Dacor MWDH27 Installation Instructions - Page 7
B Min. Width - ovens
View all Dacor MWDH27 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Installation Specifications 36" typ. (91.4 cm) Cooktop 36" typ. (91.4 cm) Warming drawer Warming drawer A B 120 Vac electrical outlet 27"/30"/36" Dacor 3/4" min.* single wall oven C (1.9 cm) D D C Warming 120 Vac drawer elect. C 3/4" min.* D (1.9 cm) Warming 120 Vac drawer elect. C 1 1/2" (3.8 cm) Typical countertop Warming drawer 3/4" min.* (1.9 cm) C 120 Vac A electrical B outlet Toe kick A Cutouts Dimensions 3/4" min.* (1.9 cm) NOTES: • Models EWD36 and OWD24 cannot be installed above or below another warming drawer (any type). • Model OWD24 is not approved for installation above, below or adjacent to a wall oven or a warming drawer, including the same model. Model ERWD27 ERWD30 EWD24 EWD27 EWD30 EWD36 IWD24 IWD27 IWD30 MRWD27 MRWD30 MWDH27 MWDH30 MWDV27 MWDV30 OWD24 (A) Cutout Width 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 22 1/2" (57.2 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 34 1/2" (87.6 cm) 22 1/2" (57.2 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 25 1/2" (64.8 cm) 28 1/2" (72.4 cm) 22 5/8" (57.5 cm) (B) Min. Width to Adjacent Doors/ Drawers 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 24 1/4" (61.6 cm)* 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 36 1/4" (92.1 cm)* ** ** ** 27" (68.6 cm)* 30" (76.2 cm)* 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 27 1/4" (69.2 cm)* 30 1/4" (76.8 cm)* 24 1/4" (61.6 cm)*** (C) Cutout Height 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 9 1/8" (23.2 cm) 11 15/16" (30.3 cm) (D) Min. Vertical Gap Between Cutouts 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* NA 1 1/16" (2.7 cm) 1 1/16" (2.7 cm) 1 1/16" (2.7 cm) 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* 1 1/4" (3.2 cm)* NA Min. Cutout Depth 24" (61.0 cm) 20 1/8" (51.1 cm) * Bare minimum spacing to allow for ventilation and avoid scraping on ERW, EWD, MRW and MWD series models. ** IWD models or OWD24 without the optional front panel kit: The chassis and drawer faceplate are smaller than the cutout. The custom front panel mounts to the drawer faceplate. The height and width of the custom front panel must exceed the cutout dimensions (A and C above) to cover the hole. Allow 1/4" minimum additional space on the top, bottom and sides from the custom front panel edge to prevent scraping against adjacent doors, drawers and the countertop. *** OWD24 with optional factory front panel kit only. Bare minimum spacing shown to avoid scraping. Gap above and below cutout is 3/4" minimum. See ** above for OWD24 with custom front panel. 5