 5 inches beyond the face of the cabinets. 10" Min. (254mm) to any combustibles above counter both sides non comubustible rear wall recommended 35 1/4" (895 mm) countertop opening 36" (914 mm) cabinet opening below countertop Cabinet face below countertop Notch countertop overhang to width of cabinets Countertop Height: Min: 35 1/2" (902 mm) Max: 37 5/8" (956 mm) Countertop Thickness: Max: 1 5/8" (41mm) 24" (610mm) Countertop overhang 2 1/8" (54 mm) Max. Self-Rimming Cutout Dimensions Cabinet Depth Exactly 24 Inches5 10" Min. (254mm) to any combustibles above counter both sides rear wall or countertop edge 3/4" Min. (19mm) Countertop overhang 13" (330mm) Max.4 18" (457mm) Min.1, 4 Non-combustible surface along back wall recommended 30" (762mm) Min.1 A Top of finished counter 35 1/4" (895 mm) countertop opening 36" (914 mm) cabinet opening below countertop Cabinet face below countertop Notch countertop overhang to width of cabinets Countertop Height: Min: 35 1/2" (902 mm) Max: 37 5/8" (956 mm) Countertop Thickness: Max: 1 5/8" (41mm) 24 1/8" (613mm) Countertop overhang 2 1/8" (54mm) Max. Self-Rimming Cutout Dimensions Cabinet Depth Greater Than 24 Inches5 5 Model ER36GI only. Included self-rimming trim kit allows trim to overlap countertop. 10" (254mm Min. to combustible side walls above the range (both sides) Note 2 C Suggested location of utilities3 A6 36" minimum (914 mm) B 36" (914 mm) minimum C 37 1/8" (943 mm) maximum 6 See cutout dimensions above for self-rimming installations. 1 Vertical to combustible surface from range grate level; if installing an overhead vent hood, also check the hood specifications for minimum required clearances. 2 Cabinet/countertop depth is at discretion of customer but cabinet face SHALL NOT protrude further than rear of front panel. See product dimesions. 3 Consult local code for exact location requirements. 4 Not applicable for cabinets more than a horizontal distance of 10" (254mm) from the edge of the range. All tolerances: +1/16", -0 (+1.6, -0 mm) unless otherwise stated Cabinet Cutout Dimensions 5